arm: dts: dra7: sync DT with latest Linux
Sync all dra7* specific dts files with the upstream
kernel including changes queued for 4.14
https://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap.git/log/?h=omap-for-v4.14/dt-v3
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
diff --git a/arch/arm/dts/am57xx-idk-common.dtsi b/arch/arm/dts/am57xx-idk-common.dtsi
index 30118ed..97aa8e6 100644
--- a/arch/arm/dts/am57xx-idk-common.dtsi
+++ b/arch/arm/dts/am57xx-idk-common.dtsi
@@ -47,6 +47,74 @@
regulator-always-on;
regulator-boot-on;
};
+
+ leds-iio {
+ status = "disabled";
+ compatible = "gpio-leds";
+ led-out0 {
+ label = "out0";
+ gpios = <&tpic2810 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ led-out1 {
+ label = "out1";
+ gpios = <&tpic2810 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ led-out2 {
+ label = "out2";
+ gpios = <&tpic2810 2 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ led-out3 {
+ label = "out3";
+ gpios = <&tpic2810 3 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ led-out4 {
+ label = "out4";
+ gpios = <&tpic2810 4 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ led-out5 {
+ label = "out5";
+ gpios = <&tpic2810 5 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ led-out6 {
+ label = "out6";
+ gpios = <&tpic2810 6 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ led-out7 {
+ label = "out7";
+ gpios = <&tpic2810 7 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+ };
+};
+
+&dra7_pmx_core {
+ dcan1_pins_default: dcan1_pins_default {
+ pinctrl-single,pins = <
+ DRA7XX_CORE_IOPAD(0x37d0, PIN_OUTPUT_PULLUP | MUX_MODE0) /* dcan1_tx */
+ DRA7XX_CORE_IOPAD(0x37d4, PIN_INPUT_PULLUP | MUX_MODE0) /* dcan1_rx */
+ >;
+ };
+
+ dcan1_pins_sleep: dcan1_pins_sleep {
+ pinctrl-single,pins = <
+ DRA7XX_CORE_IOPAD(0x37d0, MUX_MODE15 | PULL_UP) /* dcan1_tx.off */
+ DRA7XX_CORE_IOPAD(0x37d4, MUX_MODE15 | PULL_UP) /* dcan1_rx.off */
+ >;
+ };
};
&i2c1 {
@@ -61,6 +129,7 @@
#interrupt-cells = <2>;
interrupt-controller;
ti,system-power-controller;
+ ti,palmas-override-powerhold;
tps659038_pmic {
compatible = "ti,tps659038-pmic";
@@ -254,6 +323,35 @@
gpio-controller;
#gpio-cells = <2>;
};
+
+ extcon_usb2: tps659038_usb {
+ compatible = "ti,palmas-usb-vid";
+ ti,enable-vbus-detection;
+ ti,enable-id-detection;
+ /* ID & VBUS GPIOs provided in board dts */
+ };
+ };
+
+ tpic2810: tpic2810@60 {
+ compatible = "ti,tpic2810";
+ reg = <0x60>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+};
+
+&mcspi3 {
+ status = "okay";
+ ti,pindir-d0-out-d1-in;
+
+ sn65hvs882: sn65hvs882@0 {
+ compatible = "pisosr-gpio";
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ reg = <0>;
+ spi-max-frequency = <1000000>;
+ spi-cpol;
};
};
@@ -298,7 +396,15 @@
};
&usb2 {
- dr_mode = "otg";
+ dr_mode = "peripheral";
+};
+
+&mmc1 {
+ status = "okay";
+ vmmc-supply = <&v3_3d>;
+ vqmmc-supply = <&ldo1_reg>;
+ bus-width = <4>;
+ cd-gpios = <&gpio6 27 GPIO_ACTIVE_LOW>; /* gpio 219 */
};
&mmc2 {
@@ -309,12 +415,20 @@
max-frequency = <96000000>;
};
+&dcan1 {
+ status = "okay";
+ pinctrl-names = "default", "sleep", "active";
+ pinctrl-0 = <&dcan1_pins_sleep>;
+ pinctrl-1 = <&dcan1_pins_sleep>;
+ pinctrl-2 = <&dcan1_pins_default>;
+};
+
&qspi {
status = "okay";
spi-max-frequency = <76800000>;
m25p80@0 {
- compatible = "s25fl256s1", "spi-flash", "jedec,spi-nor";
+ compatible = "s25fl256s1", "jedec,spi-nor";
spi-max-frequency = <76800000>;
reg = <0>;
spi-tx-bus-width = <1>;