ARM: dts: stm32mp1: sync device tree with v5.2-rc4
Synchronize device tree with v5.2-rc4 label and
update the associated u-boot dtsi.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Pierre-Jean Texier <pjtexier@koncepto.io>
diff --git a/arch/arm/dts/stm32mp157c.dtsi b/arch/arm/dts/stm32mp157c.dtsi
index b9f0eac..d15fba0 100644
--- a/arch/arm/dts/stm32mp157c.dtsi
+++ b/arch/arm/dts/stm32mp157c.dtsi
@@ -35,28 +35,6 @@
cpu_on = <0x84000003>;
};
- aliases {
- gpio0 = &gpioa;
- gpio1 = &gpiob;
- gpio2 = &gpioc;
- gpio3 = &gpiod;
- gpio4 = &gpioe;
- gpio5 = &gpiof;
- gpio6 = &gpiog;
- gpio7 = &gpioh;
- gpio8 = &gpioi;
- gpio9 = &gpioj;
- gpio10 = &gpiok;
- serial0 = &usart1;
- serial1 = &usart2;
- serial2 = &usart3;
- serial3 = &uart4;
- serial4 = &uart5;
- serial5 = &usart6;
- serial6 = &uart7;
- serial7 = &uart8;
- };
-
intc: interrupt-controller@a0021000 {
compatible = "arm,cortex-a7-gic";
#interrupt-cells = <3>;
@@ -106,6 +84,38 @@
};
};
+ thermal-zones {
+ cpu_thermal: cpu-thermal {
+ polling-delay-passive = <0>;
+ polling-delay = <0>;
+ thermal-sensors = <&dts>;
+
+ trips {
+ cpu_alert1: cpu-alert1 {
+ temperature = <85000>;
+ hysteresis = <0>;
+ type = "passive";
+ };
+
+ cpu-crit {
+ temperature = <120000>;
+ hysteresis = <0>;
+ type = "critical";
+ };
+ };
+
+ cooling-maps {
+ };
+ };
+ };
+
+ reboot {
+ compatible = "syscon-reboot";
+ regmap = <&rcc>;
+ offset = <0x404>;
+ mask = <0x1>;
+ };
+
soc {
compatible = "simple-bus";
#address-cells = <1>;
@@ -120,6 +130,12 @@
reg = <0x40000000 0x400>;
clocks = <&rcc TIM2_K>;
clock-names = "int";
+ dmas = <&dmamux1 18 0x400 0x1>,
+ <&dmamux1 19 0x400 0x1>,
+ <&dmamux1 20 0x400 0x1>,
+ <&dmamux1 21 0x400 0x1>,
+ <&dmamux1 22 0x400 0x1>;
+ dma-names = "ch1", "ch2", "ch3", "ch4", "up";
status = "disabled";
pwm {
@@ -141,6 +157,13 @@
reg = <0x40001000 0x400>;
clocks = <&rcc TIM3_K>;
clock-names = "int";
+ dmas = <&dmamux1 23 0x400 0x1>,
+ <&dmamux1 24 0x400 0x1>,
+ <&dmamux1 25 0x400 0x1>,
+ <&dmamux1 26 0x400 0x1>,
+ <&dmamux1 27 0x400 0x1>,
+ <&dmamux1 28 0x400 0x1>;
+ dma-names = "ch1", "ch2", "ch3", "ch4", "up", "trig";
status = "disabled";
pwm {
@@ -162,6 +185,11 @@
reg = <0x40002000 0x400>;
clocks = <&rcc TIM4_K>;
clock-names = "int";
+ dmas = <&dmamux1 29 0x400 0x1>,
+ <&dmamux1 30 0x400 0x1>,
+ <&dmamux1 31 0x400 0x1>,
+ <&dmamux1 32 0x400 0x1>;
+ dma-names = "ch1", "ch2", "ch3", "ch4";
status = "disabled";
pwm {
@@ -183,6 +211,13 @@
reg = <0x40003000 0x400>;
clocks = <&rcc TIM5_K>;
clock-names = "int";
+ dmas = <&dmamux1 55 0x400 0x1>,
+ <&dmamux1 56 0x400 0x1>,
+ <&dmamux1 57 0x400 0x1>,
+ <&dmamux1 58 0x400 0x1>,
+ <&dmamux1 59 0x400 0x1>,
+ <&dmamux1 60 0x400 0x1>;
+ dma-names = "ch1", "ch2", "ch3", "ch4", "up", "trig";
status = "disabled";
pwm {
@@ -204,6 +239,8 @@
reg = <0x40004000 0x400>;
clocks = <&rcc TIM6_K>;
clock-names = "int";
+ dmas = <&dmamux1 69 0x400 0x1>;
+ dma-names = "up";
status = "disabled";
timer@5 {
@@ -220,6 +257,8 @@
reg = <0x40005000 0x400>;
clocks = <&rcc TIM7_K>;
clock-names = "int";
+ dmas = <&dmamux1 70 0x400 0x1>;
+ dma-names = "up";
status = "disabled";
timer@6 {
@@ -347,6 +386,19 @@
status = "disabled";
};
+ spdifrx: audio-controller@4000d000 {
+ compatible = "st,stm32h7-spdifrx";
+ #sound-dai-cells = <0>;
+ reg = <0x4000d000 0x400>;
+ clocks = <&rcc SPDIF_K>;
+ clock-names = "kclk";
+ interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&dmamux1 93 0x400 0x01>,
+ <&dmamux1 94 0x400 0x01>;
+ dma-names = "rx", "rx-ctrl";
+ status = "disabled";
+ };
+
usart2: serial@4000e000 {
compatible = "st,stm32h7-uart";
reg = <0x4000e000 0x400>;
@@ -487,6 +539,15 @@
reg = <0x44000000 0x400>;
clocks = <&rcc TIM1_K>;
clock-names = "int";
+ dmas = <&dmamux1 11 0x400 0x1>,
+ <&dmamux1 12 0x400 0x1>,
+ <&dmamux1 13 0x400 0x1>,
+ <&dmamux1 14 0x400 0x1>,
+ <&dmamux1 15 0x400 0x1>,
+ <&dmamux1 16 0x400 0x1>,
+ <&dmamux1 17 0x400 0x1>;
+ dma-names = "ch1", "ch2", "ch3", "ch4",
+ "up", "trig", "com";
status = "disabled";
pwm {
@@ -508,6 +569,15 @@
reg = <0x44001000 0x400>;
clocks = <&rcc TIM8_K>;
clock-names = "int";
+ dmas = <&dmamux1 47 0x400 0x1>,
+ <&dmamux1 48 0x400 0x1>,
+ <&dmamux1 49 0x400 0x1>,
+ <&dmamux1 50 0x400 0x1>,
+ <&dmamux1 51 0x400 0x1>,
+ <&dmamux1 52 0x400 0x1>,
+ <&dmamux1 53 0x400 0x1>;
+ dma-names = "ch1", "ch2", "ch3", "ch4",
+ "up", "trig", "com";
status = "disabled";
pwm {
@@ -565,6 +635,11 @@
reg = <0x44006000 0x400>;
clocks = <&rcc TIM15_K>;
clock-names = "int";
+ dmas = <&dmamux1 105 0x400 0x1>,
+ <&dmamux1 106 0x400 0x1>,
+ <&dmamux1 107 0x400 0x1>,
+ <&dmamux1 108 0x400 0x1>;
+ dma-names = "ch1", "up", "trig", "com";
status = "disabled";
pwm {
@@ -586,6 +661,9 @@
reg = <0x44007000 0x400>;
clocks = <&rcc TIM16_K>;
clock-names = "int";
+ dmas = <&dmamux1 109 0x400 0x1>,
+ <&dmamux1 110 0x400 0x1>;
+ dma-names = "ch1", "up";
status = "disabled";
pwm {
@@ -606,6 +684,9 @@
reg = <0x44008000 0x400>;
clocks = <&rcc TIM17_K>;
clock-names = "int";
+ dmas = <&dmamux1 111 0x400 0x1>,
+ <&dmamux1 112 0x400 0x1>;
+ dma-names = "ch1", "up";
status = "disabled";
pwm {
@@ -706,14 +787,14 @@
m_can1: can@4400e000 {
compatible = "bosch,m_can";
- reg = <0x4400e000 0x400>, <0x44011000 0x2800>;
+ reg = <0x4400e000 0x400>, <0x44011000 0x1400>;
reg-names = "m_can", "message_ram";
interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "int0", "int1";
clocks = <&rcc CK_HSE>, <&rcc FDCAN_K>;
clock-names = "hclk", "cclk";
- bosch,mram-cfg = <0x0 0 0 32 0 0 2 2>;
+ bosch,mram-cfg = <0x1400 0 0 32 0 0 2 2>;
status = "disabled";
};
@@ -811,13 +892,14 @@
};
sdmmc3: sdmmc@48004000 {
- compatible = "st,stm32-sdmmc2";
- reg = <0x48004000 0x400>, <0x48005000 0x400>;
- reg-names = "sdmmc", "delay";
+ compatible = "arm,pl18x", "arm,primecell";
+ arm,primecell-periphid = <0x10153180>;
+ reg = <0x48004000 0x400>;
+ reg-names = "sdmmc";
interrupts = <GIC_SPI 137 IRQ_TYPE_NONE>;
clocks = <&rcc SDMMC3_K>;
+ clock-names = "apb_pclk";
resets = <&rcc SDMMC3_R>;
- st,idma = <1>;
cap-sd-highspeed;
cap-mmc-highspeed;
max-frequency = <120000000>;
@@ -825,7 +907,7 @@
};
usbotg_hs: usb-otg@49000000 {
- compatible = "st,stm32mp1-hsotg", "snps,dwc2";
+ compatible = "snps,dwc2";
reg = <0x49000000 0x10000>;
clocks = <&rcc USBO_K>;
clock-names = "otg";
@@ -846,7 +928,6 @@
reg = <0x4c000000 0x400>;
clocks = <&rcc HSEM>;
clock-names = "hwspinlock";
- status = "disabled";
};
ipcc: mailbox@4c001000 {
@@ -856,9 +937,11 @@
st,proc-id = <0>;
interrupts-extended =
<&intc GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
- <&intc GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
- interrupt-names = "rx", "tx";
+ <&intc GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+ <&exti 61 1>;
+ interrupt-names = "rx", "tx", "wakeup";
clocks = <&rcc IPCC>;
+ wakeup-source;
status = "disabled";
};
@@ -869,13 +952,6 @@
#reset-cells = <1>;
};
- rcc_reboot: rcc-reboot@50000000 {
- compatible = "syscon-reboot";
- regmap = <&rcc>;
- offset = <0x404>;
- mask = <0x1>;
- };
-
pwr: pwr@50001000 {
compatible = "st,stm32mp1-pwr", "st,stm32-pwr", "syscon", "simple-mfd";
reg = <0x50001000 0x400>;
@@ -885,7 +961,7 @@
clocks = <&rcc PLL2_R>;
clock-names = "phyclk";
- pwr-regulators@c {
+ pwr-regulators {
compatible = "st,stm32mp1,pwr-reg";
st,tzcr = <&rcc 0x0 0x1>;
@@ -919,6 +995,7 @@
syscfg: syscon@50020000 {
compatible = "st,stm32mp157-syscfg", "syscon";
reg = <0x50020000 0x400>;
+ clocks = <&rcc SYSCFG>;
};
lptimer2: timer@50021000 {
@@ -1007,6 +1084,16 @@
status = "disabled";
};
+ dts: thermal@50028000 {
+ compatible = "st,stm32-thermal";
+ reg = <0x50028000 0x100>;
+ interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&rcc TMPSENS>;
+ clock-names = "pclk";
+ #thermal-sensor-cells = <0>;
+ status = "disabled";
+ };
+
cryp1: cryp@54001000 {
compatible = "st,stm32mp1-cryp";
reg = <0x54001000 0x400>;
@@ -1072,26 +1159,27 @@
};
sdmmc1: sdmmc@58005000 {
- compatible = "st,stm32-sdmmc2";
- reg = <0x58005000 0x1000>, <0x58006000 0x1000>;
- reg-names = "sdmmc", "delay";
+ compatible = "arm,pl18x", "arm,primecell";
+ arm,primecell-periphid = <0x10153180>;
+ reg = <0x58005000 0x1000>;
+ interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "cmd_irq";
clocks = <&rcc SDMMC1_K>;
+ clock-names = "apb_pclk";
resets = <&rcc SDMMC1_R>;
- st,idma = <1>;
cap-sd-highspeed;
cap-mmc-highspeed;
max-frequency = <120000000>;
- status = "disabled";
};
sdmmc2: sdmmc@58007000 {
- compatible = "st,stm32-sdmmc2";
- reg = <0x58007000 0x1000>, <0x58008000 0x1000>;
- reg-names = "sdmmc", "delay";
+ compatible = "arm,pl18x", "arm,primecell";
+ arm,primecell-periphid = <0x10153180>;
+ reg = <0x58007000 0x1000>;
interrupts = <GIC_SPI 124 IRQ_TYPE_NONE>;
clocks = <&rcc SDMMC2_K>;
+ clock-names = "apb_pclk";
resets = <&rcc SDMMC2_R>;
- st,idma = <1>;
cap-sd-highspeed;
cap-mmc-highspeed;
max-frequency = <120000000>;
@@ -1115,25 +1203,21 @@
compatible = "st,stm32mp1-dwmac", "snps,dwmac-4.20a";
reg = <0x5800a000 0x2000>;
reg-names = "stmmaceth";
- interrupts-extended =
- <&intc GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>,
- <&intc GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>,
- <&exti 70 1>;
- interrupt-names = "macirq",
- "eth_wake_irq",
- "stm32_pwr_wakeup";
+ interrupts-extended = <&intc GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
clock-names = "stmmaceth",
"mac-clk-tx",
"mac-clk-rx",
- "ethstp";
+ "ethstp",
+ "syscfg-clk";
clocks = <&rcc ETHMAC>,
<&rcc ETHTX>,
<&rcc ETHRX>,
- <&rcc ETHSTP>;
+ <&rcc ETHSTP>,
+ <&rcc SYSCFG>;
st,syscon = <&syscfg 0x4>;
snps,mixed-burst;
snps,pbl = <2>;
- snps,en-tx-lpi-clockgating;
snps,axi-config = <&stmmac_axi_config_0>;
snps,tso;
status = "disabled";
@@ -1258,6 +1342,12 @@
reg = <0x5c005000 0x400>;
#address-cells = <1>;
#size-cells = <1>;
+ ts_cal1: calib@5c {
+ reg = <0x5c 0x2>;
+ };
+ ts_cal2: calib@5e {
+ reg = <0x5e 0x2>;
+ };
};
i2c6: i2c@5c009000 {