/*
 * Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
 * on behalf of DENX Software Engineering GmbH
 *
 * SPDX-License-Identifier:	GPL-2.0+ 
 */
#ifndef __M28EVK_CONFIG_H__
#define __M28EVK_CONFIG_H__

/*
 * SoC configurations
 */
#define CONFIG_MX28				/* i.MX28 SoC */
#define CONFIG_MXS_GPIO				/* GPIO control */
#define CONFIG_SYS_HZ		1000		/* Ticks per second */

/*
 * Define M28EVK machine type by hand until it lands in mach-types
 */
#define MACH_TYPE_M28EVK	3613

#define CONFIG_MACH_TYPE	MACH_TYPE_M28EVK

#include <asm/arch/regs-base.h>

#define CONFIG_SYS_NO_FLASH
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_ARCH_MISC_INIT

/*
 * SPL
 */
#define CONFIG_SPL
#define CONFIG_SPL_NO_CPU_SUPPORT_CODE
#define CONFIG_SPL_START_S_PATH		"arch/arm/cpu/arm926ejs/mxs"
#define CONFIG_SPL_LDSCRIPT	"arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds"
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_GPIO_SUPPORT

/*
 * U-Boot Commands
 */
#include <config_cmd_default.h>
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DOS_PARTITION

#define CONFIG_CMD_CACHE
#define CONFIG_CMD_DATE
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_FAT
#define CONFIG_CMD_GPIO
#define CONFIG_CMD_GREPENV
#define CONFIG_CMD_I2C
#define CONFIG_CMD_MII
#define CONFIG_CMD_MMC
#define CONFIG_CMD_NAND
#define CONFIG_CMD_NAND_TRIMFFS
#define CONFIG_CMD_NET
#define CONFIG_CMD_NFS
#define CONFIG_CMD_PING
#define CONFIG_CMD_SETEXPR
#define CONFIG_CMD_SF
#define CONFIG_CMD_SPI
#define CONFIG_CMD_USB
#define	CONFIG_VIDEO

#define CONFIG_REGEX			/* Enable regular expression support */

/*
 * Memory configurations
 */
#define CONFIG_NR_DRAM_BANKS		1		/* 1 bank of DRAM */
#define PHYS_SDRAM_1			0x40000000	/* Base address */
#define PHYS_SDRAM_1_SIZE		0x20000000	/* Max 512 MB RAM */
#define CONFIG_SYS_MALLOC_LEN		0x00400000	/* 4 MB for malloc */
#define CONFIG_SYS_GBL_DATA_SIZE	128		/* Initial data */
#define CONFIG_SYS_MEMTEST_START	0x40000000	/* Memtest start adr */
#define CONFIG_SYS_MEMTEST_END		0x40400000	/* 4 MB RAM test */
#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM_1
/* Point initial SP in SRAM so SPL can use it too. */

#define CONFIG_SYS_INIT_RAM_ADDR	0x00000000
#define CONFIG_SYS_INIT_RAM_SIZE	(128 * 1024)

#define CONFIG_SYS_INIT_SP_OFFSET \
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
/*
 * We need to sacrifice first 4 bytes of RAM here to avoid triggering some
 * strange BUG in ROM corrupting first 4 bytes of RAM when loading U-Boot
 * binary. In case there was more of this mess, 0x100 bytes are skipped.
 */
#define CONFIG_SYS_TEXT_BASE		0x40000100

/*
 * U-Boot general configurations
 */
#define CONFIG_SYS_LONGHELP
#define CONFIG_SYS_PROMPT	"=> "
#define CONFIG_SYS_CBSIZE	1024		/* Console I/O buffer size */
#define CONFIG_SYS_PBSIZE	\
	(CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
						/* Print buffer size */
#define CONFIG_SYS_MAXARGS	32		/* Max number of command args */
#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE
						/* Boot argument buffer size */
#define CONFIG_VERSION_VARIABLE			/* U-BOOT version */
#define CONFIG_AUTO_COMPLETE			/* Command auto complete */
#define CONFIG_CMDLINE_EDITING			/* Command history etc */
#define CONFIG_SYS_HUSH_PARSER

/*
 * Serial Driver
 */
#define CONFIG_PL011_SERIAL
#define CONFIG_PL011_CLOCK		24000000
#define CONFIG_PL01x_PORTS		{ (void *)MXS_UARTDBG_BASE }
#define CONFIG_CONS_INDEX		0
#define CONFIG_BAUDRATE			115200	/* Default baud rate */

/*
 * MMC Driver
 */
#ifdef	CONFIG_CMD_MMC
#define CONFIG_MMC
#define CONFIG_BOUNCE_BUFFER
#define CONFIG_GENERIC_MMC
#define CONFIG_MXS_MMC
#endif

/*
 * APBH DMA
 */
#define CONFIG_APBH_DMA

/*
 * NAND
 */
#define CONFIG_ENV_SIZE			(16 * 1024)
#ifdef	CONFIG_CMD_NAND
#define CONFIG_NAND_MXS
#define CONFIG_SYS_MAX_NAND_DEVICE	1
#define CONFIG_SYS_NAND_BASE		0x60000000
#define CONFIG_SYS_NAND_5_ADDR_CYCLE

/* Environment is in NAND */
#define CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_SIZE_REDUND		CONFIG_ENV_SIZE
#define CONFIG_ENV_SECT_SIZE		(128 * 1024)
#define CONFIG_ENV_RANGE		(512 * 1024)
#define CONFIG_ENV_OFFSET		0x300000
#define CONFIG_ENV_OFFSET_REDUND	\
		(CONFIG_ENV_OFFSET + CONFIG_ENV_RANGE)

#define CONFIG_CMD_UBI
#define CONFIG_CMD_UBIFS
#define CONFIG_CMD_MTDPARTS
#define CONFIG_RBTREE
#define CONFIG_LZO
#define CONFIG_MTD_DEVICE
#define CONFIG_MTD_PARTITIONS
#define MTDIDS_DEFAULT			"nand0=gpmi-nand"
#define MTDPARTS_DEFAULT			\
	"mtdparts=gpmi-nand:"			\
		"3m(bootloader)ro,"		\
		"512k(environment),"		\
		"512k(redundant-environment),"	\
		"4m(kernel),"			\
		"128k(fdt),"			\
		"8m(ramdisk),"			\
		"-(filesystem)"
#else
#define CONFIG_ENV_IS_NOWHERE
#endif

/*
 * Ethernet on SOC (FEC)
 */
#ifdef	CONFIG_CMD_NET
#define CONFIG_ETHPRIME			"FEC0"
#define CONFIG_FEC_MXC
#define CONFIG_MII
#define CONFIG_FEC_XCV_TYPE		RMII
#endif

/*
 * I2C
 */
#ifdef	CONFIG_CMD_I2C
#define CONFIG_I2C_MXS
#define CONFIG_HARD_I2C
#define CONFIG_SYS_I2C_SPEED		400000
#endif

/*
 * EEPROM
 */
#ifdef	CONFIG_CMD_EEPROM
#define CONFIG_SYS_I2C_MULTI_EEPROMS
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	2
#endif

/*
 * RTC
 */
#ifdef	CONFIG_CMD_DATE
/* Use the internal RTC in the MXS chip */
#define CONFIG_RTC_INTERNAL
#ifdef	CONFIG_RTC_INTERNAL
#define CONFIG_RTC_MXS
#else
#define CONFIG_RTC_M41T62
#define CONFIG_SYS_I2C_RTC_ADDR		0x68
#define CONFIG_SYS_M41T11_BASE_YEAR	2000
#endif
#endif

/*
 * USB
 */
#ifdef	CONFIG_CMD_USB
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_MXS
#define CONFIG_EHCI_MXS_PORT0
#define CONFIG_EHCI_MXS_PORT1
#define CONFIG_USB_MAX_CONTROLLER_COUNT	2
#define CONFIG_EHCI_IS_TDI
#define CONFIG_USB_STORAGE
#endif

/*
 * SPI
 */
#ifdef	CONFIG_CMD_SPI
#define CONFIG_HARD_SPI
#define CONFIG_MXS_SPI
#define CONFIG_SPI_HALF_DUPLEX
#define CONFIG_DEFAULT_SPI_BUS		2
#define CONFIG_DEFAULT_SPI_CS		0
#define CONFIG_DEFAULT_SPI_MODE		SPI_MODE_0

/* SPI FLASH */
#ifdef	CONFIG_CMD_SF
#define CONFIG_SPI_FLASH
#define CONFIG_SPI_FLASH_STMICRO
#define CONFIG_SF_DEFAULT_BUS		2
#define CONFIG_SF_DEFAULT_CS		0
#define CONFIG_SF_DEFAULT_SPEED		40000000
#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0

#define CONFIG_ENV_SPI_BUS		2
#define CONFIG_ENV_SPI_CS		0
#define CONFIG_ENV_SPI_MAX_HZ		40000000
#define CONFIG_ENV_SPI_MODE		SPI_MODE_0
#endif
#endif

/*
 * LCD
 */
#ifdef	CONFIG_VIDEO
#define	CONFIG_CFB_CONSOLE
#define	CONFIG_VIDEO_MXS
#define	CONFIG_VIDEO_LOGO
#define	CONFIG_VIDEO_SW_CURSOR
#define	CONFIG_VGA_AS_SINGLE_DEVICE
#define	CONFIG_SYS_CONSOLE_IS_IN_ENV
#define	CONFIG_SPLASH_SCREEN
#define	CONFIG_CMD_BMP
#define	CONFIG_BMP_16BPP
#define	CONFIG_VIDEO_BMP_RLE8
#define	CONFIG_VIDEO_BMP_GZIP
#define	CONFIG_SYS_VIDEO_LOGO_MAX_SIZE	(512 << 10)
#endif

/*
 * Boot Linux
 */
#define CONFIG_CMDLINE_TAG
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_BOOTDELAY	3
#define CONFIG_BOOTFILE		"uImage"
#define CONFIG_BOOTARGS		"console=ttyAMA0,115200n8 "
#define CONFIG_BOOTCOMMAND	"run bootcmd_net"
#define CONFIG_LOADADDR		0x42000000
#define CONFIG_SYS_LOAD_ADDR	CONFIG_LOADADDR
#define CONFIG_OF_LIBFDT

/*
 * Extra Environments
 */
#define CONFIG_EXTRA_ENV_SETTINGS					\
	"update_nand_full_filename=u-boot.nand\0"			\
	"update_nand_firmware_filename=u-boot.sb\0"			\
	"update_sd_firmware_filename=u-boot.sd\0"			\
	"update_nand_firmware_maxsz=0x100000\0"				\
	"update_nand_stride=0x40\0"	/* MX28 datasheet ch. 12.12 */	\
	"update_nand_count=0x4\0"	/* MX28 datasheet ch. 12.12 */	\
	"update_nand_get_fcb_size="	/* Get size of FCB blocks */	\
		"nand device 0 ; "					\
		"nand info ; "						\
		"setexpr fcb_sz ${update_nand_stride} * ${update_nand_count};" \
		"setexpr update_nand_fcb ${fcb_sz} * ${nand_writesize}\0" \
	"update_nand_full="		/* Update FCB, DBBT and FW */	\
		"if tftp ${update_nand_full_filename} ; then "		\
		"run update_nand_get_fcb_size ; "			\
		"nand scrub -y 0x0 ${filesize} ; "			\
		"nand write.raw ${loadaddr} 0x0 ${fcb_sz} ; "	\
		"setexpr update_off ${loadaddr} + ${update_nand_fcb} ; " \
		"setexpr update_sz ${filesize} - ${update_nand_fcb} ; " \
		"nand write ${update_off} ${update_nand_fcb} ${update_sz} ; " \
		"fi\0"							\
	"update_nand_firmware="		/* Update only firmware */	\
		"if tftp ${update_nand_firmware_filename} ; then "	\
		"run update_nand_get_fcb_size ; "			\
		"setexpr fcb_sz ${update_nand_fcb} * 2 ; " /* FCB + DBBT */ \
		"setexpr fw_sz ${update_nand_firmware_maxsz} * 2 ; "	\
		"setexpr fw_off ${fcb_sz} + ${update_nand_firmware_maxsz};" \
		"nand erase ${fcb_sz} ${fw_sz} ; "			\
		"nand write ${loadaddr} ${fcb_sz} ${filesize} ; "	\
		"nand write ${loadaddr} ${fw_off} ${filesize} ; "	\
		"fi\0"							\
	"update_sd_firmware="		/* Update the SD firmware partition */ \
		"if mmc rescan ; then "					\
		"if tftp ${update_sd_firmware_filename} ; then "	\
		"setexpr fw_sz ${filesize} / 0x200 ; "	/* SD block size */ \
		"setexpr fw_sz ${fw_sz} + 1 ; "				\
		"mmc write ${loadaddr} 0x800 ${fw_sz} ; "		\
		"fi ; "							\
		"fi\0"

#endif /* __M28EVK_CONFIG_H__ */