PowerPC: keymile: Add support for kmcent2 board
Add basic support for the Hitachi Power Grids kmcent2 board, based
on the NXP QorIQ T1040 SoC.
Signed-off-by: Valentin Longchamp <valentin.longchamp@hitachi-powergrids.com>
Signed-off-by: Rainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: Niel Fourie <lusus@denx.de>
Cc: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
[Fixed blank line at EOF errors]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
diff --git a/board/keymile/Kconfig b/board/keymile/Kconfig
index e590690..6b7377c 100644
--- a/board/keymile/Kconfig
+++ b/board/keymile/Kconfig
@@ -114,6 +114,7 @@
Page size of inventory in EEPROM.
source "board/keymile/km83xx/Kconfig"
+source "board/keymile/kmcent2/Kconfig"
source "board/keymile/kmp204x/Kconfig"
source "board/keymile/km_arm/Kconfig"
diff --git a/board/keymile/common/ivm.c b/board/keymile/common/ivm.c
index e989bf6..bc8ffd5 100644
--- a/board/keymile/common/ivm.c
+++ b/board/keymile/common/ivm.c
@@ -321,6 +321,11 @@
process_mac(valbuf, page2, mac_address_offset, true);
env_set((char *)"eth1addr", (char *)valbuf);
}
+ if (IS_ENABLED(CONFIG_TARGET_KMCENT2)) {
+ /* 3rd ethernet interface */
+ process_mac(valbuf, page2, 2, true);
+ env_set((char *)"eth4addr", (char *)valbuf);
+ }
return 0;
}
diff --git a/board/keymile/kmcent2/Kconfig b/board/keymile/kmcent2/Kconfig
new file mode 100644
index 0000000..848d230
--- /dev/null
+++ b/board/keymile/kmcent2/Kconfig
@@ -0,0 +1,17 @@
+if TARGET_KMCENT2
+
+config SYS_BOARD
+ default "kmcent2"
+
+config SYS_VENDOR
+ default "keymile"
+
+config SYS_CONFIG_NAME
+ default "kmcent2"
+
+config BOARD_SPECIFIC_OPTIONS
+ def_bool y
+ select ARCH_T1040
+ select PHYS_64BIT
+
+endif
diff --git a/board/keymile/kmcent2/MAINTAINERS b/board/keymile/kmcent2/MAINTAINERS
new file mode 100644
index 0000000..1426475
--- /dev/null
+++ b/board/keymile/kmcent2/MAINTAINERS
@@ -0,0 +1,8 @@
+KMCENT2 BOARD
+M: Niel Fourie <lusus@denx.de>
+S: Maintained
+F: board/keymile/kmcent2/
+F: include/configs/kmcent2.h
+F: configs/kmcent2_defconfig
+F: arch/powerpc/dts/kmcent2.dts
+F: arch/powerpc/dts/kmcent2-u-boot.dtsi
diff --git a/board/keymile/kmcent2/Makefile b/board/keymile/kmcent2/Makefile
new file mode 100644
index 0000000..6b26e86
--- /dev/null
+++ b/board/keymile/kmcent2/Makefile
@@ -0,0 +1,14 @@
+# SPDX-License-Identifier: GPL-2.0+
+# (C) Copyright 2016 Keymile AG
+# Rainer Boschung <rainer.boschung@keymile.com>
+#
+# Copyright 2013 Freescale Semiconductor, Inc.
+#
+
+obj-y += kmcent2.o
+obj-y += ddr.o
+obj-y += law.o
+obj-y += tlb.o
+obj-y += ../common/common.o
+obj-y += ../common/ivm.o
+obj-y += ../common/qrio.o
diff --git a/board/keymile/kmcent2/ddr.c b/board/keymile/kmcent2/ddr.c
new file mode 100644
index 0000000..4f77820
--- /dev/null
+++ b/board/keymile/kmcent2/ddr.c
@@ -0,0 +1,88 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * (C) Copyright 2016 Keymile AG
+ * Rainer Boschung <rainer.boschung@keymile.com>
+ *
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ */
+
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+#include <asm/mpc85xx_gpio.h>
+#include <fsl_ddr_sdram.h>
+#include <fsl_ddr_dimm_params.h>
+#include <hwconfig.h>
+#include <i2c.h>
+#include <init.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define DQSn_POS(n) (3 - (((n) - 1) % 4)) * 8
+#define DQSn_START(n, start) ((start) << DQSn_POS(n))
+
+void fsl_ddr_board_options(memctl_options_t *popts, dimm_params_t *pdimm,
+ unsigned int ctrl_num)
+{
+ if (ctrl_num > 1) {
+ printf("Not supported controller number %d\n", ctrl_num);
+ return;
+ }
+
+ /* 1/2 clk delay between wr command and data strobe */
+ popts->write_data_delay = 4;
+ /* clk lauched 1/2 applied cylcle after address command */
+ popts->clk_adjust = 4;
+ /* 1T timing: command/address held for only 1 cycle */
+ popts->twot_en = 0;
+ popts->threet_en = 0;
+
+ /* optimize cpo for erratum A-009942 */
+ popts->cpo_sample = 0x3b;
+
+ /* we have only one module, half str should be OK */
+ popts->half_strength_driver_enable = 1;
+ /*
+ * Write leveling override
+ */
+ /* set for DDR3-1600 */
+ popts->wrlvl_override = 1;
+ popts->wrlvl_sample = 0xf;
+ popts->wrlvl_start = 0x7;
+ /* DQS write leveling start time according layout */
+ popts->wrlvl_ctl_2 = (DQSn_START(1, 0x06) |
+ DQSn_START(2, 0x06) |
+ DQSn_START(3, 0x07) |
+ DQSn_START(4, 0x07));
+ popts->wrlvl_ctl_3 = (DQSn_START(5, 0x07) |
+ DQSn_START(6, 0x08) |
+ DQSn_START(7, 0x08) |
+ DQSn_START(8, 0x08));
+
+ /*
+ * rtt and wtt_wr override
+ */
+ popts->rtt_override = 0;
+
+ /* Enable ZQ calibration */
+ popts->zq_en = 1;
+
+ /* DHC_EN =1, ODT = 75 Ohm */
+ popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
+ popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
+}
+
+int dram_init(void)
+{
+ phys_size_t dram_size;
+
+ puts("Initializing....using SPD\n");
+
+ dram_size = fsl_ddr_sdram();
+
+ dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+ dram_size *= 0x100000;
+
+ gd->ram_size = dram_size;
+
+ return 0;
+}
diff --git a/board/keymile/kmcent2/kmcent2.c b/board/keymile/kmcent2/kmcent2.c
new file mode 100644
index 0000000..4f5164e
--- /dev/null
+++ b/board/keymile/kmcent2/kmcent2.c
@@ -0,0 +1,353 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * (C) Copyright 2016 Keymile AG
+ * Rainer Boschung <rainer.boschung@keymile.com>
+ *
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ */
+
+#include <asm/cache.h>
+#include <asm/fsl_fdt.h>
+#include <asm/fsl_law.h>
+#include <asm/fsl_liodn.h>
+#include <asm/fsl_portals.h>
+#include <asm/fsl_serdes.h>
+#include <asm/immap_85xx.h>
+#include <asm/mmu.h>
+#include <asm/processor.h>
+#include <fdt_support.h>
+#include <fm_eth.h>
+#include <hwconfig.h>
+#include <image.h>
+#include <linux/compiler.h>
+#include <net.h>
+#include <netdev.h>
+#include <vsc9953.h>
+
+#include "../common/common.h"
+#include "../common/qrio.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+static uchar ivm_content[CONFIG_SYS_IVM_EEPROM_MAX_LEN];
+
+int checkboard(void)
+{
+ printf("Board: Hitachi Power Grids %s\n", KM_BOARD_NAME);
+
+ return 0;
+}
+
+#define RSTRQSR1_WDT_RR 0x00200000
+#define RSTRQSR1_SW_RR 0x00100000
+
+int board_early_init_f(void)
+{
+ struct fsl_ifc ifc = {(void *)CONFIG_SYS_IFC_ADDR, (void *)NULL};
+ ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ bool cpuwd_flag = false;
+
+ /* board specific IFC configuration: increased bus turnaround time */
+ setbits_be32(&ifc.gregs->ifc_gcr, 8 << IFC_GCR_TBCTL_TRN_TIME_SHIFT);
+
+ /* configure mode for uP reset request */
+ qrio_uprstreq(UPREQ_CORE_RST);
+
+ /* board only uses the DDR_MCK0, so disable the DDR_MCK1 */
+ setbits_be32(&gur->ddrclkdr, 0x40000000);
+
+ /* set reset reason according CPU register */
+ if ((gur->rstrqsr1 & (RSTRQSR1_WDT_RR | RSTRQSR1_SW_RR)) ==
+ RSTRQSR1_WDT_RR)
+ cpuwd_flag = true;
+
+ qrio_cpuwd_flag(cpuwd_flag);
+ /* clear CPU bits by writing 1 */
+ setbits_be32(&gur->rstrqsr1, RSTRQSR1_WDT_RR | RSTRQSR1_SW_RR);
+
+ /* configure PRST lines for the application: */
+ /*
+ * ETHSW_DDR_RST:
+ * reset at power-up and unit reset only and enable WD on it
+ */
+ qrio_prstcfg(KM_ETHSW_DDR_RST, PRSTCFG_POWUP_UNIT_RST);
+ qrio_wdmask(KM_ETHSW_DDR_RST, true);
+ /*
+ * XES_PHY_RST:
+ * reset at power-up and unit reset only and enable WD on it
+ */
+ qrio_prstcfg(KM_XES_PHY_RST, PRSTCFG_POWUP_UNIT_RST);
+ qrio_wdmask(KM_XES_PHY_RST, true);
+ /*
+ * ES_PHY_RST:
+ * reset at power-up and unit reset only and enable WD on it
+ */
+ qrio_prstcfg(KM_ES_PHY_RST, PRSTCFG_POWUP_UNIT_RST);
+ qrio_wdmask(KM_ES_PHY_RST, true);
+ /*
+ * EFE_RST:
+ * reset at power-up and unit reset only and enable WD on it
+ */
+ qrio_prstcfg(KM_EFE_RST, PRSTCFG_POWUP_UNIT_RST);
+ qrio_wdmask(KM_EFE_RST, true);
+ /*
+ * BFTIC4_RST:
+ * reset at power-up and unit reset only and enable WD on it
+ */
+ qrio_prstcfg(KM_BFTIC4_RST, PRSTCFG_POWUP_UNIT_RST);
+ qrio_wdmask(KM_BFTIC4_RST, true);
+ /*
+ * DPAXE_RST:
+ * reset at power-up and unit reset only and enable WD on it
+ */
+ qrio_prstcfg(KM_DPAXE_RST, PRSTCFG_POWUP_UNIT_RST);
+ qrio_wdmask(KM_DPAXE_RST, true);
+ /*
+ * PEXSW_RST:
+ * reset at power-up and unit reset only, deassert reset w/o WD
+ */
+ qrio_prstcfg(KM_PEXSW_RST, PRSTCFG_POWUP_UNIT_RST);
+ qrio_prst(KM_PEXSW_RST, false, false);
+ /*
+ * PEXSW_NT_RST:
+ * reset at power-up and unit reset only, deassert reset w/o WD
+ */
+ qrio_prstcfg(KM_PEXSW_NT_RST, PRSTCFG_POWUP_UNIT_RST);
+ qrio_prst(KM_PEXSW_NT_RST, false, false);
+ /*
+ * BOBCAT_RST:
+ * reset at power-up and unit reset only, deassert reset w/o WD
+ */
+ qrio_prstcfg(KM_BOBCAT_RST, PRSTCFG_POWUP_UNIT_RST);
+ qrio_prst(KM_BOBCAT_RST, false, false);
+ /*
+ * FEMT_RST:
+ * reset at power-up and unit reset only and enable WD
+ */
+ qrio_prstcfg(KM_FEMT_RST, PRSTCFG_POWUP_UNIT_RST);
+ qrio_wdmask(KM_FEMT_RST, true);
+ /*
+ * FOAM_RST:
+ * reset at power-up and unit reset only and enable WD
+ */
+ qrio_prstcfg(KM_FOAM_RST, PRSTCFG_POWUP_UNIT_RST);
+ qrio_wdmask(KM_FOAM_RST, true);
+
+ return 0;
+}
+
+int board_early_init_r(void)
+{
+ int ret = 0;
+
+ const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
+ int flash_esel = find_tlb_idx((void *)flashbase, 1);
+
+ /*
+ * Remap Boot flash region to caching-inhibited
+ * so that flash can be erased properly.
+ */
+
+ /* Flush d-cache and invalidate i-cache of any FLASH data */
+ flush_dcache();
+ invalidate_icache();
+
+ if (flash_esel == -1) {
+ /* very unlikely unless something is messed up */
+ puts("Error: Could not find TLB for FLASH BASE\n");
+ flash_esel = 2; /* give our best effort to continue */
+ } else {
+ /* invalidate existing TLB entry for flash */
+ disable_tlb(flash_esel);
+ }
+
+ set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
+ MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+ 0, flash_esel, BOOKE_PAGESZ_256M, 1);
+
+ set_liodns();
+ setup_qbman_portals();
+
+ qrio_set_leds();
+
+ /* enable Application Buffer */
+ qrio_enable_app_buffer();
+
+ return ret;
+}
+
+unsigned long get_serial_clock(unsigned long dummy)
+{
+ return (gd->bus_clk / 2);
+}
+
+unsigned long get_board_sys_clk(unsigned long dummy)
+{
+ return 66666666;
+}
+
+int misc_init_f(void)
+{
+ /* configure QRIO pis for i2c deblocking */
+ i2c_deblock_gpio_cfg();
+
+ /*
+ * CFE_RST (front phy):
+ * reset at power-up, unit and core reset, deasset reset w/o WD
+ */
+ qrio_prstcfg(KM_CFE_RST, PRSTCFG_POWUP_UNIT_CORE_RST);
+ qrio_prst(KM_CFE_RST, false, false);
+
+ /*
+ * ZL30158_RST (PTP clock generator):
+ * reset at power-up only, deassert reset and enable WD on it
+ */
+ qrio_prstcfg(KM_ZL30158_RST, PRSTCFG_POWUP_RST);
+ qrio_prst(KM_ZL30158_RST, false, false);
+
+ /*
+ * ZL30364_RST (EEC generator):
+ * reset at power-up only, deassert reset and enable WD on it
+ */
+ qrio_prstcfg(KM_ZL30364_RST, PRSTCFG_POWUP_RST);
+ qrio_prst(KM_ZL30364_RST, false, false);
+
+ return 0;
+}
+
+#define USED_SRDS_BANK 0
+#define EXPECTED_SRDS_RFCK SRDS_PLLCR0_RFCK_SEL_100
+
+#define BRG01_IOCLK12 0x02000000
+#define EC2_GTX_CLK125 0x08000000
+
+int misc_init_r(void)
+{
+ serdes_corenet_t *regs = (void *)CONFIG_SYS_FSL_CORENET_SERDES_ADDR;
+ struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_MPC85xx_SCFG;
+ ccsr_gur_t __iomem *gur = (ccsr_gur_t __iomem *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+
+ /* check SERDES bank 0 reference clock */
+ u32 actual = in_be32(®s->bank[USED_SRDS_BANK].pllcr0);
+
+ if (actual & SRDS_PLLCR0_POFF)
+ printf("Warning: SERDES bank %u pll is off\n", USED_SRDS_BANK);
+ if ((actual & SRDS_PLLCR0_RFCK_SEL_MASK) != EXPECTED_SRDS_RFCK) {
+ printf("Warning: SERDES bank %u expects %sMHz clock, is %sMHz\n",
+ USED_SRDS_BANK,
+ serdes_clock_to_string(EXPECTED_SRDS_RFCK),
+ serdes_clock_to_string(actual));
+ }
+
+ /* QE IO clk : BRG01 is used over clk12 for HDLC clk (20 MhZ) */
+ out_be32(&scfg->qeioclkcr,
+ in_be32(&scfg->qeioclkcr) | BRG01_IOCLK12);
+
+ ivm_read_eeprom(ivm_content, CONFIG_SYS_IVM_EEPROM_MAX_LEN,
+ CONFIG_PIGGY_MAC_ADDRESS_OFFSET);
+
+ /* Fix polarity of Card Detect and Write Protect */
+ out_be32(&gur->sdhcpcr, 0xFFFFFFFF);
+
+ /*
+ * EC1 is disabled in our design, so we must explicitly set GTXCLKSEL
+ * to EC2
+ */
+ out_be32(&scfg->emiiocr, in_be32(&scfg->emiiocr) | EC2_GTX_CLK125);
+
+ return 0;
+}
+
+int hush_init_var(void)
+{
+ ivm_analyze_eeprom(ivm_content, CONFIG_SYS_IVM_EEPROM_MAX_LEN);
+ return 0;
+}
+
+int last_stage_init(void)
+{
+ const char *kmem;
+ /* DIP switch support on BFTIC */
+ struct bfticu_iomap *bftic4 =
+ (struct bfticu_iomap *)SYS_BFTIC_BASE;
+ u8 dip_switch = in_8((u8 *)&bftic4->mswitch) & BFTICU_DIPSWITCH_MASK;
+
+ if (dip_switch != 0) {
+ /* start bootloader */
+ puts("DIP: Enabled\n");
+ env_set("actual_bank", "0");
+ }
+
+ set_km_env();
+
+ /*
+ * bootm_size is used to fixup the FDT memory node
+ * set it to kernelmem that has the same value
+ */
+ kmem = env_get("kernelmem");
+ if (kmem)
+ env_set("bootm_size", kmem);
+
+ return 0;
+}
+
+void fdt_fixup_fman_mac_addresses(void *blob)
+{
+ int node, ret;
+ char path[24];
+ unsigned char mac_addr[6];
+
+ /*
+ * Just the fm1-mac5 must be set by us, u-boot handle the 2 others,
+ * get the mac addr from env
+ */
+ if (!eth_env_get_enetaddr_by_index("eth", 4, mac_addr)) {
+ printf("eth4addr env variable not defined\n");
+ return;
+ }
+
+ /* local management port */
+ strcpy(path, "/soc/fman/ethernet@e8000");
+ node = fdt_path_offset(blob, path);
+ if (node < 0) {
+ printf("no %s\n", path);
+ return;
+ }
+
+ ret = fdt_setprop(blob, node, "local-mac-address", mac_addr, 6);
+ if (ret) {
+ printf("%s\n\terror setting local-mac-address property\n",
+ path);
+ }
+}
+
+int ft_board_setup(void *blob, struct bd_info *bd)
+{
+ phys_addr_t base;
+ phys_size_t size;
+
+ ft_cpu_setup(blob, bd);
+
+ base = env_get_bootm_low();
+ size = env_get_bootm_size();
+
+ fdt_fixup_memory(blob, (u64)base, (u64)size);
+
+ fdt_fixup_liodn(blob);
+
+ fdt_fixup_fman_mac_addresses(blob);
+
+ if (hwconfig("qe-tdm"))
+ fdt_del_diu(blob);
+ return 0;
+}
+
+/* DIC26_SELFTEST GPIO used to start factory test sw */
+#define SELFTEST_PORT QRIO_GPIO_A
+#define SELFTEST_PIN 0
+
+int post_hotkeys_pressed(void)
+{
+ qrio_gpio_direction_input(SELFTEST_PORT, SELFTEST_PIN);
+ return qrio_get_gpio(SELFTEST_PORT, SELFTEST_PIN);
+}
diff --git a/board/keymile/kmcent2/law.c b/board/keymile/kmcent2/law.c
new file mode 100644
index 0000000..aa0f29f
--- /dev/null
+++ b/board/keymile/kmcent2/law.c
@@ -0,0 +1,23 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * (C) Copyright 2016 Keymile AG
+ * Rainer Boschung <rainer.boschung@keymile.com>
+ *
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ */
+
+#include <config.h>
+#include <asm/fsl_law.h>
+
+struct law_entry law_table[] = {
+ SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_BMAN),
+ SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN),
+ SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_4M, LAW_TRGT_IF_DCSR),
+ SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_64M, LAW_TRGT_IF_IFC),
+ SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_IFC),
+ SET_LAW(CONFIG_SYS_QRIO_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_IFC),
+ SET_LAW(SYS_LAWAPP_BASE_PHYS, LAW_SIZE_512M, LAW_TRGT_IF_IFC),
+/* other application LAW are not used in u-boot */
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/keymile/kmcent2/tlb.c b/board/keymile/kmcent2/tlb.c
new file mode 100644
index 0000000..dbd3b9b
--- /dev/null
+++ b/board/keymile/kmcent2/tlb.c
@@ -0,0 +1,104 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * (C) Copyright 2016 Keymile AG
+ * Rainer Boschung <rainer.boschung@keymile.com>
+ *
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ */
+
+#include <asm/mmu.h>
+#include <asm/u-boot.h>
+
+struct fsl_e_tlb_entry tlb_table[] = {
+ /* TLB 0 - for temp stack in cache */
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS,
+ MAS3_SX | MAS3_SW | MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024,
+ MAS3_SX | MAS3_SW | MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024,
+ MAS3_SX | MAS3_SW | MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024,
+ MAS3_SX | MAS3_SW | MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+
+ /* TLB 1 */
+ /* *I*** - Covers boot page */
+ SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
+ MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+ 0, 0, BOOKE_PAGESZ_4K, 1),
+
+ /* *I*G* - CCSRBAR */
+ SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
+ MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+ 0, 1, BOOKE_PAGESZ_16M, 1),
+
+ /* *I*G* - Flash, localbus */
+ /* This will be changed to *I*G* after relocation to RAM. */
+ SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
+ MAS3_SX | MAS3_SR, MAS2_W | MAS2_G,
+ 0, 2, BOOKE_PAGESZ_128M, 1),
+
+ /* *I*G* - PCI1 */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
+ MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+ 0, 3, BOOKE_PAGESZ_1G, 1),
+
+ /* *I*G* - PCI1 I/O */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS,
+ MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+ 0, 4, BOOKE_PAGESZ_256K, 1),
+
+ /* Bman/Qman */
+ SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS,
+ MAS3_SX | MAS3_SW | MAS3_SR, 0,
+ 0, 5, BOOKE_PAGESZ_16M, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x01000000,
+ CONFIG_SYS_BMAN_MEM_PHYS + 0x01000000,
+ MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+ 0, 6, BOOKE_PAGESZ_16M, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS,
+ MAS3_SX | MAS3_SW | MAS3_SR, 0,
+ 0, 7, BOOKE_PAGESZ_16M, 1),
+ SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x01000000,
+ CONFIG_SYS_QMAN_MEM_PHYS + 0x01000000,
+ MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+ 0, 8, BOOKE_PAGESZ_16M, 1),
+
+ SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
+ MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+ 0, 9, BOOKE_PAGESZ_4M, 1),
+
+ /* *I*G - NAND */
+ SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
+ MAS3_SX | MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+ 0, 10, BOOKE_PAGESZ_64K, 1),
+ /* QRIO */
+ SET_TLB_ENTRY(1, CONFIG_SYS_QRIO_BASE, CONFIG_SYS_QRIO_BASE_PHYS,
+ MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+ 0, 11, BOOKE_PAGESZ_64K, 1),
+ /* MRAM */
+ SET_TLB_ENTRY(1, CONFIG_SYS_MRAM_BASE, SYS_MRAM_BASE_PHYS,
+ MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+ 0, 12, BOOKE_PAGESZ_128M, 1),
+ /* BFTIC */
+ SET_TLB_ENTRY(1, SYS_BFTIC_BASE, SYS_BFTIC_BASE_PHYS,
+ MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+ 0, 13, BOOKE_PAGESZ_128M, 1),
+ /*
+ * entry 14 and 15 has been used hard coded, they will be disabled
+ * in cpu_init_f, so do not use them here!!.
+ */
+ /* PAXE */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PAXE_BASE, SYS_PAXE_BASE_PHYS,
+ MAS3_SW | MAS3_SR, MAS2_I | MAS2_G,
+ 0, 16, BOOKE_PAGESZ_128M, 1)
+};
+
+int num_tlb_entries = ARRAY_SIZE(tlb_table);