diff --git a/Makefile b/Makefile
index 53ad450..fa7aa89 100644
--- a/Makefile
+++ b/Makefile
@@ -909,6 +909,26 @@
 u-boot-with-spl.bin: spl/u-boot-spl.bin $(SPL_PAYLOAD) FORCE
 	$(call if_changed,pad_cat)
 
+MKIMAGEFLAGS_lpc32xx-spl.img = -T lpc32xximage -a $(CONFIG_SPL_TEXT_BASE)
+
+lpc32xx-spl.img: spl/u-boot-spl.bin FORCE
+	$(call if_changed,mkimage)
+
+OBJCOPYFLAGS_lpc32xx-boot-0.bin = -I binary -O binary --pad-to=$(CONFIG_SPL_PAD_TO)
+
+lpc32xx-boot-0.bin: lpc32xx-spl.img
+	$(call if_changed,objcopy)
+
+OBJCOPYFLAGS_lpc32xx-boot-1.bin = -I binary -O binary --pad-to=$(CONFIG_SPL_PAD_TO)
+
+lpc32xx-boot-1.bin: lpc32xx-spl.img
+	$(call if_changed,objcopy)
+
+lpc32xx-full.bin: lpc32xx-boot-0.bin lpc32xx-boot-1.bin u-boot.img
+	$(call if_changed,cat)
+
+CLEAN_FILES += lpc32xx-*
+
 OBJCOPYFLAGS_u-boot-with-tpl.bin = -I binary -O binary \
 				   --pad-to=$(CONFIG_TPL_PAD_TO)
 tpl/u-boot-with-tpl.bin: tpl/u-boot-tpl.bin u-boot.bin FORCE
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 80b0d34..086ca85 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -132,6 +132,11 @@
 	bool "Support devkit3250"
 	select CPU_ARM926EJS
 
+config TARGET_WORK_92105
+	bool "Support work_92105"
+	select CPU_ARM926EJS
+	select SUPPORT_SPL
+
 config TARGET_MX25PDK
 	bool "Support mx25pdk"
 	select CPU_ARM926EJS
@@ -872,6 +877,7 @@
 source "board/wandboard/Kconfig"
 source "board/warp/Kconfig"
 source "board/woodburn/Kconfig"
+source "board/work-microwave/work_92105/Kconfig"
 source "board/xaeniax/Kconfig"
 source "board/xilinx/zynqmp/Kconfig"
 source "board/zipitz2/Kconfig"
diff --git a/arch/arm/cpu/arm926ejs/lpc32xx/Makefile b/arch/arm/cpu/arm926ejs/lpc32xx/Makefile
index 314f004..4837377 100644
--- a/arch/arm/cpu/arm926ejs/lpc32xx/Makefile
+++ b/arch/arm/cpu/arm926ejs/lpc32xx/Makefile
@@ -6,3 +6,5 @@
 #
 
 obj-y   = cpu.o clk.o devices.o timer.o
+
+obj-$(CONFIG_SPL_BUILD) += dram.o lowlevel_init.o
diff --git a/arch/arm/cpu/arm926ejs/lpc32xx/clk.c b/arch/arm/cpu/arm926ejs/lpc32xx/clk.c
index b7a44d5..1ef8a36 100644
--- a/arch/arm/cpu/arm926ejs/lpc32xx/clk.c
+++ b/arch/arm/cpu/arm926ejs/lpc32xx/clk.c
@@ -98,6 +98,40 @@
 	return get_hclk_pll_rate() / get_periph_clk_div();
 }
 
+unsigned int get_sdram_clk_rate(void)
+{
+	unsigned int src_clk;
+
+	if (!(readl(&clk->pwr_ctrl) & CLK_PWR_NORMAL_RUN))
+		return get_sys_clk_rate();
+
+	src_clk = get_hclk_pll_rate();
+
+	if (readl(&clk->sdramclk_ctrl) & CLK_SDRAM_DDR_SEL) {
+		/* using DDR */
+		switch (readl(&clk->hclkdiv_ctrl) & CLK_HCLK_DDRAM_MASK) {
+		case CLK_HCLK_DDRAM_HALF:
+			return src_clk/2;
+		case CLK_HCLK_DDRAM_NOMINAL:
+			return src_clk;
+		default:
+			return 0;
+		}
+	} else {
+		/* using SDR */
+		switch (readl(&clk->hclkdiv_ctrl) & CLK_HCLK_ARM_PLL_DIV_MASK) {
+		case CLK_HCLK_ARM_PLL_DIV_4:
+			return src_clk/4;
+		case CLK_HCLK_ARM_PLL_DIV_2:
+			return src_clk/2;
+		case CLK_HCLK_ARM_PLL_DIV_1:
+			return src_clk;
+		default:
+			return 0;
+		}
+	}
+}
+
 int get_serial_clock(void)
 {
 	return get_periph_clk_rate();
diff --git a/arch/arm/cpu/arm926ejs/lpc32xx/cpu.c b/arch/arm/cpu/arm926ejs/lpc32xx/cpu.c
index eec4d9e..f757474 100644
--- a/arch/arm/cpu/arm926ejs/lpc32xx/cpu.c
+++ b/arch/arm/cpu/arm926ejs/lpc32xx/cpu.c
@@ -9,6 +9,7 @@
 #include <asm/arch/cpu.h>
 #include <asm/arch/clk.h>
 #include <asm/arch/wdt.h>
+#include <asm/arch/sys_proto.h>
 #include <asm/io.h>
 
 static struct clk_pm_regs *clk = (struct clk_pm_regs *)CLK_PM_BASE;
diff --git a/arch/arm/cpu/arm926ejs/lpc32xx/dram.c b/arch/arm/cpu/arm926ejs/lpc32xx/dram.c
new file mode 100644
index 0000000..1eea8e2
--- /dev/null
+++ b/arch/arm/cpu/arm926ejs/lpc32xx/dram.c
@@ -0,0 +1,77 @@
+/*
+ * LPC32xx dram init
+ *
+ * (C) Copyright 2014  DENX Software Engineering GmbH
+ * Written-by: Albert ARIBAUD <albert.aribaud@3adev.fr>
+ *
+ * This is called by SPL to gain access to the SDR DRAM.
+ *
+ * This code runs from SRAM.
+ *
+ * Actual CONFIG_LPC32XX_SDRAM_* parameters must be provided
+ * by the board configuration file.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <netdev.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/clk.h>
+#include <asm/arch/wdt.h>
+#include <asm/arch/emc.h>
+#include <asm/io.h>
+
+static struct clk_pm_regs *clk = (struct clk_pm_regs *)CLK_PM_BASE;
+static struct emc_regs *emc = (struct emc_regs *)EMC_BASE;
+
+void ddr_init(struct emc_dram_settings *dram)
+{
+	uint32_t ck;
+
+	/* Enable EMC interface and choose little endian mode */
+	writel(1, &emc->ctrl);
+	writel(0, &emc->config);
+	/* Select maximum EMC Dynamic Memory Refresh Time */
+	writel(0x7FF, &emc->refresh);
+	/* Determine CLK */
+	ck = get_sdram_clk_rate();
+	/* Configure SDRAM */
+	writel(dram->cmddelay, &clk->sdramclk_ctrl);
+	writel(dram->config0, &emc->config0);
+	writel(dram->rascas0, &emc->rascas0);
+	writel(dram->rdconfig, &emc->read_config);
+	/* Set timings */
+	writel((ck / dram->trp) & 0x0000000F, &emc->t_rp);
+	writel((ck / dram->tras) & 0x0000000F, &emc->t_ras);
+	writel((ck / dram->tsrex) & 0x0000007F, &emc->t_srex);
+	writel((ck / dram->twr) & 0x0000000F, &emc->t_wr);
+	writel((ck / dram->trc) & 0x0000001F, &emc->t_rc);
+	writel((ck / dram->trfc) & 0x0000001F, &emc->t_rfc);
+	writel((ck / dram->txsr) & 0x000000FF, &emc->t_xsr);
+	writel(dram->trrd, &emc->t_rrd);
+	writel(dram->tmrd, &emc->t_mrd);
+	writel(dram->tcdlr, &emc->t_cdlr);
+	/* Dynamic refresh */
+	writel((((ck / dram->refresh) >> 4) & 0x7FF), &emc->refresh);
+	udelay(10);
+	/* Force all clocks, enable inverted ck, issue NOP command */
+	writel(0x00000193, &emc->control);
+	udelay(100);
+	/* Keep all clocks enabled, issue a PRECHARGE ALL command */
+	writel(0x00000113, &emc->control);
+	/* Fast dynamic refresh for at least a few SDRAM ck cycles */
+	writel((((128) >> 4) & 0x7FF), &emc->refresh);
+	udelay(10);
+	/* set correct dynamic refresh timing */
+	writel((((ck / dram->refresh) >> 4) & 0x7FF), &emc->refresh);
+	udelay(10);
+	/* set normal mode to CAS=3 */
+	writel(0x00000093, &emc->control);
+	readl(EMC_DYCS0_BASE | dram->mode);
+	/* set extended mode to all zeroes */
+	writel(0x00000093, &emc->control);
+	readl(EMC_DYCS0_BASE | dram->emode);
+	/* stop forcing clocks, keep inverted clock, issue normal mode */
+	writel(0x00000010, &emc->control);
+}
diff --git a/arch/arm/cpu/arm926ejs/lpc32xx/lowlevel_init.S b/arch/arm/cpu/arm926ejs/lpc32xx/lowlevel_init.S
new file mode 100644
index 0000000..4b8053e
--- /dev/null
+++ b/arch/arm/cpu/arm926ejs/lpc32xx/lowlevel_init.S
@@ -0,0 +1,45 @@
+/*
+ * WORK Microwave work_92105 board low level init
+ *
+ * (C) Copyright 2014  DENX Software Engineering GmbH
+ * Written-by: Albert ARIBAUD <albert.aribaud@3adev.fr>
+ *
+ * Low level init is called from SPL to set up the clocks.
+ * On entry, the LPC3250 is in Direct Run mode with all clocks
+ * running at 13 MHz; on exit, ARM clock is 208 MHz, HCLK is
+ * 104 MHz and PCLK is 13 MHz.
+ *
+ * This code must run from SRAM so that the clock changes do
+ * not prevent it from executing.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+.globl lowlevel_init
+
+lowlevel_init:
+
+	/* Set ARM, HCLK, PCLK dividers for normal mode */
+	ldr	r0, =0x0000003D
+	ldr	r1, =0x40004040
+	str	r0, [r1]
+
+	/* Start HCLK PLL for 208 MHz */
+	ldr	r0, =0x0001401E
+	ldr	r1, =0x40004058
+	str	r0, [r1]
+
+	/* wait for HCLK PLL to lock */
+1:
+	ldr	r0, [r1]
+	ands	r0, r0, #1
+	beq	1b
+
+	/* switch to normal mode */
+	ldr	r1, =0x40004044
+	ldr	r0, [r1]
+	orr	r0, #0x00000004
+	str	r0, [r1]
+
+	/* Return to U-boot via saved link register */
+	mov	pc, lr
diff --git a/arch/arm/include/asm/arch-lpc32xx/clk.h b/arch/arm/include/asm/arch-lpc32xx/clk.h
index 2cb5703..9449869 100644
--- a/arch/arm/include/asm/arch-lpc32xx/clk.h
+++ b/arch/arm/include/asm/arch-lpc32xx/clk.h
@@ -71,6 +71,7 @@
 };
 
 /* HCLK Divider Control Register bits */
+#define CLK_HCLK_DDRAM_MASK		(0x3 << 7)
 #define CLK_HCLK_DDRAM_HALF		(0x2 << 7)
 #define CLK_HCLK_DDRAM_NOMINAL		(0x1 << 7)
 #define CLK_HCLK_DDRAM_STOPPED		(0x0 << 7)
@@ -158,11 +159,15 @@
 /* SSP Clock Control Register bits */
 #define CLK_SSP0_ENABLE_CLOCK		(1 << 0)
 
+/* SDRAMCLK register bits */
+#define CLK_SDRAM_DDR_SEL		(1 << 1)
+
 unsigned int get_sys_clk_rate(void);
 unsigned int get_hclk_pll_rate(void);
 unsigned int get_hclk_clk_div(void);
 unsigned int get_hclk_clk_rate(void);
 unsigned int get_periph_clk_div(void);
 unsigned int get_periph_clk_rate(void);
+unsigned int get_sdram_clk_rate(void);
 
 #endif /* _LPC32XX_CLK_H */
diff --git a/arch/arm/include/asm/arch-lpc32xx/cpu.h b/arch/arm/include/asm/arch-lpc32xx/cpu.h
index 1067107..0b5dca1 100644
--- a/arch/arm/include/asm/arch-lpc32xx/cpu.h
+++ b/arch/arm/include/asm/arch-lpc32xx/cpu.h
@@ -27,6 +27,7 @@
 #define HS_UART7_BASE	0x4001C000	/* High speed UART 7 registers base */
 #define RTC_BASE	0x40024000	/* RTC registers base               */
 #define GPIO_BASE	0x40028000	/* GPIO registers base              */
+#define MUX_BASE	0x40028100	/* MUX registers base               */
 #define WDT_BASE	0x4003C000	/* Watchdog timer registers base    */
 #define TIMER0_BASE	0x40044000	/* Timer0 registers base            */
 #define TIMER1_BASE	0x4004C000	/* Timer1 registers base            */
diff --git a/arch/arm/include/asm/arch-lpc32xx/emc.h b/arch/arm/include/asm/arch-lpc32xx/emc.h
index 82d9bcc..1a2bab2 100644
--- a/arch/arm/include/asm/arch-lpc32xx/emc.h
+++ b/arch/arm/include/asm/arch-lpc32xx/emc.h
@@ -76,4 +76,25 @@
 #define EMC_STAT_WAITWR(n)		(((n) - 2) & 0x1F)
 #define EMC_STAT_WAITTURN(n)		(((n) - 1) & 0x0F)
 
+/* EMC settings for DRAM */
+struct emc_dram_settings {
+	u32	cmddelay;
+	u32	config0;
+	u32	rascas0;
+	u32	rdconfig;
+	u32	trp;
+	u32	tras;
+	u32	tsrex;
+	u32	twr;
+	u32	trc;
+	u32	trfc;
+	u32	txsr;
+	u32	trrd;
+	u32	tmrd;
+	u32	tcdlr;
+	u32	refresh;
+	u32	mode;
+	u32	emode;
+};
+
 #endif /* _LPC32XX_EMC_H */
diff --git a/arch/arm/include/asm/arch-lpc32xx/mux.h b/arch/arm/include/asm/arch-lpc32xx/mux.h
new file mode 100644
index 0000000..dc1b5bc
--- /dev/null
+++ b/arch/arm/include/asm/arch-lpc32xx/mux.h
@@ -0,0 +1,18 @@
+/*
+ * LPC32xx MUX interface
+ *
+ * (C) Copyright 2015  DENX Software Engineering GmbH
+ * Written-by: Albert ARIBAUD <albert.aribaud@3adev.fr>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+/**
+ * MUX register map for LPC32xx
+ */
+
+struct mux_regs {
+	u32 p_mux_set;
+	u32 p_mux_clr;
+	u32 p_mux_state;
+};
diff --git a/arch/arm/include/asm/arch-lpc32xx/sys_proto.h b/arch/arm/include/asm/arch-lpc32xx/sys_proto.h
index 86d5ee9..c3d890d 100644
--- a/arch/arm/include/asm/arch-lpc32xx/sys_proto.h
+++ b/arch/arm/include/asm/arch-lpc32xx/sys_proto.h
@@ -7,10 +7,14 @@
 #ifndef _LPC32XX_SYS_PROTO_H
 #define _LPC32XX_SYS_PROTO_H
 
+#include <asm/arch/emc.h>
+
 void lpc32xx_uart_init(unsigned int uart_id);
 void lpc32xx_mac_init(void);
 void lpc32xx_mlc_nand_init(void);
 void lpc32xx_i2c_init(unsigned int devnum);
 void lpc32xx_ssp_init(void);
-
+#if defined(CONFIG_SPL_BUILD)
+void ddr_init(const struct emc_dram_settings *dram);
+#endif
 #endif /* _LPC32XX_SYS_PROTO_H */
diff --git a/board/work-microwave/work_92105/Kconfig b/board/work-microwave/work_92105/Kconfig
new file mode 100644
index 0000000..74f004f
--- /dev/null
+++ b/board/work-microwave/work_92105/Kconfig
@@ -0,0 +1,15 @@
+if TARGET_WORK_92105
+
+config SYS_BOARD
+	default "work_92105"
+
+config SYS_VENDOR
+	default "work-microwave"
+
+config SYS_SOC
+	default "lpc32xx"
+
+config SYS_CONFIG_NAME
+	default "work_92105"
+
+endif
diff --git a/board/work-microwave/work_92105/MAINTAINERS b/board/work-microwave/work_92105/MAINTAINERS
new file mode 100644
index 0000000..29a92c5
--- /dev/null
+++ b/board/work-microwave/work_92105/MAINTAINERS
@@ -0,0 +1,6 @@
+WORK_92105 BOARD
+M:	Albert ARIBAUD <albert.aribaud@3adev.fr>
+S:	Maintained
+F:	board/work-microwave/work_92105/
+F:	include/configs/work_92105.h
+F:	configs/work_92105_defconfig
diff --git a/board/work-microwave/work_92105/Makefile b/board/work-microwave/work_92105/Makefile
new file mode 100644
index 0000000..ba31c8e
--- /dev/null
+++ b/board/work-microwave/work_92105/Makefile
@@ -0,0 +1,10 @@
+#
+# (C) Copyright 2014  DENX Software Engineering GmbH
+# Written-by: Albert ARIBAUD <albert.aribaud@3adev.fr>
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y	:= work_92105.o work_92105_display.o
+
+obj-$(CONFIG_SPL_BUILD) += work_92105_spl.o
diff --git a/board/work-microwave/work_92105/README b/board/work-microwave/work_92105/README
new file mode 100644
index 0000000..3c256e0
--- /dev/null
+++ b/board/work-microwave/work_92105/README
@@ -0,0 +1,91 @@
+Work_92105 from Work Microwave is an LPC3250- based board with the
+following features:
+
+    - 64MB SDR DRAM
+    - 1 GB SLC NAND, managed through MLC controller.
+    - Ethernet
+    - Ethernet + PHY SMSC8710
+    - I2C:
+      - EEPROM (24M01-compatible)
+      - RTC (DS1374-compatible)
+      - Temperature sensor (DS620)
+      - DACs (2 x MAX518)
+    - SPI (through SSP interface)
+      - Port expander MAX6957
+    - LCD display (HD44780-compatible), controlled
+      through the port expander and DACs
+
+Standard SPL and U-Boot binaries
+--------------------------------
+
+The default 'make' (or the 'make all') command will produce the
+following files:
+
+1. spl/u-boot-spl.bin	SPL, intended to run from SRAM at address 0.
+			This file can be loaded in SRAM through a JTAG
+			debugger or through the LPC32XX Service Boot
+			mechanism.
+
+2. u-boot.bin		The raw U-Boot image, which can be loaded in
+			DDR through a JTAG debugger (for instance by
+			breaking SPL after DDR init), or by a running
+			U-Boot through e.g. 'loady' or 'tftp' and then
+			executed with 'go'.
+
+3. u-boot.img		A U-Boot image with a mkimage header prepended.
+			SPL assumes (even when loaded through JTAG or
+			Service Boot) that such an image will be found
+			at offset 0x00040000 in NAND.
+
+NAND cold-boot binaries
+-----------------------
+
+The board can boot entirely from power-on with only SPL and U-Boot in
+NAND. The LPC32XX-specific 'make lpc32xx-full.bin' command will produce
+(in addition to spl/u-boot-spl.bin and u-boot.img if they were not made
+already) the following files:
+
+4. lpc32xx-spl.img	spl/u-boot-spl.bin, with a LPC32XX boot header
+			prepended. This header is required for the ROM
+			code to load SPL into SRAM and branch into it.
+			The content of this file is expected to reside
+			in NAND at addresses 0x00000000 and 0x00020000
+			(two copies).
+
+5. lpc32xx-boot-0.bin	lpc32xx-spl.img, padded with 0xFF bytes to a
+			size of 0x20000 bytes. This file covers exactly
+			the reserved area for the first bootloader copy
+			in NAND.
+
+6. lpc32xx-boot-1.bin	Same as lpc32xx-boot-0.bin. This is intended to
+			be used as the second bootloader copy.
+
+7. lpc32xx-full.bin	lpc32xx-boot-0.bin, lpc32xx-boot-1.bin and
+			u-boot.img concatenated. This file represents
+			the content of whole bootloader as present in
+			NAND at offset 00x00000000.
+
+Flashing instructions
+---------------------
+
+The following assumes a working U-Boot on the target, with the ability
+to load files into DDR.
+
+To update the whole bootloader:
+
+	nand erase 0x00000000 0x80000
+	(load lpc32xx-full.bin at location $loadaddr)
+	nand write $loadaddr 0x00000000 $filesize
+
+To update SPL only (note the double nand write) :
+
+	nand erase 0x00000000 0x40000
+	(load lpc32xx-spl.img or lpc32xx-boot-N.bin at location $loadaddr)
+	nand write $loadaddr 0x00000000 $filesize
+	nand write $loadaddr 0x00020000 $filesize
+
+To update U-Boot only:
+
+	nand erase 0x00040000 0x40000
+	(load u-boot.img at location $loadaddr)
+	nand write $loadaddr 0x00040000 $filesize
diff --git a/board/work-microwave/work_92105/work_92105.c b/board/work-microwave/work_92105/work_92105.c
new file mode 100644
index 0000000..f782284
--- /dev/null
+++ b/board/work-microwave/work_92105/work_92105.c
@@ -0,0 +1,77 @@
+/*
+ * WORK Microwave work_92105 board support
+ *
+ * (C) Copyright 2014  DENX Software Engineering GmbH
+ * Written-by: Albert ARIBAUD <albert.aribaud@3adev.fr>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/clk.h>
+#include <asm/arch/emc.h>
+#include <asm/arch/wdt.h>
+#include <asm/gpio.h>
+#include <spl.h>
+#include "work_92105_display.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static struct clk_pm_regs *clk = (struct clk_pm_regs *)CLK_PM_BASE;
+static struct wdt_regs  *wdt = (struct wdt_regs *)WDT_BASE;
+
+void reset_periph(void)
+{
+	setbits_le32(&clk->timclk_ctrl, CLK_TIMCLK_WATCHDOG);
+	writel(WDTIM_MCTRL_RESFRC1, &wdt->mctrl);
+	udelay(150);
+	writel(0, &wdt->mctrl);
+	clrbits_le32(&clk->timclk_ctrl, CLK_TIMCLK_WATCHDOG);
+}
+
+int board_early_init_f(void)
+{
+	/* initialize serial port for console */
+	lpc32xx_uart_init(CONFIG_SYS_LPC32XX_UART);
+	/* enable I2C, SSP, MAC, NAND */
+	lpc32xx_i2c_init(1); /* only I2C1 has devices, I2C2 has none */
+	lpc32xx_ssp_init();
+	lpc32xx_mac_init();
+	lpc32xx_mlc_nand_init();
+	/* Display must wait until after relocation and devices init */
+	return 0;
+}
+
+#define GPO_19 115
+
+int board_early_init_r(void)
+{
+	/* Set NAND !WP to 1 through GPO_19 */
+	gpio_request(GPO_19, "NAND_nWP");
+	gpio_direction_output(GPO_19, 1);
+
+	/* initialize display */
+	work_92105_display_init();
+
+	return 0;
+}
+
+int board_init(void)
+{
+	reset_periph();
+	/* adress of boot parameters */
+	gd->bd->bi_boot_params  = CONFIG_SYS_SDRAM_BASE + 0x100;
+
+	return 0;
+}
+
+int dram_init(void)
+{
+	gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
+				    CONFIG_SYS_SDRAM_SIZE);
+
+	return 0;
+}
diff --git a/board/work-microwave/work_92105/work_92105_display.c b/board/work-microwave/work_92105/work_92105_display.c
new file mode 100644
index 0000000..c8b1013
--- /dev/null
+++ b/board/work-microwave/work_92105/work_92105_display.c
@@ -0,0 +1,349 @@
+/*
+ * work_92105 display support
+ *
+ * (C) Copyright 2014  DENX Software Engineering GmbH
+ * Written-by: Albert ARIBAUD <albert.aribaud@3adev.fr>
+ *
+ * The work_92105 display is a HD44780-compatible module
+ * controlled through a MAX6957AAX SPI port expander, two
+ * MAX518 I2C DACs and native LPC32xx GPO 15.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/emc.h>
+#include <asm/gpio.h>
+#include <spi.h>
+#include <i2c.h>
+#include <version.h>
+#include <vsprintf.h>
+
+/*
+ * GPO 15 in port 3 is gpio 3*32+15 = 111
+ */
+
+#define GPO_15 111
+
+/**
+ * MAX6957AAX registers that we will be using
+ */
+
+#define MAX6957_CONF		0x04
+
+#define MAX6957_CONF_08_11	0x0A
+#define MAX6957_CONF_12_15	0x0B
+#define MAX6957_CONF_16_19	0x0C
+
+/**
+ * Individual gpio ports (one per gpio) to HD44780
+ */
+
+#define MAX6957AAX_HD44780_RS	0x29
+#define MAX6957AAX_HD44780_R_W	0x2A
+#define MAX6957AAX_HD44780_EN	0x2B
+#define MAX6957AAX_HD44780_DATA	0x4C
+
+/**
+ * Display controller instructions
+ */
+
+/* Function set: eight bits, two lines, 8-dot font */
+#define HD44780_FUNCTION_SET		0x38
+
+/* Display ON / OFF: turn display on */
+#define HD44780_DISPLAY_ON_OFF_CONTROL	0x0C
+
+/* Entry mode: increment */
+#define HD44780_ENTRY_MODE_SET		0x06
+
+/* Clear */
+#define HD44780_CLEAR_DISPLAY		0x01
+
+/* Set DDRAM addr (to be ORed with exact address) */
+#define HD44780_SET_DDRAM_ADDR		0x80
+
+/* Set CGRAM addr (to be ORed with exact address) */
+#define HD44780_SET_CGRAM_ADDR		0x40
+
+/**
+ * Default value for contrats
+ */
+
+#define CONTRAST_DEFAULT  25
+
+/**
+ * Define slave as a module-wide local to save passing it around,
+ * plus we will need it after init for the "hd44780" command.
+ */
+
+static struct spi_slave *slave;
+
+/*
+ * Write a value into a MAX6957AAX register.
+ */
+
+static void max6957aax_write(uint8_t reg, uint8_t value)
+{
+	uint8_t dout[2];
+
+	dout[0] = reg;
+	dout[1] = value;
+	gpio_set_value(GPO_15, 0);
+	/* do SPI read/write (passing din==dout is OK) */
+	spi_xfer(slave, 16, dout, dout, SPI_XFER_BEGIN | SPI_XFER_END);
+	gpio_set_value(GPO_15, 1);
+}
+
+/*
+ * Read a value from a MAX6957AAX register.
+ *
+ * According to the MAX6957AAX datasheet, we should release the chip
+ * select halfway through the read sequence, when the actual register
+ * value is read; but the WORK_92105 hardware prevents the MAX6957AAX
+ * SPI OUT from reaching the LPC32XX SIP MISO if chip is not selected.
+ * so let's release the CS an hold it again while reading the result.
+ */
+
+static uint8_t max6957aax_read(uint8_t reg)
+{
+	uint8_t dout[2], din[2];
+
+	/* send read command */
+	dout[0] = reg | 0x80; /* set bit 7 to indicate read */
+	dout[1] = 0;
+	gpio_set_value(GPO_15, 0);
+	/* do SPI read/write (passing din==dout is OK) */
+	spi_xfer(slave, 16, dout, dout, SPI_XFER_BEGIN | SPI_XFER_END);
+	/* latch read command */
+	gpio_set_value(GPO_15, 1);
+	/* read register -- din = noop on xmit, din[1] = reg on recv */
+	din[0] = 0;
+	din[1] = 0;
+	gpio_set_value(GPO_15, 0);
+	/* do SPI read/write (passing din==dout is OK) */
+	spi_xfer(slave, 16, din, din, SPI_XFER_BEGIN | SPI_XFER_END);
+	/* end of read. */
+	gpio_set_value(GPO_15, 1);
+	return din[1];
+}
+
+static void hd44780_instruction(unsigned long instruction)
+{
+	max6957aax_write(MAX6957AAX_HD44780_RS, 0);
+	max6957aax_write(MAX6957AAX_HD44780_R_W, 0);
+	max6957aax_write(MAX6957AAX_HD44780_EN, 1);
+	max6957aax_write(MAX6957AAX_HD44780_DATA, instruction);
+	max6957aax_write(MAX6957AAX_HD44780_EN, 0);
+	/* HD44780 takes 37 us for most instructions, 1520 for clear */
+	if (instruction == HD44780_CLEAR_DISPLAY)
+		udelay(2000);
+	else
+		udelay(100);
+}
+
+static void hd44780_write_char(char c)
+{
+	max6957aax_write(MAX6957AAX_HD44780_RS, 1);
+	max6957aax_write(MAX6957AAX_HD44780_R_W, 0);
+	max6957aax_write(MAX6957AAX_HD44780_EN, 1);
+	max6957aax_write(MAX6957AAX_HD44780_DATA, c);
+	max6957aax_write(MAX6957AAX_HD44780_EN, 0);
+	/* HD44780 takes 37 us to write to DDRAM or CGRAM */
+	udelay(100);
+}
+
+static void hd44780_write_str(char *s)
+{
+	max6957aax_write(MAX6957AAX_HD44780_RS, 1);
+	max6957aax_write(MAX6957AAX_HD44780_R_W, 0);
+	while (*s) {
+		max6957aax_write(MAX6957AAX_HD44780_EN, 1);
+		max6957aax_write(MAX6957AAX_HD44780_DATA, *s);
+		max6957aax_write(MAX6957AAX_HD44780_EN, 0);
+		s++;
+		/* HD44780 takes 37 us to write to DDRAM or CGRAM */
+		udelay(100);
+	}
+}
+
+/*
+ * Existing user code might expect these custom characters to be
+ * recognized and displayed on the LCD
+ */
+
+static u8 char_gen_chars[] = {
+	/* #8, empty rectangle */
+	0x1F, 0x11, 0x11, 0x11, 0x11, 0x11, 0x11, 0x1F,
+	/* #9, filled right arrow */
+	0x10, 0x18, 0x1C, 0x1E, 0x1C, 0x18, 0x10, 0x00,
+	/* #10, filled left arrow */
+	0x01, 0x03, 0x07, 0x0F, 0x07, 0x03, 0x01, 0x00,
+	/* #11, up and down arrow */
+	0x04, 0x0E, 0x1F, 0x00, 0x00, 0x1F, 0x0E, 0x04,
+	/* #12, plus/minus */
+	0x04, 0x04, 0x1F, 0x04, 0x04, 0x00, 0x1F, 0x00,
+	/* #13, fat exclamation mark */
+	0x06, 0x06, 0x06, 0x06, 0x00, 0x06, 0x06, 0x00,
+	/* #14, empty square */
+	0x00, 0x1F, 0x11, 0x11, 0x11, 0x1F, 0x00, 0x00,
+	/* #15, struck out square */
+	0x00, 0x1F, 0x19, 0x15, 0x13, 0x1F, 0x00, 0x00,
+};
+
+static void hd44780_init_char_gen(void)
+{
+	int i;
+
+	hd44780_instruction(HD44780_SET_CGRAM_ADDR);
+
+	for (i = 0; i < sizeof(char_gen_chars); i++)
+		hd44780_write_char(char_gen_chars[i]);
+
+	hd44780_instruction(HD44780_SET_DDRAM_ADDR);
+}
+
+void work_92105_display_init(void)
+{
+	int claim_err;
+	char *display_contrast_str;
+	uint8_t display_contrast = CONTRAST_DEFAULT;
+	uint8_t enable_backlight = 0x96;
+
+	slave = spi_setup_slave(0, 0, 500000, 0);
+
+	if (!slave) {
+		printf("Failed to set up SPI slave\n");
+		return;
+	}
+
+	claim_err = spi_claim_bus(slave);
+
+	if (claim_err)
+		debug("Failed to claim SPI bus: %d\n", claim_err);
+
+	/* enable backlight */
+	i2c_write(0x2c, 0x01, 1, &enable_backlight, 1);
+
+	/* set display contrast */
+	display_contrast_str = getenv("fwopt_dispcontrast");
+	if (display_contrast_str)
+		display_contrast = simple_strtoul(display_contrast_str,
+			NULL, 10);
+	i2c_write(0x2c, 0x00, 1, &display_contrast, 1);
+
+	/* request GPO_15 as an output initially set to 1 */
+	gpio_request(GPO_15, "MAX6957_nCS");
+	gpio_direction_output(GPO_15, 1);
+
+	/* enable MAX6957 portexpander */
+	max6957aax_write(MAX6957_CONF, 0x01);
+	/* configure pin 8 as input, pins 9..19 as outputs */
+	max6957aax_write(MAX6957_CONF_08_11, 0x56);
+	max6957aax_write(MAX6957_CONF_12_15, 0x55);
+	max6957aax_write(MAX6957_CONF_16_19, 0x55);
+
+	/* initialize HD44780 */
+	max6957aax_write(MAX6957AAX_HD44780_EN, 0);
+	hd44780_instruction(HD44780_FUNCTION_SET);
+	hd44780_instruction(HD44780_DISPLAY_ON_OFF_CONTROL);
+	hd44780_instruction(HD44780_ENTRY_MODE_SET);
+
+	/* write custom character glyphs */
+	hd44780_init_char_gen();
+
+	/* Show U-Boot version, date and time as a sign-of-life */
+	hd44780_instruction(HD44780_CLEAR_DISPLAY);
+	hd44780_instruction(HD44780_SET_DDRAM_ADDR | 0);
+	hd44780_write_str(U_BOOT_VERSION);
+	hd44780_instruction(HD44780_SET_DDRAM_ADDR | 64);
+	hd44780_write_str(U_BOOT_DATE);
+	hd44780_instruction(HD44780_SET_DDRAM_ADDR | 64 | 20);
+	hd44780_write_str(U_BOOT_TIME);
+}
+
+#ifdef CONFIG_CMD_MAX6957
+
+static int do_max6957aax(cmd_tbl_t *cmdtp, int flag, int argc,
+			 char *const argv[])
+{
+	int reg, val;
+
+	if (argc != 3)
+		return CMD_RET_USAGE;
+	switch (argv[1][0]) {
+	case 'r':
+	case 'R':
+		reg = simple_strtoul(argv[2], NULL, 0);
+		val = max6957aax_read(reg);
+		printf("MAX6957 reg 0x%02x read 0x%02x\n", reg, val);
+		return 0;
+	default:
+		reg = simple_strtoul(argv[1], NULL, 0);
+		val = simple_strtoul(argv[2], NULL, 0);
+		max6957aax_write(reg, val);
+		printf("MAX6957 reg 0x%02x wrote 0x%02x\n", reg, val);
+		return 0;
+	}
+	return 1;
+}
+
+#ifdef CONFIG_SYS_LONGHELP
+static char max6957aax_help_text[] =
+	"max6957aax - write or read display register:\n"
+		"\tmax6957aax R|r reg - read display register;\n"
+		"\tmax6957aax reg val - write display register.";
+#endif
+
+U_BOOT_CMD(
+	max6957aax, 6, 1, do_max6957aax,
+	"SPI MAX6957 display write/read",
+	max6957aax_help_text
+);
+#endif /* CONFIG_CMD_MAX6957 */
+
+#ifdef CONFIG_CMD_HD44760
+
+/*
+ * We need the HUSH parser because we need string arguments, and
+ * only HUSH can understand them.
+ */
+
+#if !defined(CONFIG_SYS_HUSH_PARSER)
+#error CONFIG_CMD_HD44760 requires CONFIG_SYS_HUSH_PARSER
+#endif
+
+static int do_hd44780(cmd_tbl_t *cmdtp, int flag, int argc, char *const argv[])
+{
+	char *cmd;
+
+	if (argc != 3)
+		return CMD_RET_USAGE;
+
+	cmd = argv[1];
+
+	if (strcasecmp(cmd, "cmd") == 0)
+		hd44780_instruction(simple_strtol(argv[2], NULL, 0));
+	else if (strcasecmp(cmd, "data") == 0)
+		hd44780_write_char(simple_strtol(argv[2], NULL, 0));
+	else if (strcasecmp(cmd, "str") == 0)
+		hd44780_write_str(argv[2]);
+	return 0;
+}
+
+#ifdef CONFIG_SYS_LONGHELP
+static char hd44780_help_text[] =
+	"hd44780 - control LCD driver:\n"
+		"\thd44780 cmd <val> - send command <val> to driver;\n"
+		"\thd44780 data <val> - send data <val> to driver;\n"
+		"\thd44780 str \"<text>\" - send \"<text>\" to driver.";
+#endif
+
+U_BOOT_CMD(
+	hd44780, 6, 1, do_hd44780,
+	"HD44780 LCD driver control",
+	hd44780_help_text
+);
+#endif /* CONFIG_CMD_HD44780 */
diff --git a/board/work-microwave/work_92105/work_92105_display.h b/board/work-microwave/work_92105/work_92105_display.h
new file mode 100644
index 0000000..dd6e768
--- /dev/null
+++ b/board/work-microwave/work_92105/work_92105_display.h
@@ -0,0 +1,14 @@
+/*
+ * work_92105 display support interface
+ *
+ * (C) Copyright 2014  DENX Software Engineering GmbH
+ * Written-by: Albert ARIBAUD <albert.aribaud@3adev.fr>
+ *
+ * The work_92105 display is a HD44780-compatible module
+ * controlled through a MAX6957AAX SPI port expander, two
+ * MAX518 I2C DACs and native LPC32xx GPO 15.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+void work_92105_display_init(void);
diff --git a/board/work-microwave/work_92105/work_92105_spl.c b/board/work-microwave/work_92105/work_92105_spl.c
new file mode 100644
index 0000000..282a6dd
--- /dev/null
+++ b/board/work-microwave/work_92105/work_92105_spl.c
@@ -0,0 +1,85 @@
+/*
+ * WORK Microwave work_92105 board support
+ *
+ * (C) Copyright 2014  DENX Software Engineering GmbH
+ * Written-by: Albert ARIBAUD <albert.aribaud@3adev.fr>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/io.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/emc.h>
+#include <asm/gpio.h>
+#include <spl.h>
+#include "work_92105_display.h"
+
+struct emc_dram_settings dram_64mb = {
+	.cmddelay = 0x0001C000,
+	.config0 = 0x00005682,
+	.rascas0 = 0x00000302,
+	.rdconfig = 0x00000011,
+	.trp = 52631578,
+	.tras = 20833333,
+	.tsrex = 12500000,
+	.twr = 66666666,
+	.trc = 13888888,
+	.trfc = 10256410,
+	.txsr = 12500000,
+	.trrd = 1,
+	.tmrd = 1,
+	.tcdlr = 0,
+	.refresh = 128000,
+	.mode = 0x00018000,
+	.emode = 0x02000000
+};
+
+const struct emc_dram_settings dram_128mb = {
+	.cmddelay = 0x0001C000,
+	.config0 = 0x00005882,
+	.rascas0 = 0x00000302,
+	.rdconfig = 0x00000011,
+	.trp = 52631578,
+	.tras = 22222222,
+	.tsrex = 8333333,
+	.twr = 66666666,
+	.trc = 14814814,
+	.trfc = 10256410,
+	.txsr = 8333333,
+	.trrd = 1,
+	.tmrd = 1,
+	.tcdlr = 0,
+	.refresh = 128000,
+	.mode = 0x00030000,
+	.emode = 0x02000000
+};
+
+void spl_board_init(void)
+{
+	/* initialize serial port for console */
+	lpc32xx_uart_init(CONFIG_SYS_LPC32XX_UART);
+	/* initialize console */
+	preloader_console_init();
+	/* init DDR and NAND to chainload U-Boot */
+	ddr_init(&dram_128mb);
+	/*
+	 * If this is actually a 64MB module, then the highest column
+	 * bit in any address will be ignored, and thus address 0x80000000
+	 * should be mirrored at address 0x80000800. Test this.
+	 */
+	writel(0x31415926, 0x80000000); /* write Pi at 0x80000000 */
+	writel(0x16180339, 0x80000800); /* write Phi at 0x80000800 */
+	if (readl(0x80000000) == 0x16180339) /* check 0x80000000 */ {
+		/* actually 64MB mirrored: reconfigure controller */
+		ddr_init(&dram_64mb);
+	}
+	/* initialize NAND controller to load U-Boot from NAND */
+	lpc32xx_mlc_nand_init();
+}
+
+u32 spl_boot_device(void)
+{
+	return BOOT_DEVICE_NAND;
+}
diff --git a/configs/work_92105_defconfig b/configs/work_92105_defconfig
new file mode 100644
index 0000000..142a505
--- /dev/null
+++ b/configs/work_92105_defconfig
@@ -0,0 +1,6 @@
+CONFIG_ARM=y
+CONFIG_TARGET_WORK_92105=y
+CONFIG_DM=y
+CONFIG_DM_GPIO=y
+CONFIG_SPL=y
+CONFIG_SYS_EXTRA_OPTIONS=""
diff --git a/include/configs/work_92105.h b/include/configs/work_92105.h
new file mode 100644
index 0000000..dc8e99f
--- /dev/null
+++ b/include/configs/work_92105.h
@@ -0,0 +1,241 @@
+/*
+ * WORK Microwave work_92105 board configuration file
+ *
+ * (C) Copyright 2014  DENX Software Engineering GmbH
+ * Written-by: Albert ARIBAUD <albert.aribaud@3adev.fr>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __CONFIG_WORK_92105_H__
+#define __CONFIG_WORK_92105_H__
+
+/* SoC and board defines */
+#include <linux/sizes.h>
+#include <asm/arch/cpu.h>
+
+/*
+ * Define work_92105 machine type by hand -- done only for compatibility
+ * with original board code
+ */
+#define MACH_TYPE_WORK_92105		736
+#define CONFIG_MACH_TYPE		MACH_TYPE_WORK_92105
+
+#define CONFIG_SYS_ICACHE_OFF
+#define CONFIG_SYS_DCACHE_OFF
+#if !defined(CONFIG_SPL_BUILD)
+#define CONFIG_SKIP_LOWLEVEL_INIT
+#endif
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_BOARD_EARLY_INIT_R
+
+/* generate LPC32XX-specific SPL image */
+#define CONFIG_LPC32XX_SPL
+
+/*
+ * Memory configurations
+ */
+#define CONFIG_NR_DRAM_BANKS		1
+#define CONFIG_SYS_MALLOC_LEN		SZ_1M
+#define CONFIG_SYS_SDRAM_BASE		EMC_DYCS0_BASE
+#define CONFIG_SYS_SDRAM_SIZE		SZ_128M
+#define CONFIG_SYS_TEXT_BASE		0x80100000
+#define CONFIG_SYS_MEMTEST_START	(CONFIG_SYS_SDRAM_BASE + SZ_32K)
+#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_TEXT_BASE - SZ_1M)
+
+#define CONFIG_SYS_LOAD_ADDR		(CONFIG_SYS_SDRAM_BASE + SZ_32K)
+
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_SDRAM_BASE + SZ_512K \
+					 - GENERATED_GBL_DATA_SIZE)
+
+/*
+ * Serial Driver
+ */
+#define CONFIG_SYS_LPC32XX_UART		5   /* UART5 - NS16550 */
+#define CONFIG_BAUDRATE			115200
+
+/*
+ * Ethernet Driver
+ */
+
+#define CONFIG_PHY_SMSC
+#define CONFIG_LPC32XX_ETH
+#define CONFIG_PHYLIB
+#define CONFIG_PHY_ADDR 0
+#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+/* FIXME: remove "Waiting for PHY auto negotiation to complete..." message */
+
+/*
+ * I2C driver
+ */
+
+#define CONFIG_SYS_I2C_LPC32XX
+#define CONFIG_SYS_I2C
+#define CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C_SPEED 350000
+
+/*
+ * I2C EEPROM
+ */
+
+#define CONFIG_CMD_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x56
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
+
+/*
+ * I2C RTC
+ */
+
+#define CONFIG_CMD_DATE
+#define CONFIG_RTC_DS1374
+
+/*
+ * I2C Temperature Sensor (DTT)
+ */
+
+#define CONFIG_CMD_DTT
+#define CONFIG_DTT_SENSORS { 0, 1 }
+#define CONFIG_DTT_DS620
+
+/*
+ * U-Boot General Configurations
+ */
+#define CONFIG_SYS_GENERIC_BOARD
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_CBSIZE		1024
+#define CONFIG_SYS_PBSIZE		\
+	(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
+#define CONFIG_SYS_MAXARGS		16
+#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
+
+#define CONFIG_SYS_HUSH_PARSER
+
+#define CONFIG_AUTO_COMPLETE
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_VERSION_VARIABLE
+#define CONFIG_DISPLAY_CPUINFO
+#define CONFIG_DOS_PARTITION
+
+/*
+ * No NOR
+ */
+
+#define CONFIG_SYS_NO_FLASH
+
+/*
+ * NAND chip timings for FIXME: which one?
+ */
+
+#define CONFIG_LPC32XX_NAND_MLC_TCEA_DELAY  333333333
+#define CONFIG_LPC32XX_NAND_MLC_BUSY_DELAY   10000000
+#define CONFIG_LPC32XX_NAND_MLC_NAND_TA      18181818
+#define CONFIG_LPC32XX_NAND_MLC_RD_HIGH      31250000
+#define CONFIG_LPC32XX_NAND_MLC_RD_LOW       45454545
+#define CONFIG_LPC32XX_NAND_MLC_WR_HIGH      40000000
+#define CONFIG_LPC32XX_NAND_MLC_WR_LOW       83333333
+
+/*
+ * NAND
+ */
+
+/* driver configuration */
+#define CONFIG_SYS_NAND_SELF_INIT
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define CONFIG_SYS_MAX_NAND_CHIPS 1
+#define CONFIG_SYS_NAND_BASE MLC_NAND_BASE
+#define CONFIG_NAND_LPC32XX_MLC
+
+#define CONFIG_CMD_NAND
+
+/*
+ * GPIO
+ */
+
+#define CONFIG_CMD_GPIO
+#define CONFIG_LPC32XX_GPIO
+
+/*
+ * SSP/SPI/DISPLAY
+ */
+
+#define CONFIG_CMD_SPI
+#define CONFIG_LPC32XX_SSP
+#define CONFIG_LPC32XX_SSP_TIMEOUT 100000
+#define CONFIG_CMD_MAX6957
+#define CONFIG_CMD_HD44760
+/*
+ * Environment
+ */
+
+#define CONFIG_ENV_IS_IN_NAND		1
+#define CONFIG_ENV_SIZE			0x00020000
+#define CONFIG_ENV_OFFSET		0x00100000
+#define CONFIG_ENV_OFFSET_REDUND	0x00120000
+#define CONFIG_ENV_ADDR			0x80000100
+
+/*
+ * Provide default ethernet address
+ *
+ * THIS IS NORMALLY NOT DONE. HERE WE KEEP WHAT WAS IN THE PORTED
+ * BOARD CONFIG IN CASE SOME PROVISIONING PROCESS OUT THERE EXPECTS
+ * THIS MAC ADDRESS WHEN THE DEVICE HAS STILL ITS DEFAULT CONFIG.
+ */
+
+#define CONFIG_ETHADDR			00:12:B4:00:AF:FE
+#define	CONFIG_OVERWRITE_ETHADDR_ONCE
+
+/*
+ * U-Boot Commands
+ */
+#include <config_cmd_default.h>
+
+/*
+ * Boot Linux
+ */
+#define CONFIG_CMDLINE_TAG
+#define CONFIG_SETUP_MEMORY_TAGS
+#define CONFIG_INITRD_TAG
+
+#define CONFIG_ZERO_BOOTDELAY_CHECK
+#define CONFIG_BOOTDELAY		3
+
+#define CONFIG_BOOTFILE			"uImage"
+#define CONFIG_BOOTARGS			"console=ttyS2,115200n8"
+#define CONFIG_LOADADDR			0x80008000
+
+/*
+ * SPL
+ */
+
+/* SPL will be executed at offset 0 */
+#define CONFIG_SPL_TEXT_BASE 0x00000000
+/* SPL will use SRAM as stack */
+#define CONFIG_SPL_STACK     0x0000FFF8
+#define CONFIG_SPL_BOARD_INIT
+/* Use the framework and generic lib */
+#define CONFIG_SPL_FRAMEWORK
+#define CONFIG_SPL_LIBGENERIC_SUPPORT
+#define CONFIG_SPL_LIBCOMMON_SUPPORT
+/* SPL will use serial */
+#define CONFIG_SPL_SERIAL_SUPPORT
+/* SPL will load U-Boot from NAND offset 0x40000 */
+#define CONFIG_SPL_NAND_SUPPORT
+#define CONFIG_SPL_NAND_DRIVERS
+#define CONFIG_SPL_NAND_BASE
+#define CONFIG_SPL_NAND_BOOT
+#define CONFIG_SYS_NAND_U_BOOT_OFFS  0x00040000
+#define CONFIG_SPL_PAD_TO 0x20000
+/* U-Boot will be 0x40000 bytes, loaded and run at CONFIG_SYS_TEXT_BASE */
+#define CONFIG_SYS_MONITOR_LEN 0x40000 /* actually, MAX size */
+#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_NAND_U_BOOT_DST   CONFIG_SYS_TEXT_BASE
+
+/*
+ * Include SoC specific configuration
+ */
+#include <asm/arch/config.h>
+
+#endif  /* __CONFIG_WORK_92105_H__*/