include/configs: Use new CONFIG_CMD_* in various s* named board config files.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
diff --git a/include/configs/spieval.h b/include/configs/spieval.h
index 9888d11..e480df5 100644
--- a/include/configs/spieval.h
+++ b/include/configs/spieval.h
@@ -44,11 +44,6 @@
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
/*
* Serial console configuration
*/
@@ -88,12 +83,6 @@
#define CONFIG_NS8382X 1
#endif /* CONFIG_STK52XX */
-#ifdef CONFIG_PCI
-#define ADD_PCI_CMD CFG_CMD_PCI
-#else
-#define ADD_PCI_CMD 0
-#endif
-
/*
* Video console
*/
@@ -110,12 +99,6 @@
#define CFG_CONSOLE_IS_IN_ENV
#endif
-#ifdef CONFIG_VIDEO
-#define ADD_BMP_CMD CFG_CMD_BMP
-#else
-#define ADD_BMP_CMD 0
-#endif
-
/* Partitions */
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
@@ -124,10 +107,7 @@
/* USB */
#ifdef CONFIG_STK52XX
#define CONFIG_USB_OHCI
-#define ADD_USB_CMD CFG_CMD_USB | CFG_CMD_FAT
#define CONFIG_USB_STORAGE
-#else
-#define ADD_USB_CMD 0
#endif
/* POST support */
@@ -143,36 +123,44 @@
#define CFG_CMD_POST_DIAG 0
#endif
-/* IDE */
-#if defined (CONFIG_MINIFAP) || defined (CONFIG_STK52XX)
-#define ADD_IDE_CMD (CFG_CMD_IDE | CFG_CMD_FAT | CFG_CMD_EXT2)
-#else
-#define ADD_IDE_CMD 0
-#endif
/*
- * Supported commands
+ * Command line configuration.
*/
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- ADD_BMP_CMD | \
- ADD_IDE_CMD | \
- ADD_PCI_CMD | \
- ADD_USB_CMD | \
- CFG_CMD_ASKENV | \
- CFG_CMD_DATE | \
- CFG_CMD_DHCP | \
- CFG_CMD_ECHO | \
- CFG_CMD_EEPROM | \
- CFG_CMD_I2C | \
- CFG_CMD_MII | \
- CFG_CMD_NFS | \
- CFG_CMD_PING | \
- CFG_CMD_POST_DIAG | \
- CFG_CMD_REGINFO | \
- CFG_CMD_SNTP )
+#include <config_cmd_default.h>
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+#if defined(CONFIG_MINIFAP) || defined(CONFIG_STK52XX)
+ #define CONFIG_CMD_IDE
+ #define CONFIG_CMD_FAT
+ #define CONFIG_CMD_EXT2
+#endif
+
+#ifdef CONFIG_STK52XX
+ #define CONFIG_CMD_USB
+ #define CONFIG_CMD_FAT
+#endif
+
+#ifdef CONFIG_VIDEO
+ #define CONFIG_CMD_BMP
+#endif
+
+#ifdef CONFIG_PCI
+ #define CONFIG_CMD_PCI
+#endif
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ECHO
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_POST
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SNTP
+
#define CONFIG_TIMESTAMP /* display image timestamps */
@@ -406,7 +394,7 @@
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
@@ -425,6 +413,11 @@
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
+#if defined(CONFIG_CMD_KGDB)
+# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
/*
* Enable loopw commando. This has only affect, if CFG_CMD_MEM is defined,
* which is normally part of the default commands (CFV_CMD_DFL)