dts: add device tree for STM32MP157C-ED1 board
Add minimal devicetree for STM32MP157C-ED1 board,
with only the devices to allow boot from SDCARD:
- RCC for clock and reset
- UART4 for console
- I2C and PMIC
- DDR
- SDMMC0 for SDCard
Waiting Kernel upstream for alignment.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 83e13ec..7dd1dff 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -500,6 +500,9 @@
dtb-$(CONFIG_ARCH_STI) += stih410-b2260.dtb
+dtb-$(CONFIG_TARGET_STM32MP1) += \
+ stm32mp157c-ed1.dtb
+
targets += $(dtb-y)
# Add any required device tree compiler flags here
diff --git a/arch/arm/dts/stm32mp15-ddr.dtsi b/arch/arm/dts/stm32mp15-ddr.dtsi
new file mode 100644
index 0000000..ddfa079
--- /dev/null
+++ b/arch/arm/dts/stm32mp15-ddr.dtsi
@@ -0,0 +1,155 @@
+/*
+ * Copyright : STMicroelectronics 2018
+ *
+ * SPDX-License-Identifier: GPL-2.0+ BSD-3-Clause
+ */
+
+/ {
+ soc {
+ ddr: ddr@0x5A003000{
+ u-boot,dm-pre-reloc;
+
+ compatible = "st,stm32mp1-ddr";
+
+ reg = <0x5A003000 0x550
+ 0x5A004000 0x234>;
+
+ clocks = <&rcc_clk AXIDCG>,
+ <&rcc_clk DDRC1>,
+ <&rcc_clk DDRC2>,
+ <&rcc_clk DDRPHYC>,
+ <&rcc_clk DDRCAPB>,
+ <&rcc_clk DDRPHYCAPB>;
+
+ clock-names = "axidcg",
+ "ddrc1",
+ "ddrc2",
+ "ddrphyc",
+ "ddrcapb",
+ "ddrphycapb";
+
+ st,mem-name = DDR_MEM_NAME;
+ st,mem-speed = <DDR_MEM_SPEED>;
+ st,mem-size = <DDR_MEM_SIZE>;
+
+ st,ctl-reg = <
+ DDR_MSTR
+ DDR_MRCTRL0
+ DDR_MRCTRL1
+ DDR_DERATEEN
+ DDR_DERATEINT
+ DDR_PWRCTL
+ DDR_PWRTMG
+ DDR_HWLPCTL
+ DDR_RFSHCTL0
+ DDR_RFSHCTL3
+ DDR_CRCPARCTL0
+ DDR_ZQCTL0
+ DDR_DFITMG0
+ DDR_DFITMG1
+ DDR_DFILPCFG0
+ DDR_DFIUPD0
+ DDR_DFIUPD1
+ DDR_DFIUPD2
+ DDR_DFIPHYMSTR
+ DDR_ODTMAP
+ DDR_DBG0
+ DDR_DBG1
+ DDR_DBGCMD
+ DDR_POISONCFG
+ DDR_PCCFG
+ >;
+
+ st,ctl-timing = <
+ DDR_RFSHTMG
+ DDR_DRAMTMG0
+ DDR_DRAMTMG1
+ DDR_DRAMTMG2
+ DDR_DRAMTMG3
+ DDR_DRAMTMG4
+ DDR_DRAMTMG5
+ DDR_DRAMTMG6
+ DDR_DRAMTMG7
+ DDR_DRAMTMG8
+ DDR_DRAMTMG14
+ DDR_ODTCFG
+ >;
+
+ st,ctl-map = <
+ DDR_ADDRMAP1
+ DDR_ADDRMAP2
+ DDR_ADDRMAP3
+ DDR_ADDRMAP4
+ DDR_ADDRMAP5
+ DDR_ADDRMAP6
+ DDR_ADDRMAP9
+ DDR_ADDRMAP10
+ DDR_ADDRMAP11
+ >;
+
+ st,ctl-perf = <
+ DDR_SCHED
+ DDR_SCHED1
+ DDR_PERFHPR1
+ DDR_PERFLPR1
+ DDR_PERFWR1
+ DDR_PCFGR_0
+ DDR_PCFGW_0
+ DDR_PCFGQOS0_0
+ DDR_PCFGQOS1_0
+ DDR_PCFGWQOS0_0
+ DDR_PCFGWQOS1_0
+ DDR_PCFGR_1
+ DDR_PCFGW_1
+ DDR_PCFGQOS0_1
+ DDR_PCFGQOS1_1
+ DDR_PCFGWQOS0_1
+ DDR_PCFGWQOS1_1
+ >;
+
+ st,phy-reg = <
+ DDR_PGCR
+ DDR_ACIOCR
+ DDR_DXCCR
+ DDR_DSGCR
+ DDR_DCR
+ DDR_ODTCR
+ DDR_ZQ0CR1
+ DDR_DX0GCR
+ DDR_DX1GCR
+ DDR_DX2GCR
+ DDR_DX3GCR
+ >;
+
+ st,phy-timing = <
+ DDR_PTR0
+ DDR_PTR1
+ DDR_PTR2
+ DDR_DTPR0
+ DDR_DTPR1
+ DDR_DTPR2
+ DDR_MR0
+ DDR_MR1
+ DDR_MR2
+ DDR_MR3
+ >;
+
+ st,phy-cal = <
+ DDR_DX0DLLCR
+ DDR_DX0DQTR
+ DDR_DX0DQSTR
+ DDR_DX1DLLCR
+ DDR_DX1DQTR
+ DDR_DX1DQSTR
+ DDR_DX2DLLCR
+ DDR_DX2DQTR
+ DDR_DX2DQSTR
+ DDR_DX3DLLCR
+ DDR_DX3DQTR
+ DDR_DX3DQSTR
+ >;
+
+ status = "okay";
+ };
+ };
+};
diff --git a/arch/arm/dts/stm32mp15-ddr3-2x4Gb-1066-binG.dtsi b/arch/arm/dts/stm32mp15-ddr3-2x4Gb-1066-binG.dtsi
new file mode 100644
index 0000000..352e470
--- /dev/null
+++ b/arch/arm/dts/stm32mp15-ddr3-2x4Gb-1066-binG.dtsi
@@ -0,0 +1,122 @@
+/*
+ * Copyright (C) 2018, STMicroelectronics - All Rights Reserved
+ *
+ * SPDX-License-Identifier: GPL-2.0+ BSD-3-Clause
+ */
+
+/* STM32MP157C ED1 and ED2 BOARD configuration
+ * 2x DDR3L 4Gb each, 16-bit, 533MHz, Single Die Package in flyby topology.
+ * Reference used NT5CC256M16DP-DI from NANYA
+ *
+ * DDR type / Platform DDR3/3L
+ * freq 533MHz
+ * width 32
+ * datasheet 0 = MT41J256M16-187 / DDR3-1066 bin G
+ * DDR density 8
+ * timing mode optimized
+ * Scheduling/QoS options : type = 2
+ * address mapping : RBC
+ */
+
+#define DDR_MEM_NAME "DDR3-1066 bin G 2x4Gb 533MHz v1.36"
+#define DDR_MEM_SPEED 533
+#define DDR_MEM_SIZE 0x40000000
+
+#define DDR_MSTR 0x00040401
+#define DDR_MRCTRL0 0x00000010
+#define DDR_MRCTRL1 0x00000000
+#define DDR_DERATEEN 0x00000000
+#define DDR_DERATEINT 0x00800000
+#define DDR_PWRCTL 0x00000000
+#define DDR_PWRTMG 0x00400010
+#define DDR_HWLPCTL 0x00000000
+#define DDR_RFSHCTL0 0x00210000
+#define DDR_RFSHCTL3 0x00000000
+#define DDR_RFSHTMG 0x0081008B
+#define DDR_CRCPARCTL0 0x00000000
+#define DDR_DRAMTMG0 0x121B2414
+#define DDR_DRAMTMG1 0x000A041C
+#define DDR_DRAMTMG2 0x0608090F
+#define DDR_DRAMTMG3 0x0050400C
+#define DDR_DRAMTMG4 0x08040608
+#define DDR_DRAMTMG5 0x06060403
+#define DDR_DRAMTMG6 0x02020002
+#define DDR_DRAMTMG7 0x00000202
+#define DDR_DRAMTMG8 0x00001005
+#define DDR_DRAMTMG14 0x000000A0
+#define DDR_ZQCTL0 0xC2000040
+#define DDR_DFITMG0 0x02060105
+#define DDR_DFITMG1 0x00000202
+#define DDR_DFILPCFG0 0x07000000
+#define DDR_DFIUPD0 0xC0400003
+#define DDR_DFIUPD1 0x00000000
+#define DDR_DFIUPD2 0x00000000
+#define DDR_DFIPHYMSTR 0x00000000
+#define DDR_ADDRMAP1 0x00080808
+#define DDR_ADDRMAP2 0x00000000
+#define DDR_ADDRMAP3 0x00000000
+#define DDR_ADDRMAP4 0x00001F1F
+#define DDR_ADDRMAP5 0x07070707
+#define DDR_ADDRMAP6 0x0F070707
+#define DDR_ADDRMAP9 0x00000000
+#define DDR_ADDRMAP10 0x00000000
+#define DDR_ADDRMAP11 0x00000000
+#define DDR_ODTCFG 0x06000600
+#define DDR_ODTMAP 0x00000001
+#define DDR_SCHED 0x00001201
+#define DDR_SCHED1 0x00000000
+#define DDR_PERFHPR1 0x01000001
+#define DDR_PERFLPR1 0x08000200
+#define DDR_PERFWR1 0x08000400
+#define DDR_DBG0 0x00000000
+#define DDR_DBG1 0x00000000
+#define DDR_DBGCMD 0x00000000
+#define DDR_POISONCFG 0x00000000
+#define DDR_PCCFG 0x00000010
+#define DDR_PCFGR_0 0x00010000
+#define DDR_PCFGW_0 0x00000000
+#define DDR_PCFGQOS0_0 0x02100B03
+#define DDR_PCFGQOS1_0 0x00800100
+#define DDR_PCFGWQOS0_0 0x01100B03
+#define DDR_PCFGWQOS1_0 0x01000200
+#define DDR_PCFGR_1 0x00010000
+#define DDR_PCFGW_1 0x00000000
+#define DDR_PCFGQOS0_1 0x02100B03
+#define DDR_PCFGQOS1_1 0x00800100
+#define DDR_PCFGWQOS0_1 0x01100B03
+#define DDR_PCFGWQOS1_1 0x01000200
+#define DDR_PGCR 0x01442E02
+#define DDR_PTR0 0x0022AA5B
+#define DDR_PTR1 0x04841104
+#define DDR_PTR2 0x042DA068
+#define DDR_ACIOCR 0x10400812
+#define DDR_DXCCR 0x00000C40
+#define DDR_DSGCR 0xF200001F
+#define DDR_DCR 0x0000000B
+#define DDR_DTPR0 0x38D488D0
+#define DDR_DTPR1 0x098B00D8
+#define DDR_DTPR2 0x10023600
+#define DDR_MR0 0x00000840
+#define DDR_MR1 0x00000000
+#define DDR_MR2 0x00000208
+#define DDR_MR3 0x00000000
+#define DDR_ODTCR 0x00010000
+#define DDR_ZQ0CR1 0x0000005B
+#define DDR_DX0GCR 0x0000CE81
+#define DDR_DX0DLLCR 0x40000000
+#define DDR_DX0DQTR 0xFFFFFFFF
+#define DDR_DX0DQSTR 0x3DB02000
+#define DDR_DX1GCR 0x0000CE81
+#define DDR_DX1DLLCR 0x40000000
+#define DDR_DX1DQTR 0xFFFFFFFF
+#define DDR_DX1DQSTR 0x3DB02000
+#define DDR_DX2GCR 0x0000CE81
+#define DDR_DX2DLLCR 0x40000000
+#define DDR_DX2DQTR 0xFFFFFFFF
+#define DDR_DX2DQSTR 0x3DB02000
+#define DDR_DX3GCR 0x0000CE81
+#define DDR_DX3DLLCR 0x40000000
+#define DDR_DX3DQTR 0xFFFFFFFF
+#define DDR_DX3DQSTR 0x3DB02000
+
+#include "stm32mp15-ddr.dtsi"
diff --git a/arch/arm/dts/stm32mp157-u-boot.dtsi b/arch/arm/dts/stm32mp157-u-boot.dtsi
new file mode 100644
index 0000000..d374b2b
--- /dev/null
+++ b/arch/arm/dts/stm32mp157-u-boot.dtsi
@@ -0,0 +1,134 @@
+/*
+ * Copyright : STMicroelectronics 2018
+ *
+ * SPDX-License-Identifier: GPL-2.0+ BSD-3-Clause
+ */
+
+/ {
+ aliases {
+ gpio0 = &gpioa;
+ gpio1 = &gpiob;
+ gpio2 = &gpioc;
+ gpio3 = &gpiod;
+ gpio4 = &gpioe;
+ gpio5 = &gpiof;
+ gpio6 = &gpiog;
+ gpio7 = &gpioh;
+ gpio8 = &gpioi;
+ gpio9 = &gpioj;
+ gpio10 = &gpiok;
+ gpio25 = &gpioz;
+ };
+
+ config {
+ u-boot,dm-pre-reloc;
+ };
+
+ clocks {
+ u-boot,dm-pre-reloc;
+ };
+
+ soc {
+ u-boot,dm-pre-reloc;
+ };
+};
+
+&clk_hsi {
+ u-boot,dm-pre-reloc;
+};
+
+&clk_hse {
+ u-boot,dm-pre-reloc;
+};
+
+&clk_lse {
+ u-boot,dm-pre-reloc;
+};
+
+&clk_lsi {
+ u-boot,dm-pre-reloc;
+};
+
+&clk_csi {
+ u-boot,dm-pre-reloc;
+};
+
+&rcc {
+ u-boot,dm-pre-reloc;
+};
+
+&rcc_clk {
+ u-boot,dm-pre-reloc;
+};
+
+&rcc_rst {
+ u-boot,dm-pre-reloc;
+};
+
+&pinctrl {
+ u-boot,dm-pre-reloc;
+};
+
+&pinctrl_z {
+ u-boot,dm-pre-reloc;
+};
+
+&gpioa {
+ compatible = "st,stm32-gpio";
+ u-boot,dm-pre-reloc;
+};
+
+&gpiob {
+ compatible = "st,stm32-gpio";
+ u-boot,dm-pre-reloc;
+};
+
+&gpioc {
+ compatible = "st,stm32-gpio";
+ u-boot,dm-pre-reloc;
+};
+
+&gpiod {
+ compatible = "st,stm32-gpio";
+ u-boot,dm-pre-reloc;
+};
+
+&gpioe {
+ compatible = "st,stm32-gpio";
+ u-boot,dm-pre-reloc;
+};
+
+&gpiof {
+ compatible = "st,stm32-gpio";
+ u-boot,dm-pre-reloc;
+};
+
+&gpiog {
+ compatible = "st,stm32-gpio";
+ u-boot,dm-pre-reloc;
+};
+
+&gpioh {
+ compatible = "st,stm32-gpio";
+ u-boot,dm-pre-reloc;
+};
+
+&gpioi {
+ compatible = "st,stm32-gpio";
+ u-boot,dm-pre-reloc;
+};
+
+&gpioj {
+ compatible = "st,stm32-gpio";
+ u-boot,dm-pre-reloc;
+};
+
+&gpiok {
+ compatible = "st,stm32-gpio";
+ u-boot,dm-pre-reloc;
+};
+
+&gpioz {
+ compatible = "st,stm32-gpio";
+ u-boot,dm-pre-reloc;
+};
diff --git a/arch/arm/dts/stm32mp157.dtsi b/arch/arm/dts/stm32mp157.dtsi
new file mode 100644
index 0000000..32d3984
--- /dev/null
+++ b/arch/arm/dts/stm32mp157.dtsi
@@ -0,0 +1,303 @@
+/* SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) */
+/*
+ * Copyright (C) STMicroelectronics 2018 - All Rights Reserved
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/stm32mp1-clks.h>
+#include <dt-bindings/reset-controller/stm32mp1-resets.h>
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu0: cpu@0 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <0>;
+ };
+
+ cpu1: cpu@1 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <1>;
+ };
+ };
+
+ aliases {
+ serial3 = &uart4;
+ };
+
+ intc: interrupt-controller@a0021000 {
+ compatible = "arm,cortex-a7-gic";
+ #interrupt-cells = <3>;
+ interrupt-controller;
+ reg = <0xa0021000 0x1000>,
+ <0xa0022000 0x2000>;
+ };
+
+ clocks {
+ clk_hse: clk-hse {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ };
+
+ clk_hsi: clk-hsi {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <64000000>;
+ };
+
+ clk_lse: clk-lse {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ };
+
+ clk_lsi: clk-lsi {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <32000>;
+ };
+
+ clk_csi: clk-csi {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <4000000>;
+ };
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ interrupt-parent = <&intc>;
+ ranges;
+
+ uart4: serial@40010000 {
+ compatible = "st,stm32h7-uart";
+ reg = <0x40010000 0x400>;
+ clocks = <&rcc_clk UART4_K>;
+ status = "disabled";
+ };
+
+ rcc: rcc@50000000 {
+ compatible = "syscon", "simple-mfd";
+
+ reg = <0x50000000 0x1000>;
+
+ rcc_clk: rcc-clk@50000000 {
+ #clock-cells = <1>;
+ compatible = "st,stm32mp1-rcc-clk";
+ };
+
+ rcc_rst: rcc-reset@50000000 {
+ #reset-cells = <1>;
+ compatible = "st,stm32mp1-rcc-rst";
+ };
+ };
+
+ pinctrl: pin-controller {
+ compatible = "st,stm32mp157-pinctrl";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x50002000 0xa400>;
+ pins-are-numbered;
+
+ gpioa: gpio@50002000 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0x0 0x400>;
+ clocks = <&rcc_clk GPIOA>;
+ st,bank-name = "GPIOA";
+ ngpios = <16>;
+ gpio-ranges = <&pinctrl 0 0 16>;
+ status = "disabled";
+ };
+
+ gpiob: gpio@50003000 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0x1000 0x400>;
+ clocks = <&rcc_clk GPIOB>;
+ st,bank-name = "GPIOB";
+ ngpios = <16>;
+ gpio-ranges = <&pinctrl 0 16 16>;
+ status = "disabled";
+ };
+
+ gpioc: gpio@50004000 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0x2000 0x400>;
+ clocks = <&rcc_clk GPIOC>;
+ st,bank-name = "GPIOC";
+ ngpios = <16>;
+ gpio-ranges = <&pinctrl 0 32 16>;
+ status = "disabled";
+ };
+
+ gpiod: gpio@50005000 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0x3000 0x400>;
+ clocks = <&rcc_clk GPIOD>;
+ st,bank-name = "GPIOD";
+ ngpios = <16>;
+ gpio-ranges = <&pinctrl 0 48 16>;
+ status = "disabled";
+ };
+
+ gpioe: gpio@50006000 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0x4000 0x400>;
+ clocks = <&rcc_clk GPIOE>;
+ st,bank-name = "GPIOE";
+ ngpios = <16>;
+ gpio-ranges = <&pinctrl 0 64 16>;
+ status = "disabled";
+ };
+
+ gpiof: gpio@50007000 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0x5000 0x400>;
+ clocks = <&rcc_clk GPIOF>;
+ st,bank-name = "GPIOF";
+ ngpios = <16>;
+ gpio-ranges = <&pinctrl 0 80 16>;
+ status = "disabled";
+ };
+
+ gpiog: gpio@50008000 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0x6000 0x400>;
+ clocks = <&rcc_clk GPIOG>;
+ st,bank-name = "GPIOG";
+ ngpios = <16>;
+ gpio-ranges = <&pinctrl 0 96 16>;
+ status = "disabled";
+ };
+
+ gpioh: gpio@50009000 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0x7000 0x400>;
+ clocks = <&rcc_clk GPIOH>;
+ st,bank-name = "GPIOH";
+ ngpios = <16>;
+ gpio-ranges = <&pinctrl 0 112 16>;
+ status = "disabled";
+ };
+
+ gpioi: gpio@5000a000 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0x8000 0x400>;
+ clocks = <&rcc_clk GPIOI>;
+ st,bank-name = "GPIOI";
+ ngpios = <16>;
+ gpio-ranges = <&pinctrl 0 128 16>;
+ status = "disabled";
+ };
+
+ gpioj: gpio@5000b000 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0x9000 0x400>;
+ clocks = <&rcc_clk GPIOJ>;
+ st,bank-name = "GPIOJ";
+ ngpios = <16>;
+ gpio-ranges = <&pinctrl 0 144 16>;
+ status = "disabled";
+ };
+
+ gpiok: gpio@5000c000 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0xa000 0x400>;
+ clocks = <&rcc_clk GPIOK>;
+ st,bank-name = "GPIOK";
+ ngpios = <8>;
+ gpio-ranges = <&pinctrl 0 160 8>;
+ status = "disabled";
+ };
+ };
+
+ pinctrl_z: pin-controller-z {
+ compatible = "st,stm32mp157-z-pinctrl";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 0x54004000 0x400>;
+ pins-are-numbered;
+
+ gpioz: gpio@54004000 {
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0 0x400>;
+ clocks = <&rcc_clk GPIOZ>;
+ st,bank-name = "GPIOZ";
+ st,bank-ioport = <11>;
+ ngpios = <8>;
+ gpio-ranges = <&pinctrl_z 0 400 8>;
+ status = "disabled";
+ };
+ };
+
+ sdmmc1: sdmmc@58005000 {
+ compatible = "st,stm32-sdmmc2";
+ reg = <0x58005000 0x1000>, <0x58006000 0x1000>;
+ reg-names = "sdmmc", "delay";
+ clocks = <&rcc_clk SDMMC1_K>;
+ resets = <&rcc_rst SDMMC1_R>;
+ st,idma = <1>;
+ cap-sd-highspeed;
+ cap-mmc-highspeed;
+ max-frequency = <120000000>;
+ status = "disabled";
+ };
+
+ i2c4: i2c@5c002000 {
+ compatible = "st,stm32f7-i2c";
+ reg = <0x5c002000 0x400>;
+ interrupt-names = "event", "error", "wakeup";
+ clocks = <&rcc_clk I2C4_K>;
+ resets = <&rcc_rst I2C4_R>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ wakeup-source;
+ status = "disabled";
+ };
+ };
+};
diff --git a/arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi b/arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi
new file mode 100644
index 0000000..94d27fb
--- /dev/null
+++ b/arch/arm/dts/stm32mp157c-ed1-u-boot.dtsi
@@ -0,0 +1,133 @@
+/*
+ * Copyright : STMicroelectronics 2018
+ *
+ * SPDX-License-Identifier: GPL-2.0+ BSD-3-Clause
+ */
+
+#include <dt-bindings/clock/stm32mp1-clksrc.h>
+#include "stm32mp157-u-boot.dtsi"
+#include "stm32mp15-ddr3-2x4Gb-1066-binG.dtsi"
+
+/ {
+ aliases {
+ mmc0 = &sdmmc1;
+ i2c3 = &i2c4;
+ };
+};
+
+&uart4_pins_a {
+ u-boot,dm-pre-reloc;
+ pins1 {
+ u-boot,dm-pre-reloc;
+ };
+ pins2 {
+ u-boot,dm-pre-reloc;
+ };
+};
+
+&i2c4_pins_a {
+ u-boot,dm-pre-reloc;
+ pins {
+ u-boot,dm-pre-reloc;
+ };
+};
+
+&uart4 {
+ u-boot,dm-pre-reloc;
+};
+
+&i2c4 {
+ u-boot,dm-pre-reloc;
+};
+
+&pmic {
+ u-boot,dm-pre-reloc;
+};
+
+/* CLOCK init */
+&rcc_clk {
+ st,clksrc = <
+ CLK_MPU_PLL1P
+ CLK_AXI_PLL2P
+ CLK_MCU_PLL3P
+ CLK_PLL12_HSE
+ CLK_PLL3_HSE
+ CLK_PLL4_HSE
+ CLK_RTC_LSE
+ CLK_MCO1_DISABLED
+ CLK_MCO2_DISABLED
+ >;
+
+ st,clkdiv = <
+ 1 /*MPU*/
+ 0 /*AXI*/
+ 0 /*MCU*/
+ 1 /*APB1*/
+ 1 /*APB2*/
+ 1 /*APB3*/
+ 1 /*APB4*/
+ 2 /*APB5*/
+ 23 /*RTC*/
+ 0 /*MCO1*/
+ 0 /*MCO2*/
+ >;
+
+ st,pkcs = <
+ CLK_CKPER_DISABLED
+ CLK_SDMMC12_PLL3R
+ CLK_I2C46_PCLK5
+ CLK_I2C12_PCLK1
+ CLK_I2C35_PCLK1
+ CLK_UART1_PCLK5
+ CLK_UART24_PCLK1
+ CLK_UART35_PCLK1
+ CLK_UART6_PCLK2
+ CLK_UART78_PCLK1
+ >;
+
+ /* VCO = 1300.0 MHz => P = 650 (CPU) */
+ pll1: st,pll@0 {
+ cfg = < 2 80 0 0 0 PQR(1,0,0) >;
+ frac = < 0x800 >;
+ u-boot,dm-pre-reloc;
+ };
+
+ /* VCO = 1066.0 MHz => P = 266 (AXI), Q = 533 (GPU), R = 533 (DDR) */
+ pll2: st,pll@1 {
+ cfg = < 2 65 1 0 0 PQR(1,1,1) >;
+ frac = < 0x1400 >;
+ u-boot,dm-pre-reloc;
+ };
+
+ /* VCO = 774.0 MHz => P = 194, Q = 37, R = 97 */
+ pll3: st,pll@2 {
+ cfg = < 3 128 3 20 7 PQR(1,1,1) >;
+ u-boot,dm-pre-reloc;
+ };
+
+ /* VCO = 508.0 MHz => P = 56, Q = 56, R = 56 */
+ pll4: st,pll@3 {
+ cfg = < 5 126 8 8 8 PQR(1,1,1) >;
+ u-boot,dm-pre-reloc;
+ };
+};
+
+/* SPL part **************************************/
+/* MMC1 boot */
+&sdmmc1_b4_pins_a {
+ u-boot,dm-spl;
+ pins {
+ u-boot,dm-spl;
+ };
+};
+
+&sdmmc1_dir_pins_a {
+ u-boot,dm-spl;
+ pins {
+ u-boot,dm-spl;
+ };
+};
+
+&sdmmc1 {
+ u-boot,dm-spl;
+};
diff --git a/arch/arm/dts/stm32mp157c-ed1.dts b/arch/arm/dts/stm32mp157c-ed1.dts
new file mode 100644
index 0000000..4b20fab
--- /dev/null
+++ b/arch/arm/dts/stm32mp157c-ed1.dts
@@ -0,0 +1,167 @@
+/* SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) */
+/*
+ * Copyright (C) STMicroelectronics 2017 - All Rights Reserved
+ * Author: Ludovic Barre <ludovic.barre@st.com> for STMicroelectronics.
+ */
+
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/stm32-pinfunc.h>
+
+/ {
+ model = "STMicroelectronics STM32MP157C pmic eval daughter";
+ compatible = "st,stm32mp157c-ed1", "st,stm32mp157";
+
+ chosen {
+ bootargs = "earlyprintk console=ttyS3,115200 root=/dev/ram";
+ stdout-path = "serial3:115200n8";
+ };
+
+ memory {
+ reg = <0xC0000000 0x40000000>;
+ };
+};
+
+&gpioa {
+ status = "okay";
+};
+
+&gpiob {
+ status = "okay";
+};
+
+&gpioc {
+ status = "okay";
+};
+
+&gpiod {
+ status = "okay";
+};
+
+&gpioe {
+ status = "okay";
+};
+
+&gpiof {
+ status = "okay";
+};
+
+&gpiog {
+ status = "okay";
+};
+
+&gpioh {
+ status = "okay";
+};
+
+&gpioi {
+ status = "okay";
+};
+
+&gpioj {
+ status = "okay";
+};
+
+&gpiok {
+ status = "okay";
+};
+
+&gpioz {
+ status = "okay";
+};
+
+&pinctrl {
+ uart4_pins_a: uart4@0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('G', 11, AF6)>; /* UART4_TX */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <0>;
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('B', 2, AF8)>; /* UART4_RX */
+ bias-disable;
+ };
+ };
+
+ sdmmc1_b4_pins_a: sdmmc1-b4@0 {
+ pins {
+ pinmux = <STM32_PINMUX('C', 8, AF12)>, /* SDMMC1_D0 */
+ <STM32_PINMUX('C', 9, AF12)>, /* SDMMC1_D1 */
+ <STM32_PINMUX('C', 10, AF12)>, /* SDMMC1_D2 */
+ <STM32_PINMUX('C', 11, AF12)>, /* SDMMC1_D3 */
+ <STM32_PINMUX('C', 12, AF12)>, /* SDMMC1_CK */
+ <STM32_PINMUX('D', 2, AF12)>; /* SDMMC1_CMD */
+ slew-rate = <3>;
+ drive-push-pull;
+ bias-disable;
+ };
+ };
+
+ sdmmc1_dir_pins_a: sdmmc1-dir@0 {
+ pins {
+ pinmux = <STM32_PINMUX('F', 2, AF11)>, /* SDMMC1_D0DIR */
+ <STM32_PINMUX('C', 7, AF8)>, /* SDMMC1_D123DIR */
+ <STM32_PINMUX('B', 9, AF11)>, /* SDMMC1_CDIR */
+ <STM32_PINMUX('E', 4, AF8)>; /* SDMMC1_CKIN */
+ slew-rate = <3>;
+ drive-push-pull;
+ bias-pull-up;
+ };
+ };
+};
+
+&pinctrl_z {
+ i2c4_pins_a: i2c4@0 {
+ pins {
+ pinmux = <STM32_PINMUX('Z', 4, AF6)>, /* I2C4_SCL */
+ <STM32_PINMUX('Z', 5, AF6)>; /* I2C4_SDA */
+ bias-disable;
+ drive-open-drain;
+ slew-rate = <0>;
+ };
+ };
+};
+
+&i2c4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c4_pins_a>;
+ i2c-scl-rising-time-ns = <185>;
+ i2c-scl-falling-time-ns = <20>;
+ status = "okay";
+
+ pmic: stpmu1@33 {
+ compatible = "st,stpmu1";
+ reg = <0x33>;
+ interrupts = <0 2>;
+ interrupt-parent = <&gpioa>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ status = "okay";
+ };
+};
+
+&sdmmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_dir_pins_a>;
+ broken-cd;
+ st,dirpol;
+ st,negedge;
+ st,pin-ckin;
+ bus-width = <4>;
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ sd-uhs-sdr50;
+ sd-uhs-ddr50;
+ sd-uhs-sdr104;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4_pins_a>;
+ status = "okay";
+};