lpc32xx: add support for board work_92105
Work_92105 from Work Microwave is an LPC3250-
based board with the following features:
- 64MB or 128MB SDR DRAM
- 1 GB SLC NAND, managed through MLC controller.
- Ethernet
- Ethernet + PHY SMSC8710
- I2C:
- EEPROM (24M01-compatible)
- RTC (DS1374-compatible)
- Temperature sensor (DS620)
- DACs (2 x MAX518)
- SPI (through SSP interface)
- Port expander MAX6957
- LCD display (HD44780-compatible), controlled
through the port expander and DACs
This board has SPL support, and uses the LPC32XX boot
image format.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 80b0d34..086ca85 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -132,6 +132,11 @@
bool "Support devkit3250"
select CPU_ARM926EJS
+config TARGET_WORK_92105
+ bool "Support work_92105"
+ select CPU_ARM926EJS
+ select SUPPORT_SPL
+
config TARGET_MX25PDK
bool "Support mx25pdk"
select CPU_ARM926EJS
@@ -872,6 +877,7 @@
source "board/wandboard/Kconfig"
source "board/warp/Kconfig"
source "board/woodburn/Kconfig"
+source "board/work-microwave/work_92105/Kconfig"
source "board/xaeniax/Kconfig"
source "board/xilinx/zynqmp/Kconfig"
source "board/zipitz2/Kconfig"
diff --git a/arch/arm/cpu/arm926ejs/lpc32xx/Makefile b/arch/arm/cpu/arm926ejs/lpc32xx/Makefile
index 314f004..4837377 100644
--- a/arch/arm/cpu/arm926ejs/lpc32xx/Makefile
+++ b/arch/arm/cpu/arm926ejs/lpc32xx/Makefile
@@ -6,3 +6,5 @@
#
obj-y = cpu.o clk.o devices.o timer.o
+
+obj-$(CONFIG_SPL_BUILD) += dram.o lowlevel_init.o
diff --git a/arch/arm/cpu/arm926ejs/lpc32xx/clk.c b/arch/arm/cpu/arm926ejs/lpc32xx/clk.c
index b7a44d5..1ef8a36 100644
--- a/arch/arm/cpu/arm926ejs/lpc32xx/clk.c
+++ b/arch/arm/cpu/arm926ejs/lpc32xx/clk.c
@@ -98,6 +98,40 @@
return get_hclk_pll_rate() / get_periph_clk_div();
}
+unsigned int get_sdram_clk_rate(void)
+{
+ unsigned int src_clk;
+
+ if (!(readl(&clk->pwr_ctrl) & CLK_PWR_NORMAL_RUN))
+ return get_sys_clk_rate();
+
+ src_clk = get_hclk_pll_rate();
+
+ if (readl(&clk->sdramclk_ctrl) & CLK_SDRAM_DDR_SEL) {
+ /* using DDR */
+ switch (readl(&clk->hclkdiv_ctrl) & CLK_HCLK_DDRAM_MASK) {
+ case CLK_HCLK_DDRAM_HALF:
+ return src_clk/2;
+ case CLK_HCLK_DDRAM_NOMINAL:
+ return src_clk;
+ default:
+ return 0;
+ }
+ } else {
+ /* using SDR */
+ switch (readl(&clk->hclkdiv_ctrl) & CLK_HCLK_ARM_PLL_DIV_MASK) {
+ case CLK_HCLK_ARM_PLL_DIV_4:
+ return src_clk/4;
+ case CLK_HCLK_ARM_PLL_DIV_2:
+ return src_clk/2;
+ case CLK_HCLK_ARM_PLL_DIV_1:
+ return src_clk;
+ default:
+ return 0;
+ }
+ }
+}
+
int get_serial_clock(void)
{
return get_periph_clk_rate();
diff --git a/arch/arm/cpu/arm926ejs/lpc32xx/cpu.c b/arch/arm/cpu/arm926ejs/lpc32xx/cpu.c
index eec4d9e..f757474 100644
--- a/arch/arm/cpu/arm926ejs/lpc32xx/cpu.c
+++ b/arch/arm/cpu/arm926ejs/lpc32xx/cpu.c
@@ -9,6 +9,7 @@
#include <asm/arch/cpu.h>
#include <asm/arch/clk.h>
#include <asm/arch/wdt.h>
+#include <asm/arch/sys_proto.h>
#include <asm/io.h>
static struct clk_pm_regs *clk = (struct clk_pm_regs *)CLK_PM_BASE;
diff --git a/arch/arm/cpu/arm926ejs/lpc32xx/dram.c b/arch/arm/cpu/arm926ejs/lpc32xx/dram.c
new file mode 100644
index 0000000..1eea8e2
--- /dev/null
+++ b/arch/arm/cpu/arm926ejs/lpc32xx/dram.c
@@ -0,0 +1,77 @@
+/*
+ * LPC32xx dram init
+ *
+ * (C) Copyright 2014 DENX Software Engineering GmbH
+ * Written-by: Albert ARIBAUD <albert.aribaud@3adev.fr>
+ *
+ * This is called by SPL to gain access to the SDR DRAM.
+ *
+ * This code runs from SRAM.
+ *
+ * Actual CONFIG_LPC32XX_SDRAM_* parameters must be provided
+ * by the board configuration file.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <netdev.h>
+#include <asm/arch/cpu.h>
+#include <asm/arch/clk.h>
+#include <asm/arch/wdt.h>
+#include <asm/arch/emc.h>
+#include <asm/io.h>
+
+static struct clk_pm_regs *clk = (struct clk_pm_regs *)CLK_PM_BASE;
+static struct emc_regs *emc = (struct emc_regs *)EMC_BASE;
+
+void ddr_init(struct emc_dram_settings *dram)
+{
+ uint32_t ck;
+
+ /* Enable EMC interface and choose little endian mode */
+ writel(1, &emc->ctrl);
+ writel(0, &emc->config);
+ /* Select maximum EMC Dynamic Memory Refresh Time */
+ writel(0x7FF, &emc->refresh);
+ /* Determine CLK */
+ ck = get_sdram_clk_rate();
+ /* Configure SDRAM */
+ writel(dram->cmddelay, &clk->sdramclk_ctrl);
+ writel(dram->config0, &emc->config0);
+ writel(dram->rascas0, &emc->rascas0);
+ writel(dram->rdconfig, &emc->read_config);
+ /* Set timings */
+ writel((ck / dram->trp) & 0x0000000F, &emc->t_rp);
+ writel((ck / dram->tras) & 0x0000000F, &emc->t_ras);
+ writel((ck / dram->tsrex) & 0x0000007F, &emc->t_srex);
+ writel((ck / dram->twr) & 0x0000000F, &emc->t_wr);
+ writel((ck / dram->trc) & 0x0000001F, &emc->t_rc);
+ writel((ck / dram->trfc) & 0x0000001F, &emc->t_rfc);
+ writel((ck / dram->txsr) & 0x000000FF, &emc->t_xsr);
+ writel(dram->trrd, &emc->t_rrd);
+ writel(dram->tmrd, &emc->t_mrd);
+ writel(dram->tcdlr, &emc->t_cdlr);
+ /* Dynamic refresh */
+ writel((((ck / dram->refresh) >> 4) & 0x7FF), &emc->refresh);
+ udelay(10);
+ /* Force all clocks, enable inverted ck, issue NOP command */
+ writel(0x00000193, &emc->control);
+ udelay(100);
+ /* Keep all clocks enabled, issue a PRECHARGE ALL command */
+ writel(0x00000113, &emc->control);
+ /* Fast dynamic refresh for at least a few SDRAM ck cycles */
+ writel((((128) >> 4) & 0x7FF), &emc->refresh);
+ udelay(10);
+ /* set correct dynamic refresh timing */
+ writel((((ck / dram->refresh) >> 4) & 0x7FF), &emc->refresh);
+ udelay(10);
+ /* set normal mode to CAS=3 */
+ writel(0x00000093, &emc->control);
+ readl(EMC_DYCS0_BASE | dram->mode);
+ /* set extended mode to all zeroes */
+ writel(0x00000093, &emc->control);
+ readl(EMC_DYCS0_BASE | dram->emode);
+ /* stop forcing clocks, keep inverted clock, issue normal mode */
+ writel(0x00000010, &emc->control);
+}
diff --git a/arch/arm/cpu/arm926ejs/lpc32xx/lowlevel_init.S b/arch/arm/cpu/arm926ejs/lpc32xx/lowlevel_init.S
new file mode 100644
index 0000000..4b8053e
--- /dev/null
+++ b/arch/arm/cpu/arm926ejs/lpc32xx/lowlevel_init.S
@@ -0,0 +1,45 @@
+/*
+ * WORK Microwave work_92105 board low level init
+ *
+ * (C) Copyright 2014 DENX Software Engineering GmbH
+ * Written-by: Albert ARIBAUD <albert.aribaud@3adev.fr>
+ *
+ * Low level init is called from SPL to set up the clocks.
+ * On entry, the LPC3250 is in Direct Run mode with all clocks
+ * running at 13 MHz; on exit, ARM clock is 208 MHz, HCLK is
+ * 104 MHz and PCLK is 13 MHz.
+ *
+ * This code must run from SRAM so that the clock changes do
+ * not prevent it from executing.
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+.globl lowlevel_init
+
+lowlevel_init:
+
+ /* Set ARM, HCLK, PCLK dividers for normal mode */
+ ldr r0, =0x0000003D
+ ldr r1, =0x40004040
+ str r0, [r1]
+
+ /* Start HCLK PLL for 208 MHz */
+ ldr r0, =0x0001401E
+ ldr r1, =0x40004058
+ str r0, [r1]
+
+ /* wait for HCLK PLL to lock */
+1:
+ ldr r0, [r1]
+ ands r0, r0, #1
+ beq 1b
+
+ /* switch to normal mode */
+ ldr r1, =0x40004044
+ ldr r0, [r1]
+ orr r0, #0x00000004
+ str r0, [r1]
+
+ /* Return to U-boot via saved link register */
+ mov pc, lr
diff --git a/arch/arm/include/asm/arch-lpc32xx/clk.h b/arch/arm/include/asm/arch-lpc32xx/clk.h
index 2cb5703..9449869 100644
--- a/arch/arm/include/asm/arch-lpc32xx/clk.h
+++ b/arch/arm/include/asm/arch-lpc32xx/clk.h
@@ -71,6 +71,7 @@
};
/* HCLK Divider Control Register bits */
+#define CLK_HCLK_DDRAM_MASK (0x3 << 7)
#define CLK_HCLK_DDRAM_HALF (0x2 << 7)
#define CLK_HCLK_DDRAM_NOMINAL (0x1 << 7)
#define CLK_HCLK_DDRAM_STOPPED (0x0 << 7)
@@ -158,11 +159,15 @@
/* SSP Clock Control Register bits */
#define CLK_SSP0_ENABLE_CLOCK (1 << 0)
+/* SDRAMCLK register bits */
+#define CLK_SDRAM_DDR_SEL (1 << 1)
+
unsigned int get_sys_clk_rate(void);
unsigned int get_hclk_pll_rate(void);
unsigned int get_hclk_clk_div(void);
unsigned int get_hclk_clk_rate(void);
unsigned int get_periph_clk_div(void);
unsigned int get_periph_clk_rate(void);
+unsigned int get_sdram_clk_rate(void);
#endif /* _LPC32XX_CLK_H */
diff --git a/arch/arm/include/asm/arch-lpc32xx/cpu.h b/arch/arm/include/asm/arch-lpc32xx/cpu.h
index 1067107..0b5dca1 100644
--- a/arch/arm/include/asm/arch-lpc32xx/cpu.h
+++ b/arch/arm/include/asm/arch-lpc32xx/cpu.h
@@ -27,6 +27,7 @@
#define HS_UART7_BASE 0x4001C000 /* High speed UART 7 registers base */
#define RTC_BASE 0x40024000 /* RTC registers base */
#define GPIO_BASE 0x40028000 /* GPIO registers base */
+#define MUX_BASE 0x40028100 /* MUX registers base */
#define WDT_BASE 0x4003C000 /* Watchdog timer registers base */
#define TIMER0_BASE 0x40044000 /* Timer0 registers base */
#define TIMER1_BASE 0x4004C000 /* Timer1 registers base */
diff --git a/arch/arm/include/asm/arch-lpc32xx/emc.h b/arch/arm/include/asm/arch-lpc32xx/emc.h
index 82d9bcc..1a2bab2 100644
--- a/arch/arm/include/asm/arch-lpc32xx/emc.h
+++ b/arch/arm/include/asm/arch-lpc32xx/emc.h
@@ -76,4 +76,25 @@
#define EMC_STAT_WAITWR(n) (((n) - 2) & 0x1F)
#define EMC_STAT_WAITTURN(n) (((n) - 1) & 0x0F)
+/* EMC settings for DRAM */
+struct emc_dram_settings {
+ u32 cmddelay;
+ u32 config0;
+ u32 rascas0;
+ u32 rdconfig;
+ u32 trp;
+ u32 tras;
+ u32 tsrex;
+ u32 twr;
+ u32 trc;
+ u32 trfc;
+ u32 txsr;
+ u32 trrd;
+ u32 tmrd;
+ u32 tcdlr;
+ u32 refresh;
+ u32 mode;
+ u32 emode;
+};
+
#endif /* _LPC32XX_EMC_H */
diff --git a/arch/arm/include/asm/arch-lpc32xx/mux.h b/arch/arm/include/asm/arch-lpc32xx/mux.h
new file mode 100644
index 0000000..dc1b5bc
--- /dev/null
+++ b/arch/arm/include/asm/arch-lpc32xx/mux.h
@@ -0,0 +1,18 @@
+/*
+ * LPC32xx MUX interface
+ *
+ * (C) Copyright 2015 DENX Software Engineering GmbH
+ * Written-by: Albert ARIBAUD <albert.aribaud@3adev.fr>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+/**
+ * MUX register map for LPC32xx
+ */
+
+struct mux_regs {
+ u32 p_mux_set;
+ u32 p_mux_clr;
+ u32 p_mux_state;
+};
diff --git a/arch/arm/include/asm/arch-lpc32xx/sys_proto.h b/arch/arm/include/asm/arch-lpc32xx/sys_proto.h
index 86d5ee9..c3d890d 100644
--- a/arch/arm/include/asm/arch-lpc32xx/sys_proto.h
+++ b/arch/arm/include/asm/arch-lpc32xx/sys_proto.h
@@ -7,10 +7,14 @@
#ifndef _LPC32XX_SYS_PROTO_H
#define _LPC32XX_SYS_PROTO_H
+#include <asm/arch/emc.h>
+
void lpc32xx_uart_init(unsigned int uart_id);
void lpc32xx_mac_init(void);
void lpc32xx_mlc_nand_init(void);
void lpc32xx_i2c_init(unsigned int devnum);
void lpc32xx_ssp_init(void);
-
+#if defined(CONFIG_SPL_BUILD)
+void ddr_init(const struct emc_dram_settings *dram);
+#endif
#endif /* _LPC32XX_SYS_PROTO_H */