board/BuR/common: move I2C initialization from common part to board-specific
At this time I2C and responsible pin-mux is setup during PMIC initialziation
within common.c, this is possible because today PMIC is always connected on
I2C0.
In Future this will be changed, PMIC isn't anymore connected to bus0 in call
cases.
So we do following:
- rename enable_i2c_pin_mux0 to enable_i2c_pin_mux to be generic for enabling
pin-mux on different or more busses.
- move the call to i2c_pin_mux and i2c_init from common.c to the specific
board.c
Signed-off-by: Hannes Petermaier <hannes.petermaier@br-automation.com>
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
diff --git a/board/BuR/common/bur_common.h b/board/BuR/common/bur_common.h
index 39afbba..3061e4c 100644
--- a/board/BuR/common/bur_common.h
+++ b/board/BuR/common/bur_common.h
@@ -19,7 +19,7 @@
void blink(u32 blinks, u32 intervall, u32 pin);
void pmicsetup(u32 mpupll);
void enable_uart0_pin_mux(void);
-void enable_i2c0_pin_mux(void);
+void enable_i2c_pin_mux(void);
void enable_board_pin_mux(void);
int board_eth_init(bd_t *bis);
diff --git a/board/BuR/common/common.c b/board/BuR/common/common.c
index 5ff8a7e..91834eb 100644
--- a/board/BuR/common/common.c
+++ b/board/BuR/common/common.c
@@ -461,10 +461,6 @@
int mpu_vdd;
int usb_cur_lim;
- /* setup I2C */
- enable_i2c0_pin_mux();
- i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);
-
if (i2c_probe(TPS65217_CHIP_PM)) {
puts("PMIC (0x24) not found! skip further initalization.\n");
return;
diff --git a/board/BuR/kwb/board.c b/board/BuR/kwb/board.c
index 892311e..6eed7e0 100644
--- a/board/BuR/kwb/board.c
+++ b/board/BuR/kwb/board.c
@@ -124,7 +124,8 @@
gpio_direction_output(LCD_PWR, 0);
/* setup I2C */
- enable_i2c0_pin_mux();
+ enable_i2c_pin_mux();
+ i2c_set_bus_num(0);
i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);
/* power-ON 3V3 via Resetcontroller */
diff --git a/board/BuR/kwb/mux.c b/board/BuR/kwb/mux.c
index 9f89b5e..2b1d8d3 100644
--- a/board/BuR/kwb/mux.c
+++ b/board/BuR/kwb/mux.c
@@ -180,7 +180,7 @@
configure_module_pin_mux(uart0_pin_mux);
}
-void enable_i2c0_pin_mux(void)
+void enable_i2c_pin_mux(void)
{
configure_module_pin_mux(i2c0_pin_mux);
}
diff --git a/board/BuR/tseries/board.c b/board/BuR/tseries/board.c
index 9402aa4..89e989f 100644
--- a/board/BuR/tseries/board.c
+++ b/board/BuR/tseries/board.c
@@ -123,6 +123,10 @@
/* setup LCD-Pixel Clock */
writel(0x2, &cmdpll->clklcdcpixelclk); /* clock comes from perPLL M2 */
+ /* setup I2C */
+ enable_i2c_pin_mux();
+ i2c_set_bus_num(0);
+ i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE);
pmicsetup(0);
}
diff --git a/board/BuR/tseries/mux.c b/board/BuR/tseries/mux.c
index 2c87a63..ac7e885 100644
--- a/board/BuR/tseries/mux.c
+++ b/board/BuR/tseries/mux.c
@@ -226,7 +226,7 @@
configure_module_pin_mux(uart0_pin_mux);
}
-void enable_i2c0_pin_mux(void)
+void enable_i2c_pin_mux(void)
{
configure_module_pin_mux(i2c0_pin_mux);
}