ARM: OMAP4+: Clean up the pmic code
The pmic code is duplicated for OMAP 4 and 5.
Instead move the data to Soc specific place and
share the code.
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
diff --git a/arch/arm/cpu/armv7/omap-common/clocks-common.c b/arch/arm/cpu/armv7/omap-common/clocks-common.c
index 2becc4a..88e5336 100644
--- a/arch/arm/cpu/armv7/omap-common/clocks-common.c
+++ b/arch/arm/cpu/armv7/omap-common/clocks-common.c
@@ -443,44 +443,45 @@
}
#endif
-void do_scale_tps62361(int gpio, u32 reg, u32 volt_mv)
+u32 get_offset_code(u32 volt_offset, struct pmic_data *pmic)
{
- u32 step;
- int ret = 0;
+ u32 offset_code;
- /* See if we can first get the GPIO if needed */
- if (gpio >= 0)
- ret = gpio_request(gpio, "TPS62361_VSEL0_GPIO");
- if (ret < 0) {
- printf("%s: gpio %d request failed %d\n", __func__, gpio, ret);
- gpio = -1;
- }
+ volt_offset -= pmic->base_offset;
- /* Pull the GPIO low to select SET0 register, while we program SET1 */
- if (gpio >= 0)
- gpio_direction_output(gpio, 0);
+ offset_code = (volt_offset + pmic->step - 1) / pmic->step;
- step = volt_mv - TPS62361_BASE_VOLT_MV;
- step /= 10;
-
- debug("do_scale_tps62361: volt - %d step - 0x%x\n", volt_mv, step);
- if (omap_vc_bypass_send_value(TPS62361_I2C_SLAVE_ADDR, reg, step))
- puts("Scaling voltage failed for vdd_mpu from TPS\n");
-
- /* Pull the GPIO high to select SET1 register */
- if (gpio >= 0)
- gpio_direction_output(gpio, 1);
+ /*
+ * Offset codes 1-6 all give the base voltage in Palmas
+ * Offset code 0 switches OFF the SMPS
+ */
+ return offset_code + pmic->start_code;
}
-void do_scale_vcore(u32 vcore_reg, u32 volt_mv)
+void do_scale_vcore(u32 vcore_reg, u32 volt_mv, struct pmic_data *pmic)
{
u32 offset_code;
u32 offset = volt_mv;
+ int ret = 0;
+
+ /* See if we can first get the GPIO if needed */
+ if (pmic->gpio_en)
+ ret = gpio_request(pmic->gpio, "PMIC_GPIO");
+
+ if (ret < 0) {
+ printf("%s: gpio %d request failed %d\n", __func__,
+ pmic->gpio, ret);
+ return;
+ }
+
+ /* Pull the GPIO low to select SET0 register, while we program SET1 */
+ if (pmic->gpio_en)
+ gpio_direction_output(pmic->gpio, 0);
/* convert to uV for better accuracy in the calculations */
offset *= 1000;
- offset_code = get_offset_code(offset);
+ offset_code = get_offset_code(offset, pmic);
debug("do_scale_vcore: volt - %d offset_code - 0x%x\n", volt_mv,
offset_code);
@@ -488,6 +489,36 @@
if (omap_vc_bypass_send_value(SMPS_I2C_SLAVE_ADDR,
vcore_reg, offset_code))
printf("Scaling voltage failed for 0x%x\n", vcore_reg);
+
+ if (pmic->gpio_en)
+ gpio_direction_output(pmic->gpio, 1);
+}
+
+/*
+ * Setup the voltages for vdd_mpu, vdd_core, and vdd_iva
+ * We set the maximum voltages allowed here because Smart-Reflex is not
+ * enabled in bootloader. Voltage initialization in the kernel will set
+ * these to the nominal values after enabling Smart-Reflex
+ */
+void scale_vcores(struct vcores_data const *vcores)
+{
+ omap_vc_init(PRM_VC_I2C_CHANNEL_FREQ_KHZ);
+
+ do_scale_vcore(vcores->core.addr, vcores->core.value,
+ vcores->core.pmic);
+
+ do_scale_vcore(vcores->mpu.addr, vcores->mpu.value,
+ vcores->mpu.pmic);
+
+ do_scale_vcore(vcores->mm.addr, vcores->mm.value,
+ vcores->mm.pmic);
+
+ if (emif_sdram_type() == EMIF_SDRAM_TYPE_DDR3) {
+ /* Configure LDO SRAM "magic" bits */
+ writel(2, (*prcm)->prm_sldo_core_setup);
+ writel(2, (*prcm)->prm_sldo_mpu_setup);
+ writel(2, (*prcm)->prm_sldo_mm_setup);
+ }
}
static inline void enable_clock_domain(u32 const clkctrl_reg, u32 enable_mode)
@@ -656,7 +687,7 @@
case OMAP_INIT_CONTEXT_UBOOT_FROM_NOR:
case OMAP_INIT_CONTEXT_UBOOT_AFTER_CH:
enable_basic_clocks();
- scale_vcores();
+ scale_vcores(*omap_vcores);
setup_dplls();
#ifdef CONFIG_SYS_CLOCKS_ENABLE_ALL
setup_non_essential_dplls();