diff --git a/arch/mips/dts/mrvl,cn73xx.dtsi b/arch/mips/dts/mrvl,cn73xx.dtsi
index 40eb85e..27cdfd0 100644
--- a/arch/mips/dts/mrvl,cn73xx.dtsi
+++ b/arch/mips/dts/mrvl,cn73xx.dtsi
@@ -134,6 +134,33 @@
 			clocks = <&clk OCTEON_CLK_IO>;
 		};
 
+		mmc: mmc@1180000002000 {
+			compatible = "cavium,octeon-7890-mmc",
+				     "cavium,octeon-7360-mmc";
+			reg = <0x11800 0x00000000 0x0 0x2100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			/* EMM_INT_BUF_DONE,
+			   EMM_INT_CMD_DONE,
+			   EMM_INT_DMA_DONE,
+			   EMM_INT_CMD_ERR,
+			   EMM_INT_DMA_ERR,
+			   EMM_INT_SWITCH_DONE,
+			   EMM_INT_SWITCH_ERR,
+			   EMM_DMA_DONE,
+			   EMM_DMA_FIFO*/
+			interrupts = <0x09040 1>,
+				     <0x09041 1>,
+				     <0x09042 1>,
+				     <0x09043 1>,
+				     <0x09044 1>,
+				     <0x09045 1>,
+				     <0x09046 1>,
+				     <0x09000 1>,
+				     <0x09001 1>;
+			clocks = <&clk OCTEON_CLK_IO>;
+		};
+
 		spi: spi@1070000001000 {
 			compatible = "cavium,octeon-3010-spi";
 			reg = <0x10700 0x00001000 0x0 0x100>;
diff --git a/arch/mips/dts/mrvl,octeon-ebb7304.dts b/arch/mips/dts/mrvl,octeon-ebb7304.dts
index 993b4f6..1bb34e1 100644
--- a/arch/mips/dts/mrvl,octeon-ebb7304.dts
+++ b/arch/mips/dts/mrvl,octeon-ebb7304.dts
@@ -6,16 +6,36 @@
 /dts-v1/;
 
 #include "mrvl,cn73xx.dtsi"
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	model = "cavium,ebb7304";
 	compatible = "cavium,ebb7304";
 
 	aliases {
+		mmc0 = &mmc0;
+		mmc1 = &mmc1;
 		serial0 = &uart0;
 		spi0 = &spi;
 	};
 
+	regulators {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Power on GPIO 8, active high */
+		reg_mmc_3v3: regulator@0 {
+			compatible = "regulator-fixed";
+			reg = <0>;
+			regulator-name = "mmc-3v3";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			gpio = <&gpio 8 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+		};
+	};
+
 	chosen {
 		stdout-path = &uart0;
 	};
@@ -137,3 +157,40 @@
 	 */
 	power = <&gpio 21 0>;
 };
+
+&mmc {
+	status = "okay";
+
+	/* The board has two MMC slots
+	 * If both are occupied, the speed must be reduced,
+	 * as extra data-line load increases slew time,
+	 * and dat-skew adjustment does not help significantly.
+	 */
+	mmc0: mmc-slot@0 {
+		compatible = "cavium,octeon-6130-mmc-slot", "mmc-slot";
+		reg = <0>;
+		vqmmc-supply = <&reg_mmc_3v3>;
+		voltage-ranges = <3300 3300>;
+		//spi-max-frequency = <52000000>; // just one
+		spi-max-frequency = <37000000>; // both slots
+		/* bus width can be 1, 4 or 8 */
+		bus-width = <8>; /* new std property */
+		cavium,bus-max-width = <8>; /* custom property */
+		wp-gpios = <&gpio 22 0>; /* active high */
+		cd-gpios = <&gpio 23 1>; /* active low */
+	};
+
+	mmc1: mmc-slot@1 {
+		compatible = "cavium,octeon-6130-mmc-slot", "mmc-slot";
+		reg = <1>;
+		vqmmc-supply = <&reg_mmc_3v3>;
+		voltage-ranges = <3300 3300>;
+		//spi-max-frequency = <52000000>; // just one
+		spi-max-frequency = <37000000>; // both slots
+		/* bus width can be 1, 4 or 8 */
+		bus-width = <8>; /* new std property */
+		cavium,bus-max-width = <8>; /* custom property */
+		wp-gpios = <&gpio 24 0>; /* active high */
+		cd-gpios = <&gpio 25 1>; /* active low */
+	};
+};
diff --git a/arch/mips/dts/mscc,jr2.dtsi b/arch/mips/dts/mscc,jr2.dtsi
index c44e9a2..87db7ca 100644
--- a/arch/mips/dts/mscc,jr2.dtsi
+++ b/arch/mips/dts/mscc,jr2.dtsi
@@ -243,7 +243,9 @@
 			      <0x017d0000 0x10000>,  // QFWD
 			      <0x01020000 0x20000>,  // QS
 			      <0x017e0000 0x10000>,  // QSYS
-			      <0x01b00000 0x80000>;  // REW
+			      <0x01b00000 0x80000>,  // REW
+			      <0x01010000 0x100>,    // GCB
+			      <0x00000000 0x100>;    // ICPU
 			reg-names = "port0", "port1", "port2", "port3", "port4",
 				    "port5", "port6", "port7", "port8", "port9",
 				    "port10", "port11", "port12", "port13",
@@ -257,7 +259,7 @@
 				    "port42", "port43", "port44", "port45",
 				    "port46", "port47", "ana_ac", "ana_cl",
 				    "ana_l2", "asm", "hsio", "lrn", "qfwd",
-				    "qs", "qsys", "rew";
+				    "qs", "qsys", "rew", "gcb", "icpu";
 			status = "okay";
 
 			ethernet-ports {
diff --git a/arch/mips/mach-mtmips/mt7628/ddr.c b/arch/mips/mach-mtmips/mt7628/ddr.c
index b091f2e..4e72459 100644
--- a/arch/mips/mach-mtmips/mt7628/ddr.c
+++ b/arch/mips/mach-mtmips/mt7628/ddr.c
@@ -140,6 +140,9 @@
 	lspd = readl(sysc + SYSCTL_CLKCFG0_REG) &
 	       (CPU_PLL_FROM_BBP | CPU_PLL_FROM_XTAL);
 
+	if (pkg_type == PKG_ID_KN)
+		ddr_type = DRAM_DDR1;
+
 	mt7628_memc_reset(1);
 	__udelay(200);
 
@@ -152,9 +155,6 @@
 	param.memsize = 0;
 	param.bus_width = 0;
 
-	if (pkg_type == PKG_ID_KN)
-		ddr_type = DRAM_DDR1;
-
 	if (ddr_type == DRAM_DDR1) {
 		if (lspd)
 			param.cfgs = ddr1_cfgs_160mhz;
diff --git a/arch/mips/mach-mtmips/mt7628/init.c b/arch/mips/mach-mtmips/mt7628/init.c
index 7c531ff..6b53512 100644
--- a/arch/mips/mach-mtmips/mt7628/init.c
+++ b/arch/mips/mach-mtmips/mt7628/init.c
@@ -68,6 +68,9 @@
 	val = readl(sysc + SYSCTL_EFUSE_CFG_REG);
 	ee = val & EFUSE_MT7688;
 
+	if (pkg == PKG_ID_KN)
+		ddr = DRAM_DDR1;
+
 	printf("CPU:   MediaTek MT%u%c ver:%u eco:%u\n",
 	       ee ? 7688 : 7628, pkg ? 'A' : 'K', ver, eco);
 
diff --git a/arch/mips/mach-octeon/include/mach/cvmx-mio-emm-defs.h b/arch/mips/mach-octeon/include/mach/cvmx-mio-emm-defs.h
new file mode 100644
index 0000000..3572a59
--- /dev/null
+++ b/arch/mips/mach-octeon/include/mach/cvmx-mio-emm-defs.h
@@ -0,0 +1,614 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) 2020 Marvell International Ltd.
+ */
+
+#ifndef __CVMX_MIO_EMM_DEFS_H__
+#define __CVMX_MIO_EMM_DEFS_H__
+
+static inline u64 MIO_EMM_DMA_FIFO_CFG(void)
+{
+	return 0x160;
+}
+
+static inline u64 MIO_EMM_DMA_FIFO_ADR(void)
+{
+	return 0x170;
+}
+
+static inline u64 MIO_EMM_DMA_FIFO_CMD(void)
+{
+	return 0x178;
+}
+
+static inline u64 MIO_EMM_DMA_CFG(void)
+{
+	return 0x180;
+}
+
+static inline u64 MIO_EMM_DMA_ADR(void)
+{
+	return 0x188;
+}
+
+static inline u64 MIO_EMM_DMA_INT(void)
+{
+	return 0x190;
+}
+
+static inline u64 MIO_EMM_CFG(void)
+{
+	return 0x2000;
+}
+
+static inline u64 MIO_EMM_MODEX(u64 a)
+{
+	return 0x2008 + 8 * a;
+}
+
+static inline u64 MIO_EMM_SWITCH(void)
+{
+	return 0x2048;
+}
+
+static inline u64 MIO_EMM_DMA(void)
+{
+	return 0x2050;
+}
+
+static inline u64 MIO_EMM_CMD(void)
+{
+	return 0x2058;
+}
+
+static inline u64 MIO_EMM_RSP_STS(void)
+{
+	return 0x2060;
+}
+
+static inline u64 MIO_EMM_RSP_LO(void)
+{
+	return 0x2068;
+}
+
+static inline u64 MIO_EMM_RSP_HI(void)
+{
+	return 0x2070;
+}
+
+static inline u64 MIO_EMM_INT(void)
+{
+	return 0x2078;
+}
+
+static inline u64 MIO_EMM_WDOG(void)
+{
+	return 0x2088;
+}
+
+static inline u64 MIO_EMM_SAMPLE(void)
+{
+	return 0x2090;
+}
+
+static inline u64 MIO_EMM_STS_MASK(void)
+{
+	return 0x2098;
+}
+
+static inline u64 MIO_EMM_RCA(void)
+{
+	return 0x20a0;
+}
+
+static inline u64 MIO_EMM_BUF_IDX(void)
+{
+	return 0x20e0;
+}
+
+static inline u64 MIO_EMM_BUF_DAT(void)
+{
+	return 0x20e8;
+}
+
+/* Dummy implementation, not documented on MIPS Octeon */
+static inline u64 MIO_EMM_DEBUG(void)
+{
+	return 0x20f8;
+}
+
+/**
+ * mio_emm_access_wdog
+ */
+union mio_emm_access_wdog {
+	u64 u;
+	struct mio_emm_access_wdog_s {
+		uint64_t reserved_32_63 : 32;
+		uint64_t clk_cnt : 32;
+	} s;
+};
+
+/**
+ * mio_emm_buf_dat
+ *
+ * MIO_EMM_BUF_DAT = MIO EMMC Data buffer access Register
+ *
+ */
+union mio_emm_buf_dat {
+	u64 u;
+	struct mio_emm_buf_dat_s {
+		uint64_t dat : 64;
+	} s;
+};
+
+/**
+ * mio_emm_buf_idx
+ *
+ * MIO_EMM_BUF_IDX = MIO EMMC Data buffer address Register
+ *
+ */
+union mio_emm_buf_idx {
+	u64 u;
+	struct mio_emm_buf_idx_s {
+		uint64_t reserved_17_63 : 47;
+		uint64_t inc : 1;
+		uint64_t reserved_7_15 : 9;
+		uint64_t buf_num : 1;
+		uint64_t offset : 6;
+	} s;
+};
+
+/**
+ * mio_emm_cfg
+ *
+ * MIO_EMM_CFG = MIO EMMC Configuration Register
+ *
+ */
+union mio_emm_cfg {
+	u64 u;
+	struct mio_emm_cfg_s {
+		uint64_t reserved_17_63 : 47;
+		uint64_t boot_fail : 1;
+		uint64_t reserved_4_15 : 12;
+		uint64_t bus_ena : 4;
+	} s;
+};
+
+/**
+ * mio_emm_cmd
+ *
+ * MIO_EMM_CMD = MIO EMMC Command Register
+ *
+ */
+union mio_emm_cmd {
+	u64 u;
+	struct mio_emm_cmd_s {
+		uint64_t reserved_63_63 : 1;
+		uint64_t skip_busy : 1;
+		uint64_t bus_id : 2;
+		uint64_t cmd_val : 1;
+		uint64_t reserved_56_58 : 3;
+		uint64_t dbuf : 1;
+		uint64_t offset : 6;
+		uint64_t reserved_43_48 : 6;
+		uint64_t ctype_xor : 2;
+		uint64_t rtype_xor : 3;
+		uint64_t cmd_idx : 6;
+		uint64_t arg : 32;
+	} s;
+};
+
+/**
+ * mio_emm_dma
+ *
+ * MIO_EMM_DMA = MIO EMMC DMA config Register
+ *
+ */
+union mio_emm_dma {
+	u64 u;
+	struct mio_emm_dma_s {
+		uint64_t reserved_63_63 : 1;
+		uint64_t skip_busy : 1;
+		uint64_t bus_id : 2;
+		uint64_t dma_val : 1;
+		uint64_t sector : 1;
+		uint64_t dat_null : 1;
+		uint64_t thres : 6;
+		uint64_t rel_wr : 1;
+		uint64_t rw : 1;
+		uint64_t multi : 1;
+		uint64_t block_cnt : 16;
+		uint64_t card_addr : 32;
+	} s;
+};
+
+/**
+ * mio_emm_dma_adr
+ *
+ * This register sets the address for eMMC/SD flash transfers to/from memory. Sixty-four-bit
+ * operations must be used to access this register. This register is updated by the DMA
+ * hardware and can be reloaded by the values placed in the MIO_EMM_DMA_FIFO_ADR.
+ */
+union mio_emm_dma_adr {
+	u64 u;
+	struct mio_emm_dma_adr_s {
+		uint64_t reserved_42_63 : 22;
+		uint64_t adr : 42;
+	} s;
+};
+
+/**
+ * mio_emm_dma_cfg
+ *
+ * This register controls the internal DMA engine used with the eMMC/SD flash controller. Sixty-
+ * four-bit operations must be used to access this register. This register is updated by the
+ * hardware DMA engine and can also be reloaded by writes to the MIO_EMM_DMA_FIFO_CMD register.
+ */
+union mio_emm_dma_cfg {
+	u64 u;
+	struct mio_emm_dma_cfg_s {
+		uint64_t en : 1;
+		uint64_t rw : 1;
+		uint64_t clr : 1;
+		uint64_t reserved_60_60 : 1;
+		uint64_t swap32 : 1;
+		uint64_t swap16 : 1;
+		uint64_t swap8 : 1;
+		uint64_t endian : 1;
+		uint64_t size : 20;
+		uint64_t reserved_0_35 : 36;
+	} s;
+};
+
+/**
+ * mio_emm_dma_fifo_adr
+ *
+ * This register specifies the internal address that is loaded into the eMMC internal DMA FIFO.
+ * The FIFO is used to queue up operations for the MIO_EMM_DMA_CFG/MIO_EMM_DMA_ADR when the DMA
+ * completes successfully.
+ */
+union mio_emm_dma_fifo_adr {
+	u64 u;
+	struct mio_emm_dma_fifo_adr_s {
+		uint64_t reserved_42_63 : 22;
+		uint64_t adr : 39;
+		uint64_t reserved_0_2 : 3;
+	} s;
+};
+
+/**
+ * mio_emm_dma_fifo_cfg
+ *
+ * This register controls DMA FIFO operations.
+ *
+ */
+union mio_emm_dma_fifo_cfg {
+	u64 u;
+	struct mio_emm_dma_fifo_cfg_s {
+		uint64_t reserved_17_63 : 47;
+		uint64_t clr : 1;
+		uint64_t reserved_13_15 : 3;
+		uint64_t int_lvl : 5;
+		uint64_t reserved_5_7 : 3;
+		uint64_t count : 5;
+	} s;
+};
+
+/**
+ * mio_emm_dma_fifo_cmd
+ *
+ * This register specifies a command that is loaded into the eMMC internal DMA FIFO.  The FIFO is
+ * used to queue up operations for the MIO_EMM_DMA_CFG/MIO_EMM_DMA_ADR when the DMA completes
+ * successfully. Writes to this register store both the MIO_EMM_DMA_FIFO_CMD and the
+ * MIO_EMM_DMA_FIFO_ADR contents into the FIFO and increment the MIO_EMM_DMA_FIFO_CFG[COUNT]
+ * field.
+ *
+ * Note: This register has a similar format to MIO_EMM_DMA_CFG with the exception
+ * that the EN and CLR fields are absent. These are supported in MIO_EMM_DMA_FIFO_CFG.
+ */
+union mio_emm_dma_fifo_cmd {
+	u64 u;
+	struct mio_emm_dma_fifo_cmd_s {
+		uint64_t reserved_63_63 : 1;
+		uint64_t rw : 1;
+		uint64_t reserved_61_61 : 1;
+		uint64_t intdis : 1;
+		uint64_t swap32 : 1;
+		uint64_t swap16 : 1;
+		uint64_t swap8 : 1;
+		uint64_t endian : 1;
+		uint64_t size : 20;
+		uint64_t reserved_0_35 : 36;
+	} s;
+};
+
+/**
+ * mio_emm_dma_int
+ *
+ * Sixty-four-bit operations must be used to access this register.
+ *
+ */
+union mio_emm_dma_int {
+	u64 u;
+	struct mio_emm_dma_int_s {
+		uint64_t reserved_2_63 : 62;
+		uint64_t fifo : 1;
+		uint64_t done : 1;
+	} s;
+};
+
+/**
+ * mio_emm_dma_int_w1s
+ */
+union mio_emm_dma_int_w1s {
+	u64 u;
+	struct mio_emm_dma_int_w1s_s {
+		uint64_t reserved_2_63 : 62;
+		uint64_t fifo : 1;
+		uint64_t done : 1;
+	} s;
+};
+
+/**
+ * mio_emm_int
+ *
+ * MIO_EMM_INT = MIO EMMC Interrupt Register
+ *
+ */
+union mio_emm_int {
+	u64 u;
+	struct mio_emm_int_s {
+		uint64_t reserved_7_63 : 57;
+		uint64_t switch_err : 1;
+		uint64_t switch_done : 1;
+		uint64_t dma_err : 1;
+		uint64_t cmd_err : 1;
+		uint64_t dma_done : 1;
+		uint64_t cmd_done : 1;
+		uint64_t buf_done : 1;
+	} s;
+};
+
+/**
+ * mio_emm_int_en
+ *
+ * MIO_EMM_INT_EN = MIO EMMC Interrupt enable Register
+ *
+ */
+union mio_emm_int_en {
+	u64 u;
+	struct mio_emm_int_en_s {
+		uint64_t reserved_7_63 : 57;
+		uint64_t switch_err : 1;
+		uint64_t switch_done : 1;
+		uint64_t dma_err : 1;
+		uint64_t cmd_err : 1;
+		uint64_t dma_done : 1;
+		uint64_t cmd_done : 1;
+		uint64_t buf_done : 1;
+	} s;
+};
+
+/**
+ * mio_emm_int_w1s
+ */
+union mio_emm_int_w1s {
+	u64 u;
+	struct mio_emm_int_w1s_s {
+		uint64_t reserved_7_63 : 57;
+		uint64_t switch_err : 1;
+		uint64_t switch_done : 1;
+		uint64_t dma_err : 1;
+		uint64_t cmd_err : 1;
+		uint64_t dma_done : 1;
+		uint64_t cmd_done : 1;
+		uint64_t buf_done : 1;
+	} s;
+};
+
+/**
+ * mio_emm_mode#
+ *
+ * MIO_EMM_MODE = MIO EMMC Operating mode Register
+ *
+ */
+union mio_emm_modex {
+	u64 u;
+	struct mio_emm_modex_s {
+		uint64_t reserved_49_63 : 15;
+		uint64_t hs_timing : 1;
+		uint64_t reserved_43_47 : 5;
+		uint64_t bus_width : 3;
+		uint64_t reserved_36_39 : 4;
+		uint64_t power_class : 4;
+		uint64_t clk_hi : 16;
+		uint64_t clk_lo : 16;
+	} s;
+};
+
+/**
+ * mio_emm_rca
+ */
+union mio_emm_rca {
+	u64 u;
+	struct mio_emm_rca_s {
+		uint64_t reserved_16_63 : 48;
+		uint64_t card_rca : 16;
+	} s;
+};
+
+/**
+ * mio_emm_rsp_hi
+ *
+ * MIO_EMM_RSP_HI = MIO EMMC Response data high Register
+ *
+ */
+union mio_emm_rsp_hi {
+	u64 u;
+	struct mio_emm_rsp_hi_s {
+		uint64_t dat : 64;
+	} s;
+};
+
+/**
+ * mio_emm_rsp_lo
+ *
+ * MIO_EMM_RSP_LO = MIO EMMC Response data low Register
+ *
+ */
+union mio_emm_rsp_lo {
+	u64 u;
+	struct mio_emm_rsp_lo_s {
+		uint64_t dat : 64;
+	} s;
+};
+
+/**
+ * mio_emm_rsp_sts
+ *
+ * MIO_EMM_RSP_STS = MIO EMMC Response status Register
+ *
+ */
+union mio_emm_rsp_sts {
+	u64 u;
+	struct mio_emm_rsp_sts_s {
+		uint64_t reserved_62_63 : 2;
+		uint64_t bus_id : 2;
+		uint64_t cmd_val : 1;
+		uint64_t switch_val : 1;
+		uint64_t dma_val : 1;
+		uint64_t dma_pend : 1;
+		uint64_t acc_timeout : 1;
+		uint64_t reserved_29_54 : 26;
+		uint64_t dbuf_err : 1;
+		uint64_t reserved_24_27 : 4;
+		uint64_t dbuf : 1;
+		uint64_t blk_timeout : 1;
+		uint64_t blk_crc_err : 1;
+		uint64_t rsp_busybit : 1;
+		uint64_t stp_timeout : 1;
+		uint64_t stp_crc_err : 1;
+		uint64_t stp_bad_sts : 1;
+		uint64_t stp_val : 1;
+		uint64_t rsp_timeout : 1;
+		uint64_t rsp_crc_err : 1;
+		uint64_t rsp_bad_sts : 1;
+		uint64_t rsp_val : 1;
+		uint64_t rsp_type : 3;
+		uint64_t cmd_type : 2;
+		uint64_t cmd_idx : 6;
+		uint64_t cmd_done : 1;
+	} s;
+};
+
+/**
+ * mio_emm_sample
+ */
+union mio_emm_sample {
+	u64 u;
+	struct mio_emm_sample_s {
+		uint64_t reserved_26_63 : 38;
+		uint64_t cmd_cnt : 10;
+		uint64_t reserved_10_15 : 6;
+		uint64_t dat_cnt : 10;
+	} s;
+};
+
+/**
+ * mio_emm_sts_mask
+ */
+union mio_emm_sts_mask {
+	u64 u;
+	struct mio_emm_sts_mask_s {
+		uint64_t reserved_32_63 : 32;
+		uint64_t sts_msk : 32;
+	} s;
+};
+
+/**
+ * mio_emm_switch
+ *
+ * MIO_EMM_SWITCH = MIO EMMC Operating mode switch Register
+ *
+ */
+union mio_emm_switch {
+	u64 u;
+	struct mio_emm_switch_s {
+		uint64_t reserved_62_63 : 2;
+		uint64_t bus_id : 2;
+		uint64_t switch_exe : 1;
+		uint64_t switch_err0 : 1;
+		uint64_t switch_err1 : 1;
+		uint64_t switch_err2 : 1;
+		uint64_t reserved_49_55 : 7;
+		uint64_t hs_timing : 1;
+		uint64_t reserved_43_47 : 5;
+		uint64_t bus_width : 3;
+		uint64_t reserved_36_39 : 4;
+		uint64_t power_class : 4;
+		uint64_t clk_hi : 16;
+		uint64_t clk_lo : 16;
+	} s;
+};
+
+/**
+ * mio_emm_wdog
+ *
+ * MIO_EMM_WDOG = MIO EMMC Watchdog Register
+ *
+ */
+union mio_emm_wdog {
+	u64 u;
+	struct mio_emm_wdog_s {
+		uint64_t reserved_26_63 : 38;
+		uint64_t clk_cnt : 26;
+	} s;
+};
+
+/*
+ * The following structs are only available to enable compilation of the common
+ * MMC driver. These registers do not exist on MIPS Octeon.
+ */
+
+/**
+ * Register (RSL) mio_emm_timing
+ *
+ * eMMC Timing Register This register determines the number of tap delays
+ * the EMM_DAT, EMM_DS, and EMM_CMD lines are transmitted or received in
+ * relation to EMM_CLK. These values should only be changed when the eMMC
+ * bus is idle.
+ */
+union mio_emm_timing {
+	u64 u;
+	struct mio_emm_timing_s {
+		u64 data_out_tap                     : 6;
+		u64 reserved_6_15                    : 10;
+		u64 data_in_tap                      : 6;
+		u64 reserved_22_31                   : 10;
+		u64 cmd_out_tap                      : 6;
+		u64 reserved_38_47                   : 10;
+		u64 cmd_in_tap                       : 6;
+		u64 reserved_54_63                   : 10;
+	} s;
+};
+
+/**
+ * Register (RSL) mio_emm_debug
+ *
+ * eMMC Debug Register
+ */
+union mio_emm_debug {
+	u64 u;
+	struct mio_emm_debug_s {
+		u64 clk_on                           : 1;
+		u64 reserved_1_7                     : 7;
+		u64 cmd_sm                           : 4;
+		u64 data_sm                          : 4;
+		u64 dma_sm                           : 4;
+		u64 emmc_clk_disable                 : 1;
+		u64 rdsync_rst                       : 1;
+		u64 reserved_22_63                   : 42;
+	} s;
+};
+
+#endif
diff --git a/configs/octeon_ebb7304_defconfig b/configs/octeon_ebb7304_defconfig
index a98d73a..ae93b49 100644
--- a/configs/octeon_ebb7304_defconfig
+++ b/configs/octeon_ebb7304_defconfig
@@ -14,6 +14,7 @@
 CONFIG_HUSH_PARSER=y
 CONFIG_CMD_GPIO=y
 CONFIG_CMD_I2C=y
+CONFIG_CMD_MMC=y
 CONFIG_CMD_MTD=y
 CONFIG_CMD_PART=y
 CONFIG_CMD_PCI=y
@@ -24,12 +25,17 @@
 CONFIG_CMD_EXT4=y
 CONFIG_CMD_FAT=y
 CONFIG_CMD_FS_GENERIC=y
-# CONFIG_DOS_PARTITION is not set
+CONFIG_AMIGA_PARTITION=y
+CONFIG_EFI_PARTITION=y
+CONFIG_PARTITION_TYPE_GUID=y
 CONFIG_ENV_IS_IN_FLASH=y
 CONFIG_ENV_ADDR=0x1FBFE000
-CONFIG_BLK=y
 CONFIG_CLK=y
 # CONFIG_INPUT is not set
+CONFIG_MISC=y
+CONFIG_MMC=y
+CONFIG_DM_MMC=y
+CONFIG_MMC_OCTEONTX=y
 CONFIG_MTD=y
 CONFIG_DM_MTD=y
 CONFIG_MTD_NOR_FLASH=y
@@ -45,6 +51,8 @@
 # CONFIG_NETDEVICES is not set
 CONFIG_PCI=y
 CONFIG_DM_PCI=y
+CONFIG_DM_REGULATOR=y
+CONFIG_DM_REGULATOR_FIXED=y
 CONFIG_RAM=y
 CONFIG_RAM_OCTEON=y
 CONFIG_RAM_OCTEON_DDR4=y
@@ -59,6 +67,7 @@
 CONFIG_DM_USB=y
 CONFIG_USB_XHCI_HCD=y
 CONFIG_USB_XHCI_DWC3=y
+CONFIG_USB_STORAGE=y
 CONFIG_USB_HOST_ETHER=y
 CONFIG_USB_ETHER_ASIX=y
 CONFIG_USB_ETHER_ASIX88179=y
diff --git a/drivers/mmc/Kconfig b/drivers/mmc/Kconfig
index d862d1e..f4ad1db 100644
--- a/drivers/mmc/Kconfig
+++ b/drivers/mmc/Kconfig
@@ -317,13 +317,13 @@
 	  If you have an MMC controller on a PCI bus, say Y here.
 
 config MMC_OCTEONTX
-	bool "Marvell OcteonTX Multimedia Card Interface support"
-	depends on (ARCH_OCTEONTX || ARCH_OCTEONTX2)
+	bool "Marvell Octeon Multimedia Card Interface support"
+	depends on (ARCH_OCTEON || ARCH_OCTEONTX || ARCH_OCTEONTX2)
 	depends on DM_MMC
 	help
-	  This selects the OcteonTX Multimedia card Interface.
-	  If you have an OcteonTX/TX2 board with a Multimedia Card slot,
-	  say Y here.
+	  This selects the Octeon Multimedia card Interface.
+	  If you have an OcteonTX/TX2 or MIPS Octeon board with a
+	  Multimedia Card slot, say Y here.
 
 	  If unsure, say N.
 
diff --git a/drivers/mmc/octeontx_hsmmc.c b/drivers/mmc/octeontx_hsmmc.c
index 442ca49..2e569a9 100644
--- a/drivers/mmc/octeontx_hsmmc.c
+++ b/drivers/mmc/octeontx_hsmmc.c
@@ -1,13 +1,12 @@
 // SPDX-License-Identifier:    GPL-2.0
 /*
  * Copyright (C) 2019 Marvell International Ltd.
- *
- * https://spdx.org/licenses
  */
 
-//#define DEBUG
+#include <clk.h>
 #include <cpu_func.h>
 #include <dm.h>
+#include <dm/device-internal.h>
 #include <dm/lists.h>
 #include <env.h>
 #include <errno.h>
@@ -19,23 +18,31 @@
 #include <part.h>
 #include <pci.h>
 #include <pci_ids.h>
+#include <power/regulator.h>
 #include <time.h>
 #include <watchdog.h>
-
+#include <asm/io.h>
 #include <linux/delay.h>
 #include <linux/kernel.h>
 #include <linux/libfdt.h>
 
+#if defined(CONFIG_ARCH_OCTEON)
+#include <mach/octeon-model.h>
+#include <mach/cvmx-regs.h>
+#include <mach/cvmx-mio-emm-defs.h>
+#else
 #include <asm/arch/board.h>
 #include <asm/arch/clock.h>
 #include <asm/arch/csrs/csrs-mio_emm.h>
-#include <asm/io.h>
-#include <dm/device-internal.h>
-
-#include <power/regulator.h>
+#endif
 
 #include "octeontx_hsmmc.h"
 
+/* Use dummy implementation for MIPS Octeon to always return false */
+#if defined(CONFIG_ARCH_OCTEON)
+#define otx_is_soc(ver)		0
+#endif
+
 #define MMC_TIMEOUT_SHORT	20	/* in ms */
 #define MMC_TIMEOUT_LONG	1000
 #define MMC_TIMEOUT_ERASE	10000
@@ -71,16 +78,18 @@
 #define MMC_DEFAULT_TAP_DELAY			4
 #define TOTAL_NO_OF_TAPS			512
 static void octeontx_mmc_switch_to(struct mmc *mmc);
-static int octeontx_mmc_configure_delay(struct mmc *mmc);
-static void octeontx_mmc_set_timing(struct mmc *mmc);
 static void set_wdog(struct mmc *mmc, u64 us);
 static void do_switch(struct mmc *mmc, union mio_emm_switch emm_switch);
 static int octeontx_mmc_send_cmd(struct mmc *mmc, struct mmc_cmd *cmd,
 				 struct mmc_data *data);
-static int octeontx2_mmc_calc_delay(struct mmc *mmc, int delay);
+static int octeontx_mmc_configure_delay(struct mmc *mmc);
 static int octeontx_mmc_calibrate_delay(struct mmc *mmc);
+#if !defined(CONFIG_ARCH_OCTEON)
+static int octeontx2_mmc_calc_delay(struct mmc *mmc, int delay);
+static void octeontx_mmc_set_timing(struct mmc *mmc);
 static int octeontx_mmc_set_input_bus_timing(struct mmc *mmc);
 static int octeontx_mmc_set_output_bus_timing(struct mmc *mmc);
+#endif
 
 static bool host_probed;
 
@@ -338,6 +347,7 @@
 }
 #endif
 
+#if !defined(CONFIG_ARCH_OCTEON)
 /**
  * Print out all of the register values where mmc is optional
  *
@@ -687,6 +697,12 @@
 	if (print)
 		octeontx_mmc_print_registers2(mmc, mmc_to_host(mmc));
 }
+#else
+static void octeontx_mmc_print_registers(struct mmc *mmc)
+{
+	return;
+}
+#endif
 
 static const struct octeontx_sd_mods octeontx_cr_types[] = {
 { {0, 0}, {0, 0}, {0, 0} },	/* CMD0 */
@@ -838,14 +854,17 @@
 		break;
 	case EXT_CSD_HS_TIMING:
 		slot->want_switch.s.hs_timing = 0;
+#if !defined(CONFIG_ARCH_OCTEON)
 		slot->want_switch.s.hs200_timing = 0;
 		slot->want_switch.s.hs400_timing = 0;
+#endif
 		switch (val & 0xf) {
 		case 0:
 			break;
 		case 1:
 			slot->want_switch.s.hs_timing = 1;
 			break;
+#if !defined(CONFIG_ARCH_OCTEON)
 		case 2:
 			if (!slot->is_asim && !slot->is_emul)
 				slot->want_switch.s.hs200_timing = 1;
@@ -854,6 +873,7 @@
 			if (!slot->is_asim && !slot->is_emul)
 				slot->want_switch.s.hs400_timing = 1;
 			break;
+#endif
 		default:
 			pr_err("%s(%s): Unsupported timing mode 0x%x\n",
 			       __func__, mmc->dev->name, val & 0xf);
@@ -2413,7 +2433,10 @@
 	struct octeontx_mmc_slot *slot = mmc_to_slot(mmc);
 	struct octeontx_mmc_host *host = slot->host;
 
-	return DIV_ROUND_UP(host->sys_freq, mmc->clock);
+	if (mmc->clock)
+		return DIV_ROUND_UP(host->sys_freq, mmc->clock);
+
+	return 0;
 }
 
 static int octeontx_mmc_set_ios(struct udevice *dev)
@@ -2489,14 +2512,18 @@
 	case UHS_SDR25:
 	case UHS_SDR50:
 	case UHS_SDR104:
+#if !defined(CONFIG_ARCH_OCTEON)
 		emm_switch.s.hs200_timing = 1;
+#endif
 		break;
 	case MMC_HS_400:
 		is_hs400 = true;
 		fallthrough;
 	case UHS_DDR50:
 	case MMC_DDR_52:
+#if !defined(CONFIG_ARCH_OCTEON)
 		emm_switch.s.hs400_timing = 1;
+#endif
 		break;
 	default:
 		pr_err("%s(%s): Unsupported mode 0x%x\n", __func__, dev->name,
@@ -2522,17 +2549,21 @@
 		      mmc->selected_mode);
 	}
 
+#if !defined(CONFIG_ARCH_OCTEON)
 	debug(" Trying switch 0x%llx w%d hs:%d hs200:%d hs400:%d\n",
 	      emm_switch.u, emm_switch.s.bus_width, emm_switch.s.hs_timing,
 	      emm_switch.s.hs200_timing, emm_switch.s.hs400_timing);
+#endif
 
 	set_wdog(mmc, 1000);
 	do_switch(mmc, emm_switch);
 	mdelay(100);
 	mode.u = read_csr(mmc, MIO_EMM_MODEX(slot->bus_id));
+#if !defined(CONFIG_ARCH_OCTEON)
 	debug("%s(%s): mode: 0x%llx w:%d, hs:%d, hs200:%d, hs400:%d\n",
 	      __func__, dev->name, mode.u, mode.s.bus_width,
 	      mode.s.hs_timing, mode.s.hs200_timing, mode.s.hs400_timing);
+#endif
 
 	err = octeontx_mmc_configure_delay(mmc);
 
@@ -2578,6 +2609,26 @@
 	return val;
 }
 
+#if defined(CONFIG_ARCH_OCTEON)
+static int octeontx_mmc_configure_delay(struct mmc *mmc)
+{
+	struct octeontx_mmc_slot *slot = mmc_to_slot(mmc);
+	union mio_emm_sample emm_sample;
+
+	debug("%s(%s)\n", __func__, mmc->dev->name);
+
+	emm_sample.u = 0;
+	emm_sample.s.cmd_cnt = slot->cmd_cnt;
+	emm_sample.s.dat_cnt = slot->dat_cnt;
+	write_csr(mmc, MIO_EMM_SAMPLE(), emm_sample.u);
+
+	return 0;
+}
+
+static void octeontx_mmc_io_drive_setup(struct mmc *mmc)
+{
+}
+#else
 static void octeontx_mmc_set_timing(struct mmc *mmc)
 {
 	union mio_emm_timing timing;
@@ -2613,7 +2664,8 @@
 
 	debug("%s(%s)\n", __func__, mmc->dev->name);
 
-	if (IS_ENABLED(CONFIG_ARCH_OCTEONTX)) {
+	if (IS_ENABLED(CONFIG_ARCH_OCTEON) ||
+	    IS_ENABLED(CONFIG_ARCH_OCTEONTX)) {
 		union mio_emm_sample emm_sample;
 
 		emm_sample.u = 0;
@@ -2760,6 +2812,28 @@
 }
 
 /**
+ * Set the IO drive strength and slew
+ *
+ * @param	mmc	mmc device
+ */
+static void octeontx_mmc_io_drive_setup(struct mmc *mmc)
+{
+	if (IS_ENABLED(CONFIG_ARCH_OCTEONTX2)) {
+		struct octeontx_mmc_slot *slot = mmc_to_slot(mmc);
+		union mio_emm_io_ctl io_ctl;
+
+		if (slot->drive < 0 || slot->slew < 0)
+			return;
+
+		io_ctl.u = 0;
+		io_ctl.s.drive = slot->drive;
+		io_ctl.s.slew = slot->slew;
+		write_csr(mmc, MIO_EMM_IO_CTL(), io_ctl.u);
+	}
+}
+#endif
+
+/**
  * Sets the MMC watchdog timer in microseconds
  *
  * @param	mmc	mmc device
@@ -2785,27 +2859,6 @@
 }
 
 /**
- * Set the IO drive strength and slew
- *
- * @param	mmc	mmc device
- */
-static void octeontx_mmc_io_drive_setup(struct mmc *mmc)
-{
-	if (!IS_ENABLED(CONFIG_ARCH_OCTEONTX)) {
-		struct octeontx_mmc_slot *slot = mmc_to_slot(mmc);
-		union mio_emm_io_ctl io_ctl;
-
-		if (slot->drive < 0 || slot->slew < 0)
-			return;
-
-		io_ctl.u = 0;
-		io_ctl.s.drive = slot->drive;
-		io_ctl.s.slew = slot->slew;
-		write_csr(mmc, MIO_EMM_IO_CTL(), io_ctl.u);
-	}
-}
-
-/**
  * Print switch errors
  *
  * @param	mmc	mmc device
@@ -2859,6 +2912,31 @@
 }
 
 /**
+ * Calibrates the delay based on the internal clock
+ *
+ * @param	mmc	Pointer to mmc data structure
+ *
+ * @return	0 for success or -ETIMEDOUT on error
+ *
+ * NOTE: On error a default value will be calculated.
+ */
+#if defined(CONFIG_ARCH_OCTEON)
+static int octeontx_mmc_set_input_bus_timing(struct mmc *mmc)
+{
+	return 0;
+}
+
+static int octeontx_mmc_set_output_bus_timing(struct mmc *mmc)
+{
+	return 0;
+}
+
+static int octeontx_mmc_calibrate_delay(struct mmc *mmc)
+{
+	return 0;
+}
+#else
+/**
  * Given a delay in ps, return the tap delay count
  *
  * @param	mmc	mmc data structure
@@ -2883,15 +2961,6 @@
 	return min_t(int, DIV_ROUND_UP(delay, host->timing_taps), 63);
 }
 
-/**
- * Calibrates the delay based on the internal clock
- *
- * @param	mmc	Pointer to mmc data structure
- *
- * @return	0 for success or -ETIMEDOUT on error
- *
- * NOTE: On error a default value will be calculated.
- */
 static int octeontx_mmc_calibrate_delay(struct mmc *mmc)
 {
 	union mio_emm_calb emm_calb;
@@ -3141,6 +3210,7 @@
 
 	return 0;
 }
+#endif
 
 static void octeontx_mmc_set_clock(struct mmc *mmc)
 {
@@ -3389,8 +3459,10 @@
 {
 	u32 volt = 0;
 
-	/* Convert to millivolts */
-	voltage /= 1000;
+	/* Convert to millivolts. Only necessary on ARM Octeon TX/TX2 */
+	if (!IS_ENABLED(CONFIG_ARCH_OCTEON))
+		voltage /= 1000;
+
 	if (voltage >= 1650 && voltage <= 1950)
 		volt |= MMC_VDD_165_195;
 	if (voltage >= 2000 && voltage <= 2100)
@@ -3736,6 +3808,8 @@
 {
 	struct octeontx_mmc_host *host = dev_get_priv(dev);
 	union mio_emm_int emm_int;
+	struct clk clk;
+	int ret;
 	u8 rev;
 
 	debug("%s(%s): Entry host: %p\n", __func__, dev->name, host);
@@ -3745,12 +3819,20 @@
 		return -ENODEV;
 	}
 	memset(host, 0, sizeof(*host));
-	host->base_addr = dm_pci_map_bar(dev, PCI_BASE_ADDRESS_0,
-					 PCI_REGION_MEM);
-	if (!host->base_addr) {
-		pr_err("%s: Error: MMC base address not found\n", __func__);
-		return -1;
+
+	/* Octeon TX & TX2 use PCI based probing */
+	if (device_is_compatible(dev, "cavium,thunder-8890-mmc")) {
+		host->base_addr = dm_pci_map_bar(dev, PCI_BASE_ADDRESS_0,
+						 PCI_REGION_MEM);
+		if (!host->base_addr) {
+			pr_err("%s: Error: MMC base address not found\n",
+			       __func__);
+			return -1;
+		}
+	} else {
+		host->base_addr = dev_remap_addr(dev);
 	}
+
 	host->dev = dev;
 	debug("%s(%s): Base address: %p\n", __func__, dev->name,
 	      host->base_addr);
@@ -3760,10 +3842,12 @@
 	}
 	host->node = dev_ofnode(dev);
 	host->last_slotid = -1;
+#if !defined(CONFIG_ARCH_OCTEON)
 	if (otx_is_platform(PLATFORM_ASIM))
 		host->is_asim = true;
 	if (otx_is_platform(PLATFORM_EMULATOR))
 		host->is_emul = true;
+#endif
 	host->dma_wait_delay =
 		ofnode_read_u32_default(dev_ofnode(dev),
 					"marvell,dma-wait-delay", 1);
@@ -3776,7 +3860,15 @@
 	writeq(emm_int.u, host->base_addr + MIO_EMM_INT());
 
 	debug("%s(%s): Getting I/O clock\n", __func__, dev->name);
-	host->sys_freq = octeontx_get_io_clock();
+	ret = clk_get_by_index(dev, 0, &clk);
+	if (ret < 0)
+		return ret;
+
+	ret = clk_enable(&clk);
+	if (ret)
+		return ret;
+
+	host->sys_freq = clk_get_rate(&clk);
 	debug("%s(%s): I/O clock %llu\n", __func__, dev->name, host->sys_freq);
 
 	if (IS_ENABLED(CONFIG_ARCH_OCTEONTX2)) {
@@ -3882,6 +3974,7 @@
 
 static const struct udevice_id octeontx_hsmmc_host_ids[] = {
 	{ .compatible = "cavium,thunder-8890-mmc" },
+	{ .compatible = "cavium,octeon-7360-mmc" },
 	{ }
 };
 
diff --git a/drivers/net/mscc_eswitch/jr2_switch.c b/drivers/net/mscc_eswitch/jr2_switch.c
index 128d7f2..570d5a5 100644
--- a/drivers/net/mscc_eswitch/jr2_switch.c
+++ b/drivers/net/mscc_eswitch/jr2_switch.c
@@ -235,7 +235,7 @@
 	"port36", "port37", "port38", "port39", "port40", "port41", "port42",
 	"port43", "port44", "port45", "port46", "port47",
 	"ana_ac", "ana_cl", "ana_l2", "asm", "hsio", "lrn",
-	"qfwd", "qs", "qsys", "rew",
+	"qfwd", "qs", "qsys", "rew", "gcb", "icpu",
 };
 
 #define REGS_NAMES_COUNT ARRAY_SIZE(regs_names) + 1
@@ -252,6 +252,8 @@
 	QS,
 	QSYS,
 	REW,
+	GCB,
+	ICPU,
 };
 
 #define JR2_MIIM_BUS_COUNT 3
@@ -367,7 +369,6 @@
 {
 	u32 ib_if_mode = 0;
 	u32 ib_qrate = 0;
-	u32 ib_cal_ena = 0;
 	u32 ib1_tsdet = 0;
 	u32 ob_lev = 0;
 	u32 ob_ena_cas = 0;
@@ -379,7 +380,6 @@
 	case PHY_INTERFACE_MODE_SGMII:
 		ib_if_mode = 1;
 		ib_qrate = 1;
-		ib_cal_ena = 1;
 		ib1_tsdet = 3;
 		ob_lev = 48;
 		ob_ena_cas = 2;
@@ -402,6 +402,12 @@
 	if (interface == PHY_INTERFACE_MODE_QSGMII)
 		writel(0xfff, base + HSIO_HW_CFGSTAT_HW_CFG);
 
+	writel(HSIO_ANA_SERDES6G_OB_CFG_RESISTOR_CTRL(1) |
+	       HSIO_ANA_SERDES6G_OB_CFG_SR(7) |
+	       HSIO_ANA_SERDES6G_OB_CFG_SR_H |
+	       HSIO_ANA_SERDES6G_OB_CFG_ENA1V_MODE(ob_ena1v_mode) |
+	       HSIO_ANA_SERDES6G_OB_CFG_POL, base + HSIO_ANA_SERDES6G_OB_CFG);
+
 	writel(HSIO_ANA_SERDES6G_COMMON_CFG_IF_MODE(3),
 	       base + HSIO_ANA_SERDES6G_COMMON_CFG);
 	writel(HSIO_ANA_SERDES6G_PLL_CFG_FSM_CTRL_DATA(120) |
@@ -431,6 +437,21 @@
 	       HSIO_ANA_SERDES6G_IB_CFG1_TSDET(3) |
 	       HSIO_ANA_SERDES6G_IB_CFG1_TJTAG(8),
 	       base + HSIO_ANA_SERDES6G_IB_CFG1);
+
+	writel(HSIO_ANA_SERDES6G_IB_CFG2_UREG(4) |
+	       HSIO_ANA_SERDES6G_IB_CFG2_UMAX(2) |
+	       HSIO_ANA_SERDES6G_IB_CFG2_TCALV(12) |
+	       HSIO_ANA_SERDES6G_IB_CFG2_OCALS(32) |
+	       HSIO_ANA_SERDES6G_IB_CFG2_OINFS(7) |
+	       HSIO_ANA_SERDES6G_IB_CFG2_OINFI(0x1f) |
+	       HSIO_ANA_SERDES6G_IB_CFG2_TINFV(3),
+	       base + HSIO_ANA_SERDES6G_IB_CFG2);
+
+	writel(HSIO_ANA_SERDES6G_IB_CFG3_INI_OFFSET(0x1f) |
+	       HSIO_ANA_SERDES6G_IB_CFG3_INI_LP(1) |
+	       HSIO_ANA_SERDES6G_IB_CFG3_INI_MID(0x1f),
+	       base + HSIO_ANA_SERDES6G_IB_CFG3);
+
 	writel(HSIO_DIG_SERDES6G_MISC_CFG_LANE_RST,
 	       base + HSIO_DIG_SERDES6G_MISC_CFG);
 
@@ -505,7 +526,7 @@
 	writel(HSIO_ANA_SERDES6G_IB_CFG_REG_ENA |
 	       HSIO_ANA_SERDES6G_IB_CFG_EQZ_ENA |
 	       HSIO_ANA_SERDES6G_IB_CFG_SAM_ENA |
-	       HSIO_ANA_SERDES6G_IB_CFG_CAL_ENA(ib_cal_ena) |
+	       HSIO_ANA_SERDES6G_IB_CFG_CAL_ENA(1) |
 	       HSIO_ANA_SERDES6G_IB_CFG_CONCUR |
 	       HSIO_ANA_SERDES6G_IB_CFG_SIG_DET_ENA |
 	       HSIO_ANA_SERDES6G_IB_CFG_REG_PAT_SEL_OFF(0) |
@@ -530,7 +551,7 @@
 	writel(HSIO_ANA_SERDES6G_IB_CFG_REG_ENA |
 	       HSIO_ANA_SERDES6G_IB_CFG_EQZ_ENA |
 	       HSIO_ANA_SERDES6G_IB_CFG_SAM_ENA |
-	       HSIO_ANA_SERDES6G_IB_CFG_CAL_ENA(ib_cal_ena) |
+	       HSIO_ANA_SERDES6G_IB_CFG_CAL_ENA(1) |
 	       HSIO_ANA_SERDES6G_IB_CFG_CONCUR |
 	       HSIO_ANA_SERDES6G_IB_CFG_SIG_DET_ENA |
 	       HSIO_ANA_SERDES6G_IB_CFG_REG_PAT_SEL_OFF(0) |
@@ -850,6 +871,7 @@
 	struct mii_dev *bus;
 	struct ofnode_phandle_args phandle;
 	struct phy_device *phy;
+	u32 val;
 
 	if (!priv)
 		return -EINVAL;
@@ -865,6 +887,17 @@
 		}
 	}
 
+	val = readl(priv->regs[ICPU] + ICPU_RESET);
+	val |= ICPU_RESET_CORE_RST_PROTECT;
+	writel(val, priv->regs[ICPU] + ICPU_RESET);
+
+	val = readl(priv->regs[GCB] + PERF_SOFT_RST);
+	val |= PERF_SOFT_RST_SOFT_SWC_RST;
+	writel(val, priv->regs[GCB] + PERF_SOFT_RST);
+
+	while (readl(priv->regs[GCB] + PERF_SOFT_RST) & PERF_SOFT_RST_SOFT_SWC_RST)
+		;
+
 	/* Initialize miim buses */
 	memset(&miim, 0x0, sizeof(struct mscc_miim_dev) * JR2_MIIM_BUS_COUNT);