ppc4xx: Big cleanup of PPC4xx defines
This patch cleans up multiple issues of the 4xx register (mostly
DCR, SDR, CPR, etc) definitions:
- Change lower case defines to upper case (plb4_acr -> PLB4_ACR)
- Change the defines to better match the names from the
user's manuals (e.g. cprpllc -> CPR0_PLLC)
- Removal of some unused defines
Please test this patch intensive on your PPC4xx platform. Even though
I tried not to break anything and tested successfully on multiple
4xx AMCC platforms, testing on custom platforms is recommended.
Signed-off-by: Stefan Roese <sr@denx.de>
diff --git a/board/amcc/acadia/acadia.c b/board/amcc/acadia/acadia.c
index 8d79be2..0db6199 100644
--- a/board/amcc/acadia/acadia.c
+++ b/board/amcc/acadia/acadia.c
@@ -57,7 +57,7 @@
#if !defined(CONFIG_NAND_U_BOOT)
/* don't reinit PLL when booting via I2C bootstrap option */
- mfsdr(SDR_PINSTP, reg);
+ mfsdr(SDR0_PINSTP, reg);
if (reg != 0xf0000000)
board_pll_init_f();
#endif
@@ -65,18 +65,18 @@
acadia_gpio_init();
/* Configure 405EZ for NAND usage */
- mtsdr(sdrnand0, SDR_NAND0_NDEN | SDR_NAND0_NDAREN | SDR_NAND0_NDRBEN);
- mfsdr(sdrultra0, reg);
+ mtsdr(SDR0_NAND0, SDR_NAND0_NDEN | SDR_NAND0_NDAREN | SDR_NAND0_NDRBEN);
+ mfsdr(SDR0_ULTRA0, reg);
reg &= ~SDR_ULTRA0_CSN_MASK;
reg |= (SDR_ULTRA0_CSNSEL0 >> CONFIG_SYS_NAND_CS) |
SDR_ULTRA0_NDGPIOBP |
SDR_ULTRA0_EBCRDYEN |
SDR_ULTRA0_NFSRSTEN;
- mtsdr(sdrultra0, reg);
+ mtsdr(SDR0_ULTRA0, reg);
/* USB Host core needs this bit set */
- mfsdr(sdrultra1, reg);
- mtsdr(sdrultra1, reg | SDR_ULTRA1_LEDNENABLE);
+ mfsdr(SDR0_ULTRA1, reg);
+ mtsdr(SDR0_ULTRA1, reg | SDR_ULTRA1_LEDNENABLE);
mtdcr(uicsr, 0xFFFFFFFF); /* clear all ints */
mtdcr(uicer, 0x00000000); /* disable all ints */
diff --git a/board/amcc/acadia/memory.c b/board/amcc/acadia/memory.c
index 3e5c80e..8c2addc 100644
--- a/board/amcc/acadia/memory.c
+++ b/board/amcc/acadia/memory.c
@@ -65,7 +65,7 @@
u32 reg;
/* don't reinit PLL when booting via I2C bootstrap option */
- mfsdr(SDR_PINSTP, reg);
+ mfsdr(SDR0_PINSTP, reg);
if (reg != 0xf0000000)
board_pll_init_f();
#endif
@@ -81,25 +81,25 @@
gpio_config(CONFIG_SYS_GPIO_CRAM_WAIT, GPIO_IN, GPIO_SEL, GPIO_OUT_NO_CHG);
/* 2. EBC in Async mode */
- mtebc(pb1ap, 0x078F1EC0);
- mtebc(pb2ap, 0x078F1EC0);
- mtebc(pb1cr, 0x000BC000);
- mtebc(pb2cr, 0x020BC000);
+ mtebc(PB1AP, 0x078F1EC0);
+ mtebc(PB2AP, 0x078F1EC0);
+ mtebc(PB1CR, 0x000BC000);
+ mtebc(PB2CR, 0x020BC000);
/* 3. Set CRAM in Sync mode */
cram_bcr_write(0x7012); /* CRAM burst setting */
/* 4. EBC in Sync mode */
- mtebc(pb1ap, 0x9C0201C0);
- mtebc(pb2ap, 0x9C0201C0);
+ mtebc(PB1AP, 0x9C0201C0);
+ mtebc(PB2AP, 0x9C0201C0);
/* Set GPIO pins back to alternate function */
gpio_config(CONFIG_SYS_GPIO_CRAM_CLK, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG);
gpio_config(CONFIG_SYS_GPIO_CRAM_ADV, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG);
/* Config EBC to use RDY */
- mfsdr(sdrultra0, val);
- mtsdr(sdrultra0, val | SDR_ULTRA0_EBCRDYEN);
+ mfsdr(SDR0_ULTRA0, val);
+ mtsdr(SDR0_ULTRA0, val | SDR_ULTRA0_EBCRDYEN);
/* Wait a short while, since for NAND booting this is too fast */
for (i=0; i<200000; i++)
diff --git a/board/amcc/acadia/pll.c b/board/amcc/acadia/pll.c
index 9dcce35..b63813c 100644
--- a/board/amcc/acadia/pll.c
+++ b/board/amcc/acadia/pll.c
@@ -51,11 +51,11 @@
*/
/* Initialize PLL */
- mtcpr(cprpllc, 0x0000033c);
- mtcpr(cprplld, 0x0c010200);
- mtcpr(cprprimad, 0x04060c0c);
- mtcpr(cprperd0, 0x000c0000); /* SPI clk div. eq. OPB clk div. */
- mtcpr(cprclkupd, 0x40000000);
+ mtcpr(CPR0_PLLC, 0x0000033c);
+ mtcpr(CPR0_PLLD, 0x0c010200);
+ mtcpr(CPC0_PRIMAD, 0x04060c0c);
+ mtcpr(CPC0_PERD0, 0x000c0000); /* SPI clk div. eq. OPB clk div. */
+ mtcpr(CPR0_CLKUP, 0x40000000);
}
#elif defined(PLLMR0_266_160_80)
@@ -83,13 +83,13 @@
*/
/* Initialize PLL */
- mtcpr(cprpllc, 0x20000238);
- mtcpr(cprplld, 0x03010400);
- mtcpr(cprprimad, 0x03050a0a);
- mtcpr(cprperc0, 0x00000000);
- mtcpr(cprperd0, 0x070a0707); /* SPI clk div. eq. OPB clk div. */
- mtcpr(cprperd1, 0x07323200);
- mtcpr(cprclkupd, 0x40000000);
+ mtcpr(CPR0_PLLC, 0x20000238);
+ mtcpr(CPR0_PLLD, 0x03010400);
+ mtcpr(CPC0_PRIMAD, 0x03050a0a);
+ mtcpr(CPC0_PERC0, 0x00000000);
+ mtcpr(CPC0_PERD0, 0x070a0707); /* SPI clk div. eq. OPB clk div. */
+ mtcpr(CPC0_PERD1, 0x07323200);
+ mtcpr(CPR0_CLKUP, 0x40000000);
}
#elif defined(PLLMR0_333_166_83)
@@ -117,12 +117,12 @@
*/
/* Initialize PLL */
- mtcpr(cprpllc, 0x0000033C);
- mtcpr(cprplld, 0x0a010000);
- mtcpr(cprprimad, 0x02040808);
- mtcpr(cprperd0, 0x02080505); /* SPI clk div. eq. OPB clk div. */
- mtcpr(cprperd1, 0xA6A60300);
- mtcpr(cprclkupd, 0x40000000);
+ mtcpr(CPR0_PLLC, 0x0000033C);
+ mtcpr(CPR0_PLLD, 0x0a010000);
+ mtcpr(CPC0_PRIMAD, 0x02040808);
+ mtcpr(CPC0_PERD0, 0x02080505); /* SPI clk div. eq. OPB clk div. */
+ mtcpr(CPC0_PERD1, 0xA6A60300);
+ mtcpr(CPR0_CLKUP, 0x40000000);
}
#elif defined(PLLMR0_100_100_12)
@@ -143,12 +143,12 @@
*/
/* Initialize PLL */
- mtcpr(cprpllc, 0x000003BC);
- mtcpr(cprplld, 0x06060600);
- mtcpr(cprprimad, 0x02020004);
- mtcpr(cprperd0, 0x04002828); /* SPI clk div. eq. OPB clk div. */
- mtcpr(cprperd1, 0xC8C81600);
- mtcpr(cprclkupd, 0x40000000);
+ mtcpr(CPR0_PLLC, 0x000003BC);
+ mtcpr(CPR0_PLLD, 0x06060600);
+ mtcpr(CPC0_PRIMAD, 0x02020004);
+ mtcpr(CPC0_PERD0, 0x04002828); /* SPI clk div. eq. OPB clk div. */
+ mtcpr(CPC0_PERD1, 0xC8C81600);
+ mtcpr(CPR0_CLKUP, 0x40000000);
}
#endif /* CPU_<speed>_405EZ */
@@ -167,12 +167,12 @@
/*
* Read PLL Mode registers
*/
- mfcpr(cprplld, cpr_plld);
+ mfcpr(CPR0_PLLD, cpr_plld);
/*
* Read CPR_PRIMAD register
*/
- mfcpr(cprprimad, cpr_primad);
+ mfcpr(CPC0_PRIMAD, cpr_primad);
/*
* Determine CPU clock frequency
diff --git a/board/amcc/bamboo/bamboo.c b/board/amcc/bamboo/bamboo.c
index febc61a..2ffd720 100644
--- a/board/amcc/bamboo/bamboo.c
+++ b/board/amcc/bamboo/bamboo.c
@@ -487,35 +487,35 @@
| Set priority for all PLB3 devices to 0.
| Set PLB3 arbiter to fair mode.
+-------------------------------------------------------------------------*/
- mfsdr(sdr_amp1, addr);
- mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(plb3_acr);
- mtdcr(plb3_acr, addr | 0x80000000);
+ mfsdr(SD0_AMP1, addr);
+ mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
+ addr = mfdcr(PLB3_ACR);
+ mtdcr(PLB3_ACR, addr | 0x80000000);
/*-------------------------------------------------------------------------+
| Set priority for all PLB4 devices to 0.
+-------------------------------------------------------------------------*/
- mfsdr(sdr_amp0, addr);
- mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(plb4_acr) | 0xa0000000; /* Was 0x8---- */
- mtdcr(plb4_acr, addr);
+ mfsdr(SD0_AMP0, addr);
+ mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
+ addr = mfdcr(PLB4_ACR) | 0xa0000000; /* Was 0x8---- */
+ mtdcr(PLB4_ACR, addr);
/*-------------------------------------------------------------------------+
| Set Nebula PLB4 arbiter to fair mode.
+-------------------------------------------------------------------------*/
/* Segment0 */
- addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair;
- addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled;
- addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep;
- addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep;
- mtdcr(plb0_acr, addr);
+ addr = (mfdcr(PLB0_ACR) & ~PLB0_ACR_PPM_MASK) | PLB0_ACR_PPM_FAIR;
+ addr = (addr & ~PLB0_ACR_HBU_MASK) | PLB0_ACR_HBU_ENABLED;
+ addr = (addr & ~PLB0_ACR_RDP_MASK) | PLB0_ACR_RDP_4DEEP;
+ addr = (addr & ~PLB0_ACR_WRP_MASK) | PLB0_ACR_WRP_2DEEP;
+ mtdcr(PLB0_ACR, addr);
/* Segment1 */
- addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair;
- addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled;
- addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep;
- addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep;
- mtdcr(plb1_acr, addr);
+ addr = (mfdcr(PLB1_ACR) & ~PLB1_ACR_PPM_MASK) | PLB1_ACR_PPM_FAIR;
+ addr = (addr & ~PLB1_ACR_HBU_MASK) | PLB1_ACR_HBU_ENABLED;
+ addr = (addr & ~PLB1_ACR_RDP_MASK) | PLB1_ACR_RDP_4DEEP;
+ addr = (addr & ~PLB1_ACR_WRP_MASK) | PLB1_ACR_WRP_2DEEP;
+ mtdcr(PLB1_ACR, addr);
return 1;
}
@@ -695,8 +695,8 @@
|
+-------------------------------------------------------------------------*/
/* NVRAM - FPGA */
- mtebc(pb5ap, EBC0_BNAP_NVRAM_FPGA);
- mtebc(pb5cr, EBC0_BNCR_NVRAM_FPGA_CS5);
+ mtebc(PB5AP, EBC0_BNAP_NVRAM_FPGA);
+ mtebc(PB5CR, EBC0_BNCR_NVRAM_FPGA_CS5);
/*-------------------------------------------------------------------------+
|
@@ -749,7 +749,7 @@
case SDR0_PSTRP0_BOOTSTRAP_IIC_A4_EN:
/* Boot Settings in IIC EEprom address 0xA8 or 0xA4 */
/* Read Serial Device Strap Register1 in PPC440EP */
- mfsdr(sdr_sdstp1, sdr0_sdstp1);
+ mfsdr(SDR0_SDSTP1, sdr0_sdstp1);
boot_selection = sdr0_sdstp1 & SDR0_SDSTP1_BOOT_SEL_MASK;
ebc_boot_size = sdr0_sdstp1 & SDR0_SDSTP1_EBC_ROM_BS_MASK;
@@ -822,7 +822,7 @@
/* Default Strap Settings 5-7 */
/* Boot Settings in IIC EEprom address 0xA8 or 0xA4 */
/* Read Serial Device Strap Register1 in PPC440EP */
- mfsdr(sdr_sdstp1, sdr0_sdstp1);
+ mfsdr(SDR0_SDSTP1, sdr0_sdstp1);
boot_selection = sdr0_sdstp1 & SDR0_SDSTP1_BOOT_SEL_MASK;
ebc_boot_size = sdr0_sdstp1 & SDR0_SDSTP1_EBC_ROM_BS_MASK;
@@ -1013,8 +1013,8 @@
/*-------------------------------------------------------------------------+
| Initialize EBC CONFIG
+-------------------------------------------------------------------------*/
- mtdcr(ebccfga, xbcfg);
- mtdcr(ebccfgd, EBC0_CFG_EBTC_DRIVEN |
+ mtdcr(EBC0_CFGADDR, EBC0_CFG);
+ mtdcr(EBC0_CFGDATA, EBC0_CFG_EBTC_DRIVEN |
EBC0_CFG_PTD_ENABLED |
EBC0_CFG_RTC_2048PERCLK |
EBC0_CFG_EMPL_LOW |
@@ -1029,20 +1029,20 @@
| Initialize EBC Bank 0-4
+-------------------------------------------------------------------------*/
/* EBC Bank0 */
- mtebc(pb0ap, ebc0_cs0_bnap_value);
- mtebc(pb0cr, ebc0_cs0_bncr_value);
+ mtebc(PB0AP, ebc0_cs0_bnap_value);
+ mtebc(PB0CR, ebc0_cs0_bncr_value);
/* EBC Bank1 */
- mtebc(pb1ap, ebc0_cs1_bnap_value);
- mtebc(pb1cr, ebc0_cs1_bncr_value);
+ mtebc(PB1AP, ebc0_cs1_bnap_value);
+ mtebc(PB1CR, ebc0_cs1_bncr_value);
/* EBC Bank2 */
- mtebc(pb2ap, ebc0_cs2_bnap_value);
- mtebc(pb2cr, ebc0_cs2_bncr_value);
+ mtebc(PB2AP, ebc0_cs2_bnap_value);
+ mtebc(PB2CR, ebc0_cs2_bncr_value);
/* EBC Bank3 */
- mtebc(pb3ap, ebc0_cs3_bnap_value);
- mtebc(pb3cr, ebc0_cs3_bncr_value);
+ mtebc(PB3AP, ebc0_cs3_bnap_value);
+ mtebc(PB3CR, ebc0_cs3_bncr_value);
/* EBC Bank4 */
- mtebc(pb4ap, ebc0_cs4_bnap_value);
- mtebc(pb4cr, ebc0_cs4_bncr_value);
+ mtebc(PB4AP, ebc0_cs4_bnap_value);
+ mtebc(PB4CR, ebc0_cs4_bncr_value);
return;
}
@@ -1939,10 +1939,10 @@
sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_UES_MASK) | SDR0_PFC1_UES_USB2D_SEL;
sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_UPR_MASK) | SDR0_PFC1_UPR_DISABLE;
- mfsdr(sdr_usb0, sdr0_usb0);
+ mfsdr(SDR0_USB0, sdr0_usb0);
sdr0_usb0 = sdr0_usb0 &~SDR0_USB0_USB_DEVSEL_MASK;
sdr0_usb0 = sdr0_usb0 | SDR0_USB0_USB20D_DEVSEL;
- mtsdr(sdr_usb0, sdr0_usb0);
+ mtsdr(SDR0_USB0, sdr0_usb0);
usb2_device_selection_in_fpga();
}
@@ -1950,19 +1950,19 @@
/* USB1.1 Device Selection */
if (ppc440ep_core_selection[USB1_DEVICE] == CORE_SELECTED)
{
- mfsdr(sdr_usb0, sdr0_usb0);
+ mfsdr(SDR0_USB0, sdr0_usb0);
sdr0_usb0 = sdr0_usb0 &~SDR0_USB0_USB_DEVSEL_MASK;
sdr0_usb0 = sdr0_usb0 | SDR0_USB0_USB11D_DEVSEL;
- mtsdr(sdr_usb0, sdr0_usb0);
+ mtsdr(SDR0_USB0, sdr0_usb0);
}
/* USB1.1 Host Selection */
if (ppc440ep_core_selection[USB1_HOST] == CORE_SELECTED)
{
- mfsdr(sdr_usb0, sdr0_usb0);
+ mfsdr(SDR0_USB0, sdr0_usb0);
sdr0_usb0 = sdr0_usb0 &~SDR0_USB0_LEEN_MASK;
sdr0_usb0 = sdr0_usb0 | SDR0_USB0_LEEN_ENABLE;
- mtsdr(sdr_usb0, sdr0_usb0);
+ mtsdr(SDR0_USB0, sdr0_usb0);
}
/* NAND Flash Selection */
@@ -1971,14 +1971,14 @@
update_ndfc_ios(gpio_tab);
#if !(defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL))
- mtsdr(sdr_cust0, SDR0_CUST0_MUX_NDFC_SEL |
+ mtsdr(SDR0_CUST0, SDR0_CUST0_MUX_NDFC_SEL |
SDR0_CUST0_NDFC_ENABLE |
SDR0_CUST0_NDFC_BW_8_BIT |
SDR0_CUST0_NDFC_ARE_MASK |
SDR0_CUST0_CHIPSELGAT_EN1 |
SDR0_CUST0_CHIPSELGAT_EN2);
#else
- mtsdr(sdr_cust0, SDR0_CUST0_MUX_NDFC_SEL |
+ mtsdr(SDR0_CUST0, SDR0_CUST0_MUX_NDFC_SEL |
SDR0_CUST0_NDFC_ENABLE |
SDR0_CUST0_NDFC_BW_8_BIT |
SDR0_CUST0_NDFC_ARE_MASK |
@@ -1991,16 +1991,16 @@
else
{
/* Set Mux on EMAC */
- mtsdr(sdr_cust0, SDR0_CUST0_MUX_EMAC_SEL);
+ mtsdr(SDR0_CUST0, SDR0_CUST0_MUX_EMAC_SEL);
}
/* MII Selection */
if (ppc440ep_core_selection[MII_SEL] == CORE_SELECTED)
{
update_zii_ios(gpio_tab);
- mfsdr(sdr_mfr, sdr0_mfr);
+ mfsdr(SDR0_MFR, sdr0_mfr);
sdr0_mfr = (sdr0_mfr & ~SDR0_MFR_ZMII_MODE_MASK) | SDR0_MFR_ZMII_MODE_MII;
- mtsdr(sdr_mfr, sdr0_mfr);
+ mtsdr(SDR0_MFR, sdr0_mfr);
set_phy_configuration_through_fpga(ZMII_CONFIGURATION_IS_MII);
}
@@ -2009,9 +2009,9 @@
if (ppc440ep_core_selection[RMII_SEL] == CORE_SELECTED)
{
update_zii_ios(gpio_tab);
- mfsdr(sdr_mfr, sdr0_mfr);
+ mfsdr(SDR0_MFR, sdr0_mfr);
sdr0_mfr = (sdr0_mfr & ~SDR0_MFR_ZMII_MODE_MASK) | SDR0_MFR_ZMII_MODE_RMII_10M;
- mtsdr(sdr_mfr, sdr0_mfr);
+ mtsdr(SDR0_MFR, sdr0_mfr);
set_phy_configuration_through_fpga(ZMII_CONFIGURATION_IS_RMII);
}
@@ -2020,9 +2020,9 @@
if (ppc440ep_core_selection[SMII_SEL] == CORE_SELECTED)
{
update_zii_ios(gpio_tab);
- mfsdr(sdr_mfr, sdr0_mfr);
+ mfsdr(SDR0_MFR, sdr0_mfr);
sdr0_mfr = (sdr0_mfr & ~SDR0_MFR_ZMII_MODE_MASK) | SDR0_MFR_ZMII_MODE_SMII;
- mtsdr(sdr_mfr, sdr0_mfr);
+ mtsdr(SDR0_MFR, sdr0_mfr);
set_phy_configuration_through_fpga(ZMII_CONFIGURATION_IS_SMII);
}
@@ -2071,13 +2071,13 @@
/* Packet Reject Function Enable */
if (ppc440ep_core_selection[PACKET_REJ_FUNC_EN] == CORE_SELECTED)
{
- mfsdr(sdr_mfr, sdr0_mfr);
+ mfsdr(SDR0_MFR, sdr0_mfr);
sdr0_mfr = (sdr0_mfr & ~SDR0_MFR_PKT_REJ_MASK) | SDR0_MFR_PKT_REJ_EN;;
- mtsdr(sdr_mfr, sdr0_mfr);
+ mtsdr(SDR0_MFR, sdr0_mfr);
}
/* Perform effective access to hardware */
- mtsdr(sdr_pfc1, sdr0_pfc1);
+ mtsdr(SDR0_PFC1, sdr0_pfc1);
set_chip_gpio_configuration(GPIO0, gpio_tab);
set_chip_gpio_configuration(GPIO1, gpio_tab);
diff --git a/board/amcc/bamboo/flash.c b/board/amcc/bamboo/flash.c
index 001348a..7bf877d 100644
--- a/board/amcc/bamboo/flash.c
+++ b/board/amcc/bamboo/flash.c
@@ -94,7 +94,7 @@
* Boot Settings in IIC EEprom address 0xA8 or 0xA4
* Read Serial Device Strap Register1 in PPC440EP
*/
- mfsdr(sdr_sdstp1, val);
+ mfsdr(SDR0_SDSTP1, val);
boot_selection = val & SDR0_SDSTP1_BOOT_SEL_MASK;
ebc_boot_size = val & SDR0_SDSTP1_EBC_ROM_BS_MASK;
diff --git a/board/amcc/bubinga/bubinga.c b/board/amcc/bubinga/bubinga.c
index 74a2a1c..d0aebec 100644
--- a/board/amcc/bubinga/bubinga.c
+++ b/board/amcc/bubinga/bubinga.c
@@ -41,9 +41,9 @@
* and enable the internal PCI arbiter if selected
*/
if (in_8((void *)FPGA_REG1) & FPGA_REG1_PCI_INT_ARB)
- mtdcr(cpc0_pci, CPC0_PCI_HOST_CFG_EN | CPC0_PCI_ARBIT_EN);
+ mtdcr(CPC0_PCI, CPC0_PCI_HOST_CFG_EN | CPC0_PCI_ARBIT_EN);
else
- mtdcr(cpc0_pci, CPC0_PCI_HOST_CFG_EN);
+ mtdcr(CPC0_PCI, CPC0_PCI_HOST_CFG_EN);
return 0;
}
diff --git a/board/amcc/bubinga/flash.c b/board/amcc/bubinga/flash.c
index a10babb..baf89d5 100644
--- a/board/amcc/bubinga/flash.c
+++ b/board/amcc/bubinga/flash.c
@@ -106,25 +106,25 @@
/* Re-do sizing to get full correct info */
if (size_b1) {
- mtdcr(ebccfga, pb0cr);
- pbcr = mfdcr(ebccfgd);
- mtdcr(ebccfga, pb0cr);
+ mtdcr(EBC0_CFGADDR, PB0CR);
+ pbcr = mfdcr(EBC0_CFGDATA);
+ mtdcr(EBC0_CFGADDR, PB0CR);
base_b1 = -size_b1;
pbcr = (pbcr & 0x0001ffff) | base_b1 |
(((size_b1 / 1024 / 1024) - 1) << 17);
- mtdcr(ebccfgd, pbcr);
- /* printf("pb1cr = %x\n", pbcr); */
+ mtdcr(EBC0_CFGDATA, pbcr);
+ /* printf("PB1CR = %x\n", pbcr); */
}
if (size_b0) {
- mtdcr(ebccfga, pb1cr);
- pbcr = mfdcr(ebccfgd);
- mtdcr(ebccfga, pb1cr);
+ mtdcr(EBC0_CFGADDR, PB1CR);
+ pbcr = mfdcr(EBC0_CFGDATA);
+ mtdcr(EBC0_CFGADDR, PB1CR);
base_b0 = base_b1 - size_b0;
pbcr = (pbcr & 0x0001ffff) | base_b0 |
(((size_b0 / 1024 / 1024) - 1) << 17);
- mtdcr(ebccfgd, pbcr);
- /* printf("pb0cr = %x\n", pbcr); */
+ mtdcr(EBC0_CFGDATA, pbcr);
+ /* printf("PB0CR = %x\n", pbcr); */
}
size_b0 = flash_get_size((vu_long *) base_b0, &flash_info[0]);
diff --git a/board/amcc/canyonlands/canyonlands.c b/board/amcc/canyonlands/canyonlands.c
index 710a0af..3a03f30 100644
--- a/board/amcc/canyonlands/canyonlands.c
+++ b/board/amcc/canyonlands/canyonlands.c
@@ -475,9 +475,9 @@
/* Remap the NOR FLASH to 0xcc00.0000 ... 0xcfff.ffff */
#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
- mtebc(pb3cr, CONFIG_SYS_FLASH_BASE_PHYS_L | 0xda000);
+ mtebc(PB3CR, CONFIG_SYS_FLASH_BASE_PHYS_L | 0xda000);
#else
- mtebc(pb0cr, CONFIG_SYS_FLASH_BASE_PHYS_L | 0xda000);
+ mtebc(PB0CR, CONFIG_SYS_FLASH_BASE_PHYS_L | 0xda000);
#endif
/* Remove TLB entry of boot EBC mapping */
diff --git a/board/amcc/ebony/ebony.c b/board/amcc/ebony/ebony.c
index ad09e62..2439b03 100644
--- a/board/amcc/ebony/ebony.c
+++ b/board/amcc/ebony/ebony.c
@@ -41,30 +41,30 @@
/*--------------------------------------------------------------------
* Setup the external bus controller/chip selects
*-------------------------------------------------------------------*/
- mtdcr(ebccfga, xbcfg);
- reg = mfdcr(ebccfgd);
- mtdcr(ebccfgd, reg | 0x04000000); /* Set ATC */
+ mtdcr(EBC0_CFGADDR, EBC0_CFG);
+ reg = mfdcr(EBC0_CFGDATA);
+ mtdcr(EBC0_CFGDATA, reg | 0x04000000); /* Set ATC */
- mtebc(pb1ap, 0x02815480); /* NVRAM/RTC */
- mtebc(pb1cr, 0x48018000); /* BA=0x480 1MB R/W 8-bit */
- mtebc(pb7ap, 0x01015280); /* FPGA registers */
- mtebc(pb7cr, 0x48318000); /* BA=0x483 1MB R/W 8-bit */
+ mtebc(PB1AP, 0x02815480); /* NVRAM/RTC */
+ mtebc(PB1CR, 0x48018000); /* BA=0x480 1MB R/W 8-bit */
+ mtebc(PB7AP, 0x01015280); /* FPGA registers */
+ mtebc(PB7CR, 0x48318000); /* BA=0x483 1MB R/W 8-bit */
/* read FPGA_REG0 and set the bus controller */
status = *fpga_base;
if ((status & BOOT_SMALL_FLASH) && !(status & FLASH_ONBD_N)) {
- mtebc(pb0ap, 0x9b015480); /* FLASH/SRAM */
- mtebc(pb0cr, 0xfff18000); /* BAS=0xfff 1MB R/W 8-bit */
- mtebc(pb2ap, 0x9b015480); /* 4MB FLASH */
- mtebc(pb2cr, 0xff858000); /* BAS=0xff8 4MB R/W 8-bit */
+ mtebc(PB0AP, 0x9b015480); /* FLASH/SRAM */
+ mtebc(PB0CR, 0xfff18000); /* BAS=0xfff 1MB R/W 8-bit */
+ mtebc(PB2AP, 0x9b015480); /* 4MB FLASH */
+ mtebc(PB2CR, 0xff858000); /* BAS=0xff8 4MB R/W 8-bit */
} else {
- mtebc(pb0ap, 0x9b015480); /* 4MB FLASH */
- mtebc(pb0cr, 0xffc58000); /* BAS=0xffc 4MB R/W 8-bit */
+ mtebc(PB0AP, 0x9b015480); /* 4MB FLASH */
+ mtebc(PB0CR, 0xffc58000); /* BAS=0xffc 4MB R/W 8-bit */
/* set CS2 if FLASH_ONBD_N == 0 */
if (!(status & FLASH_ONBD_N)) {
- mtebc(pb2ap, 0x9b015480); /* FLASH/SRAM */
- mtebc(pb2cr, 0xff818000); /* BAS=0xff8 4MB R/W 8-bit */
+ mtebc(PB2AP, 0x9b015480); /* FLASH/SRAM */
+ mtebc(PB2CR, 0xff818000); /* BAS=0xff8 4MB R/W 8-bit */
}
}
@@ -186,7 +186,7 @@
* The ebony board is always configured as the host & requires the
* PCI arbiter to be enabled.
*--------------------------------------------------------------------------*/
- strap = mfdcr(cpc0_strp1);
+ strap = mfdcr(CPC0_STRP1);
if ((strap & 0x00100000) == 0) {
printf("PCI: CPC0_STRP1[PAE] not set.\n");
return 0;
diff --git a/board/amcc/katmai/katmai.c b/board/amcc/katmai/katmai.c
index e078ba4..1a45056 100644
--- a/board/amcc/katmai/katmai.c
+++ b/board/amcc/katmai/katmai.c
@@ -220,9 +220,9 @@
mtdcr (uic0sr, 0x00000000); /* clear all interrupts*/
mtdcr (uic0sr, 0xffffffff); /* clear all interrupts*/
- mfsdr(sdr_mfr, mfr);
+ mfsdr(SDR0_MFR, mfr);
mfr |= SDR0_MFR_FIXD; /* Workaround for PCI/DMA */
- mtsdr(sdr_mfr, mfr);
+ mtsdr(SDR0_MFR, mfr);
mtsdr(SDR0_PFC0, CONFIG_SYS_PFC0);
@@ -280,7 +280,7 @@
* The katmai board is always configured as the host & requires the
* PCI arbiter to be enabled.
*-------------------------------------------------------------------*/
- mfsdr(sdr_sdstp1, strap);
+ mfsdr(SDR0_SDSTP1, strap);
if( (strap & SDR0_SDSTP1_PAE_MASK) == 0 ) {
printf("PCI: SDR0_STRP1[%08lX] - PCI Arbiter disabled.\n",strap);
return 0;
diff --git a/board/amcc/luan/luan.c b/board/amcc/luan/luan.c
index 7d02d90..71ad89f 100644
--- a/board/amcc/luan/luan.c
+++ b/board/amcc/luan/luan.c
@@ -42,12 +42,12 @@
{
u32 mfr;
- mtebc( pb0ap, 0x03800000 ); /* set chip selects */
- mtebc( pb0cr, 0xffc58000 ); /* ebc0_b0cr, 4MB at 0xffc00000 CS0 */
- mtebc( pb1ap, 0x03800000 );
- mtebc( pb1cr, 0xff018000 ); /* ebc0_b1cr, 1MB at 0xff000000 CS1 */
- mtebc( pb2ap, 0x03800000 );
- mtebc( pb2cr, 0xff838000 ); /* ebc0_b2cr, 2MB at 0xff800000 CS2 */
+ mtebc( PB0AP, 0x03800000 ); /* set chip selects */
+ mtebc( PB0CR, 0xffc58000 ); /* ebc0_b0cr, 4MB at 0xffc00000 CS0 */
+ mtebc( PB1AP, 0x03800000 );
+ mtebc( PB1CR, 0xff018000 ); /* ebc0_b1cr, 1MB at 0xff000000 CS1 */
+ mtebc( PB2AP, 0x03800000 );
+ mtebc( PB2CR, 0xff838000 ); /* ebc0_b2cr, 2MB at 0xff800000 CS2 */
mtdcr( uic1sr, 0xffffffff ); /* Clear all interrupts */
mtdcr( uic1er, 0x00000000 ); /* disable all interrupts */
@@ -67,9 +67,9 @@
mtdcr( uic0sr, 0x00000000 ); /* clear all interrupts */
mtdcr( uic0sr, 0xffffffff );
- mfsdr(sdr_mfr, mfr);
+ mfsdr(SDR0_MFR, mfr);
mfr |= SDR0_MFR_FIXD; /* Workaround for PCI/DMA */
- mtsdr(sdr_mfr, mfr);
+ mtsdr(SDR0_MFR, mfr);
return 0;
}
@@ -147,7 +147,7 @@
* The luan board is always configured as the host & requires the
* PCI arbiter to be enabled.
*--------------------------------------------------------------------------*/
- mfsdr(sdr_sdstp1, strap);
+ mfsdr(SDR0_SDSTP1, strap);
if( (strap & SDR0_SDSTP1_PAE_MASK) == 0 ) {
printf("PCI: SDR0_STRP1[%08lX] - PCI Arbiter disabled.\n",strap);
diff --git a/board/amcc/ocotea/ocotea.c b/board/amcc/ocotea/ocotea.c
index fe45408..5e32e8a 100644
--- a/board/amcc/ocotea/ocotea.c
+++ b/board/amcc/ocotea/ocotea.c
@@ -54,7 +54,7 @@
/*-------------------------------------------------------------------------+
| Initialize EBC CONFIG
+-------------------------------------------------------------------------*/
- mtebc(xbcfg, EBC_CFG_LE_UNLOCK |
+ mtebc(EBC0_CFG, EBC_CFG_LE_UNLOCK |
EBC_CFG_PTD_ENABLE | EBC_CFG_RTC_64PERCLK |
EBC_CFG_ATC_PREVIOUS | EBC_CFG_DTC_PREVIOUS |
EBC_CFG_CTC_PREVIOUS | EBC_CFG_EMC_NONDEFAULT |
@@ -63,14 +63,14 @@
/*-------------------------------------------------------------------------+
| FPGA. Initialize bank 7 with default values.
+-------------------------------------------------------------------------*/
- mtebc(pb7ap, EBC_BXAP_BME_DISABLED|EBC_BXAP_TWT_ENCODE(7)|
+ mtebc(PB7AP, EBC_BXAP_BME_DISABLED|EBC_BXAP_TWT_ENCODE(7)|
EBC_BXAP_BCE_DISABLE|
EBC_BXAP_CSN_ENCODE(1)|EBC_BXAP_OEN_ENCODE(1)|
EBC_BXAP_WBN_ENCODE(1)|EBC_BXAP_WBF_ENCODE(1)|
EBC_BXAP_TH_ENCODE(1)|EBC_BXAP_RE_DISABLED|
EBC_BXAP_BEM_WRITEONLY|
EBC_BXAP_PEN_DISABLED);
- mtebc(pb7cr, EBC_BXCR_BAS_ENCODE(0x48300000)|
+ mtebc(PB7CR, EBC_BXCR_BAS_ENCODE(0x48300000)|
EBC_BXCR_BS_1MB|EBC_BXCR_BU_RW|EBC_BXCR_BW_8BIT);
/* read FPGA base register FPGA_REG0 */
@@ -95,53 +95,53 @@
/*-------------------------------------------------------------------------+
| 1 MB FLASH / 1 MB SRAM. Initialize bank 0 with default values.
+-------------------------------------------------------------------------*/
- mtebc(pb0ap, EBC_BXAP_BME_DISABLED|EBC_BXAP_TWT_ENCODE(cs0_twt)|
+ mtebc(PB0AP, EBC_BXAP_BME_DISABLED|EBC_BXAP_TWT_ENCODE(cs0_twt)|
EBC_BXAP_BCE_DISABLE|
EBC_BXAP_CSN_ENCODE(1)|EBC_BXAP_OEN_ENCODE(1)|
EBC_BXAP_WBN_ENCODE(1)|EBC_BXAP_WBF_ENCODE(1)|
EBC_BXAP_TH_ENCODE(1)|EBC_BXAP_RE_DISABLED|
EBC_BXAP_BEM_WRITEONLY|
EBC_BXAP_PEN_DISABLED);
- mtebc(pb0cr, EBC_BXCR_BAS_ENCODE(cs0_base)|
+ mtebc(PB0CR, EBC_BXCR_BAS_ENCODE(cs0_base)|
cs0_size|EBC_BXCR_BU_RW|EBC_BXCR_BW_8BIT);
/*-------------------------------------------------------------------------+
| 8KB NVRAM/RTC. Initialize bank 1 with default values.
+-------------------------------------------------------------------------*/
- mtebc(pb1ap, EBC_BXAP_BME_DISABLED|EBC_BXAP_TWT_ENCODE(10)|
+ mtebc(PB1AP, EBC_BXAP_BME_DISABLED|EBC_BXAP_TWT_ENCODE(10)|
EBC_BXAP_BCE_DISABLE|
EBC_BXAP_CSN_ENCODE(1)|EBC_BXAP_OEN_ENCODE(1)|
EBC_BXAP_WBN_ENCODE(1)|EBC_BXAP_WBF_ENCODE(1)|
EBC_BXAP_TH_ENCODE(1)|EBC_BXAP_RE_DISABLED|
EBC_BXAP_BEM_WRITEONLY|
EBC_BXAP_PEN_DISABLED);
- mtebc(pb1cr, EBC_BXCR_BAS_ENCODE(0x48000000)|
+ mtebc(PB1CR, EBC_BXCR_BAS_ENCODE(0x48000000)|
EBC_BXCR_BS_1MB|EBC_BXCR_BU_RW|EBC_BXCR_BW_8BIT);
/*-------------------------------------------------------------------------+
| 4 MB FLASH. Initialize bank 2 with default values.
+-------------------------------------------------------------------------*/
- mtebc(pb2ap, EBC_BXAP_BME_DISABLED|EBC_BXAP_TWT_ENCODE(cs2_twt)|
+ mtebc(PB2AP, EBC_BXAP_BME_DISABLED|EBC_BXAP_TWT_ENCODE(cs2_twt)|
EBC_BXAP_BCE_DISABLE|
EBC_BXAP_CSN_ENCODE(1)|EBC_BXAP_OEN_ENCODE(1)|
EBC_BXAP_WBN_ENCODE(1)|EBC_BXAP_WBF_ENCODE(1)|
EBC_BXAP_TH_ENCODE(1)|EBC_BXAP_RE_DISABLED|
EBC_BXAP_BEM_WRITEONLY|
EBC_BXAP_PEN_DISABLED);
- mtebc(pb2cr, EBC_BXCR_BAS_ENCODE(cs2_base)|
+ mtebc(PB2CR, EBC_BXCR_BAS_ENCODE(cs2_base)|
cs2_size|EBC_BXCR_BU_RW|EBC_BXCR_BW_8BIT);
/*-------------------------------------------------------------------------+
| FPGA. Initialize bank 7 with default values.
+-------------------------------------------------------------------------*/
- mtebc(pb7ap, EBC_BXAP_BME_DISABLED|EBC_BXAP_TWT_ENCODE(7)|
+ mtebc(PB7AP, EBC_BXAP_BME_DISABLED|EBC_BXAP_TWT_ENCODE(7)|
EBC_BXAP_BCE_DISABLE|
EBC_BXAP_CSN_ENCODE(1)|EBC_BXAP_OEN_ENCODE(1)|
EBC_BXAP_WBN_ENCODE(1)|EBC_BXAP_WBF_ENCODE(1)|
EBC_BXAP_TH_ENCODE(1)|EBC_BXAP_RE_DISABLED|
EBC_BXAP_BEM_WRITEONLY|
EBC_BXAP_PEN_DISABLED);
- mtebc(pb7cr, EBC_BXCR_BAS_ENCODE(0x48300000)|
+ mtebc(PB7CR, EBC_BXCR_BAS_ENCODE(0x48300000)|
EBC_BXCR_BS_1MB|EBC_BXCR_BU_RW|EBC_BXCR_BW_8BIT);
/*--------------------------------------------------------------------
@@ -189,9 +189,9 @@
mtdcr (uic0pr, 0xfc000000); /* */
mtdcr (uic0tr, 0x00000000); /* */
mtdcr (uic0vr, 0x00000001); /* */
- mfsdr (sdr_mfr, mfr);
+ mfsdr (SDR0_MFR, mfr);
mfr &= ~SDR0_MFR_ECS_MASK;
-/* mtsdr(sdr_mfr, mfr); */
+/* mtsdr(SDR0_MFR, mfr); */
fpga_init();
return 0;
@@ -297,7 +297,7 @@
* The ocotea board is always configured as the host & requires the
* PCI arbiter to be enabled.
*--------------------------------------------------------------------------*/
- mfsdr(sdr_sdstp1, strap);
+ mfsdr(SDR0_SDSTP1, strap);
if( (strap & SDR0_SDSTP1_PAE_MASK) == 0 ){
printf("PCI: SDR0_STRP1[%08lX] - PCI Arbiter disabled.\n",strap);
return 0;
@@ -379,8 +379,8 @@
unsigned long sdr0_cust0;
unsigned long pvr;
- mfsdr (sdr_pfc0, sdr0_pfc0);
- mfsdr (sdr_pfc1, sdr0_pfc1);
+ mfsdr (SDR0_PFC0, sdr0_pfc0);
+ mfsdr (SDR0_PFC1, sdr0_pfc1);
group = SDR0_PFC1_EPS_DECODE(sdr0_pfc1);
pvr = get_pvr ();
@@ -390,8 +390,8 @@
sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_CTEMS_MASK) | SDR0_PFC1_CTEMS_EMS;
out8(FPGA_REG2, (in8(FPGA_REG2) & ~FPGA_REG2_EXT_INTFACE_MASK) |
FPGA_REG2_EXT_INTFACE_ENABLE);
- mtsdr (sdr_pfc0, sdr0_pfc0);
- mtsdr (sdr_pfc1, sdr0_pfc1);
+ mtsdr (SDR0_PFC0, sdr0_pfc0);
+ mtsdr (SDR0_PFC1, sdr0_pfc1);
} else {
sdr0_pfc0 = (sdr0_pfc0 & ~SDR0_PFC0_TRE_MASK) | SDR0_PFC0_TRE_ENABLE;
switch (group)
@@ -403,8 +403,8 @@
out8(FPGA_REG2, (in8(FPGA_REG2) & ~FPGA_REG2_EXT_INTFACE_MASK) |
FPGA_REG2_EXT_INTFACE_ENABLE);
sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_CTEMS_MASK) | SDR0_PFC1_CTEMS_EMS;
- mtsdr (sdr_pfc0, sdr0_pfc0);
- mtsdr (sdr_pfc1, sdr0_pfc1);
+ mtsdr (SDR0_PFC0, sdr0_pfc0);
+ mtsdr (SDR0_PFC1, sdr0_pfc1);
break;
case 3:
case 4:
@@ -412,8 +412,8 @@
case 6:
/* CPU trace B - Over EBMI */
sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_CTEMS_MASK) | SDR0_PFC1_CTEMS_CPUTRACE;
- mtsdr (sdr_pfc0, sdr0_pfc0);
- mtsdr (sdr_pfc1, sdr0_pfc1);
+ mtsdr (SDR0_PFC0, sdr0_pfc0);
+ mtsdr (SDR0_PFC1, sdr0_pfc1);
out8(FPGA_REG2, (in8(FPGA_REG2) & ~FPGA_REG2_EXT_INTFACE_MASK) |
FPGA_REG2_EXT_INTFACE_DISABLE);
break;
@@ -421,8 +421,8 @@
}
/* Initialize the ethernet specific functions in the fpga */
- mfsdr(sdr_pfc1, sdr0_pfc1);
- mfsdr(sdr_cust0, sdr0_cust0);
+ mfsdr(SDR0_PFC1, sdr0_pfc1);
+ mfsdr(SDR0_CUST0, sdr0_cust0);
if ( (SDR0_PFC1_EPS_DECODE(sdr0_pfc1) == 4) &&
((SDR0_CUST0_RGMII2_DECODE(sdr0_cust0) == RGMII_FER_GMII) ||
(SDR0_CUST0_RGMII2_DECODE(sdr0_cust0) == RGMII_FER_TBI)))
diff --git a/board/amcc/redwood/redwood.c b/board/amcc/redwood/redwood.c
index 37a0c31..49078eb 100644
--- a/board/amcc/redwood/redwood.c
+++ b/board/amcc/redwood/redwood.c
@@ -220,7 +220,7 @@
* default value :
* 0x07C00000 - 0 0 000 1 1 1 1 1 0000 0 00000 000000000000
*/
- mtebc(xbcfg, EBC_CFG_LE_UNLOCK |
+ mtebc(EBC0_CFG, EBC_CFG_LE_UNLOCK |
EBC_CFG_PTD_ENABLE |
EBC_CFG_RTC_16PERCLK |
EBC_CFG_ATC_PREVIOUS |
@@ -237,8 +237,8 @@
* since some board registers values may be needed to determine the
* boot type
*/
- mtebc(pb1ap, EBC_BXAP_FPGA);
- mtebc(pb1cr, EBC_BXCR_FPGA_CS3);
+ mtebc(PB1AP, EBC_BXAP_FPGA);
+ mtebc(PB1CR, EBC_BXCR_FPGA_CS3);
}
@@ -399,12 +399,12 @@
break;
}
- mtebc(pb0ap, ebc0_cs0_bxap_value);
- mtebc(pb0cr, ebc0_cs0_bxcr_value);
- mtebc(pb1ap, ebc0_cs1_bxap_value);
- mtebc(pb1cr, ebc0_cs1_bxcr_value);
- mtebc(pb2ap, ebc0_cs2_bxap_value);
- mtebc(pb2cr, ebc0_cs2_bxcr_value);
+ mtebc(PB0AP, ebc0_cs0_bxap_value);
+ mtebc(PB0CR, ebc0_cs0_bxcr_value);
+ mtebc(PB1AP, ebc0_cs1_bxap_value);
+ mtebc(PB1CR, ebc0_cs1_bxcr_value);
+ mtebc(PB2AP, ebc0_cs2_bxap_value);
+ mtebc(PB2CR, ebc0_cs2_bxcr_value);
}
static void early_init_UIC(void)
diff --git a/board/amcc/sequoia/sequoia.c b/board/amcc/sequoia/sequoia.c
index 246ad94..5913455 100644
--- a/board/amcc/sequoia/sequoia.c
+++ b/board/amcc/sequoia/sequoia.c
@@ -46,8 +46,8 @@
u32 sdr0_pfc1, sdr0_pfc2;
u32 reg;
- mtdcr(ebccfga, xbcfg);
- mtdcr(ebccfgd, 0xb8400000);
+ mtdcr(EBC0_CFGADDR, EBC0_CFG);
+ mtdcr(EBC0_CFGDATA, 0xb8400000);
/*
* Setup the interrupt controller polarities, triggers, etc.
@@ -107,8 +107,8 @@
mtsdr(SDR0_PFC1, sdr0_pfc1);
/* PCI arbiter enabled */
- mfsdr(sdr_pci0, reg);
- mtsdr(sdr_pci0, 0x80000000 | reg);
+ mfsdr(SDR0_PCI0, reg);
+ mtsdr(SDR0_PCI0, 0x80000000 | reg);
/* setup NAND FLASH */
mfsdr(SDR0_CUST0, sdr0_cust0);
@@ -144,19 +144,19 @@
gd->bd->bi_flashoffset = 0;
#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
- mtdcr(ebccfga, pb3cr);
+ mtdcr(EBC0_CFGADDR, PB3CR);
#else
- mtdcr(ebccfga, pb0cr);
+ mtdcr(EBC0_CFGADDR, PB0CR);
#endif
- pbcr = mfdcr(ebccfgd);
+ pbcr = mfdcr(EBC0_CFGDATA);
size_val = ffs(gd->bd->bi_flashsize) - 21;
pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
- mtdcr(ebccfga, pb3cr);
+ mtdcr(EBC0_CFGADDR, PB3CR);
#else
- mtdcr(ebccfga, pb0cr);
+ mtdcr(EBC0_CFGADDR, PB0CR);
#endif
- mtdcr(ebccfgd, pbcr);
+ mtdcr(EBC0_CFGDATA, pbcr);
/*
* Re-check to get correct base address
@@ -309,8 +309,8 @@
* This fix will make the MAL burst disabling patch for the Linux
* EMAC driver obsolete.
*/
- reg = mfdcr(plb4_acr) & ~PLB4_ACR_WRP;
- mtdcr(plb4_acr, reg);
+ reg = mfdcr(PLB4_ACR) & ~PLB4_ACR_WRP;
+ mtdcr(PLB4_ACR, reg);
return 0;
}
@@ -370,35 +370,35 @@
* Set priority for all PLB3 devices to 0.
* Set PLB3 arbiter to fair mode.
*/
- mfsdr(sdr_amp1, addr);
- mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(plb3_acr);
- mtdcr(plb3_acr, addr | 0x80000000);
+ mfsdr(SD0_AMP1, addr);
+ mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
+ addr = mfdcr(PLB3_ACR);
+ mtdcr(PLB3_ACR, addr | 0x80000000);
/*
* Set priority for all PLB4 devices to 0.
*/
- mfsdr(sdr_amp0, addr);
- mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(plb4_acr) | 0xa0000000; /* Was 0x8---- */
- mtdcr(plb4_acr, addr);
+ mfsdr(SD0_AMP0, addr);
+ mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
+ addr = mfdcr(PLB4_ACR) | 0xa0000000; /* Was 0x8---- */
+ mtdcr(PLB4_ACR, addr);
/*
* Set Nebula PLB4 arbiter to fair mode.
*/
/* Segment0 */
- addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair;
- addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled;
- addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep;
- addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep;
- mtdcr(plb0_acr, addr);
+ addr = (mfdcr(PLB0_ACR) & ~PLB0_ACR_PPM_MASK) | PLB0_ACR_PPM_FAIR;
+ addr = (addr & ~PLB0_ACR_HBU_MASK) | PLB0_ACR_HBU_ENABLED;
+ addr = (addr & ~PLB0_ACR_RDP_MASK) | PLB0_ACR_RDP_4DEEP;
+ addr = (addr & ~PLB0_ACR_WRP_MASK) | PLB0_ACR_WRP_2DEEP;
+ mtdcr(PLB0_ACR, addr);
/* Segment1 */
- addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair;
- addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled;
- addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep;
- addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep;
- mtdcr(plb1_acr, addr);
+ addr = (mfdcr(PLB1_ACR) & ~PLB1_ACR_PPM_MASK) | PLB1_ACR_PPM_FAIR;
+ addr = (addr & ~PLB1_ACR_HBU_MASK) | PLB1_ACR_HBU_ENABLED;
+ addr = (addr & ~PLB1_ACR_RDP_MASK) | PLB1_ACR_RDP_4DEEP;
+ addr = (addr & ~PLB1_ACR_WRP_MASK) | PLB1_ACR_WRP_2DEEP;
+ mtdcr(PLB1_ACR, addr);
#ifdef CONFIG_PCI_PNP
hose->fixup_irq = sequoia_pci_fixup_irq;
diff --git a/board/amcc/taihu/taihu.c b/board/amcc/taihu/taihu.c
index d8806ac..4e5796e 100644
--- a/board/amcc/taihu/taihu.c
+++ b/board/amcc/taihu/taihu.c
@@ -48,14 +48,14 @@
mtdcr(uicsr, 0xFFFFFFFF); /* clear all ints */
mtdcr(uicvcr, 0x00000001); /* set vect base=0,INT0 highest priority */
- mtebc(pb3ap, CONFIG_SYS_EBC_PB3AP); /* memory bank 3 (CPLD_LCM) initialization */
- mtebc(pb3cr, CONFIG_SYS_EBC_PB3CR);
+ mtebc(PB3AP, CONFIG_SYS_EBC_PB3AP); /* memory bank 3 (CPLD_LCM) initialization */
+ mtebc(PB3CR, CONFIG_SYS_EBC_PB3CR);
/*
* Configure CPC0_PCI to enable PerWE as output
* and enable the internal PCI arbiter
*/
- mtdcr(cpc0_pci, CPC0_PCI_SPE | CPC0_PCI_HOST_CFG_EN | CPC0_PCI_ARBIT_EN);
+ mtdcr(CPC0_PCI, CPC0_PCI_SPE | CPC0_PCI_HOST_CFG_EN | CPC0_PCI_ARBIT_EN);
return 0;
}
diff --git a/board/amcc/taishan/showinfo.c b/board/amcc/taishan/showinfo.c
index 2a78a22..e4e441b 100644
--- a/board/amcc/taishan/showinfo.c
+++ b/board/amcc/taishan/showinfo.c
@@ -33,60 +33,60 @@
/* read clock regsiter */
printf("===== Display reset and initialize register Start =========\n");
- mfcpr(clk_pllc,reg);
+ mfcpr(CPR0_PLLC,reg);
printf("cpr_pllc = %#010lx\n",reg);
- mfcpr(clk_plld,reg);
+ mfcpr(CPR0_PLLD,reg);
printf("cpr_plld = %#010lx\n",reg);
- mfcpr(clk_primad,reg);
+ mfcpr(CPR0_PRIMAD,reg);
printf("cpr_primad = %#010lx\n",reg);
- mfcpr(clk_primbd,reg);
+ mfcpr(CPR0_PRIMBD,reg);
printf("cpr_primbd = %#010lx\n",reg);
- mfcpr(clk_opbd,reg);
+ mfcpr(CPR0_OPBD,reg);
printf("cpr_opbd = %#010lx\n",reg);
- mfcpr(clk_perd,reg);
+ mfcpr(CPR0_PERD,reg);
printf("cpr_perd = %#010lx\n",reg);
- mfcpr(clk_mald,reg);
+ mfcpr(CPR0_MALD,reg);
printf("cpr_mald = %#010lx\n",reg);
/* read sdr register */
- mfsdr(sdr_ebc,reg);
- printf("sdr_ebc = %#010lx\n",reg);
+ mfsdr(SDR0_EBC,reg);
+ printf("SDR0_EBC = %#010lx\n",reg);
- mfsdr(sdr_cp440,reg);
- printf("sdr_cp440 = %#010lx\n",reg);
+ mfsdr(SDR0_CP440,reg);
+ printf("SDR0_CP440 = %#010lx\n",reg);
- mfsdr(sdr_xcr,reg);
- printf("sdr_xcr = %#010lx\n",reg);
+ mfsdr(SDR0_XCR,reg);
+ printf("SDR0_XCR = %#010lx\n",reg);
- mfsdr(sdr_xpllc,reg);
- printf("sdr_xpllc = %#010lx\n",reg);
+ mfsdr(SDR0_XPLLC,reg);
+ printf("SDR0_XPLLC = %#010lx\n",reg);
- mfsdr(sdr_xplld,reg);
- printf("sdr_xplld = %#010lx\n",reg);
+ mfsdr(SDR0_XPLLD,reg);
+ printf("SDR0_XPLLD = %#010lx\n",reg);
- mfsdr(sdr_pfc0,reg);
- printf("sdr_pfc0 = %#010lx\n",reg);
+ mfsdr(SDR0_PFC0,reg);
+ printf("SDR0_PFC0 = %#010lx\n",reg);
- mfsdr(sdr_pfc1,reg);
- printf("sdr_pfc1 = %#010lx\n",reg);
+ mfsdr(SDR0_PFC1,reg);
+ printf("SDR0_PFC1 = %#010lx\n",reg);
- mfsdr(sdr_cust0,reg);
- printf("sdr_cust0 = %#010lx\n",reg);
+ mfsdr(SDR0_CUST0,reg);
+ printf("SDR0_CUST0 = %#010lx\n",reg);
- mfsdr(sdr_cust1,reg);
- printf("sdr_cust1 = %#010lx\n",reg);
+ mfsdr(SDR0_CUST1,reg);
+ printf("SDR0_CUST1 = %#010lx\n",reg);
- mfsdr(sdr_uart0,reg);
- printf("sdr_uart0 = %#010lx\n",reg);
+ mfsdr(SDR0_UART0,reg);
+ printf("SDR0_UART0 = %#010lx\n",reg);
- mfsdr(sdr_uart1,reg);
- printf("sdr_uart1 = %#010lx\n",reg);
+ mfsdr(SDR0_UART1,reg);
+ printf("SDR0_UART1 = %#010lx\n",reg);
printf("===== Display reset and initialize register End =========\n");
}
@@ -96,14 +96,14 @@
unsigned long reg;
printf("PCI-X chip control registers\n");
- mfsdr(sdr_xcr, reg);
- printf("sdr_xcr = %#010lx\n", reg);
+ mfsdr(SDR0_XCR, reg);
+ printf("SDR0_XCR = %#010lx\n", reg);
- mfsdr(sdr_xpllc, reg);
- printf("sdr_xpllc = %#010lx\n", reg);
+ mfsdr(SDR0_XPLLC, reg);
+ printf("SDR0_XPLLC = %#010lx\n", reg);
- mfsdr(sdr_xplld, reg);
- printf("sdr_xplld = %#010lx\n", reg);
+ mfsdr(SDR0_XPLLD, reg);
+ printf("SDR0_XPLLD = %#010lx\n", reg);
printf("PCI-X Bridge Configure registers\n");
printf("PCIX0_VENDID = %#06x\n", in16r(PCIX0_VENDID));
diff --git a/board/amcc/taishan/taishan.c b/board/amcc/taishan/taishan.c
index 53ce88c..086778a 100644
--- a/board/amcc/taishan/taishan.c
+++ b/board/amcc/taishan/taishan.c
@@ -47,7 +47,7 @@
/*-------------------------------------------------------------------------+
| Initialize EBC CONFIG
+-------------------------------------------------------------------------*/
- mtebc(xbcfg, EBC_CFG_LE_UNLOCK |
+ mtebc(EBC0_CFG, EBC_CFG_LE_UNLOCK |
EBC_CFG_PTD_ENABLE | EBC_CFG_RTC_64PERCLK |
EBC_CFG_ATC_PREVIOUS | EBC_CFG_DTC_PREVIOUS |
EBC_CFG_CTC_PREVIOUS | EBC_CFG_EMC_DEFAULT |
@@ -56,66 +56,66 @@
/*-------------------------------------------------------------------------+
| 64MB FLASH. Initialize bank 0 with default values.
+-------------------------------------------------------------------------*/
- mtebc(pb0ap, EBC_BXAP_BME_DISABLED|EBC_BXAP_TWT_ENCODE(15) |
+ mtebc(PB0AP, EBC_BXAP_BME_DISABLED|EBC_BXAP_TWT_ENCODE(15) |
EBC_BXAP_BCE_DISABLE |
EBC_BXAP_CSN_ENCODE(1) | EBC_BXAP_OEN_ENCODE(1) |
EBC_BXAP_WBN_ENCODE(1) | EBC_BXAP_WBF_ENCODE(1) |
EBC_BXAP_TH_ENCODE(3) | EBC_BXAP_RE_DISABLED |
EBC_BXAP_BEM_WRITEONLY |
EBC_BXAP_PEN_DISABLED);
- mtebc(pb0cr, EBC_BXCR_BAS_ENCODE(CONFIG_SYS_FLASH_BASE) |
+ mtebc(PB0CR, EBC_BXCR_BAS_ENCODE(CONFIG_SYS_FLASH_BASE) |
EBC_BXCR_BS_64MB | EBC_BXCR_BU_RW|EBC_BXCR_BW_32BIT);
/*-------------------------------------------------------------------------+
| FPGA. Initialize bank 1 with default values.
+-------------------------------------------------------------------------*/
- mtebc(pb1ap, EBC_BXAP_BME_DISABLED|EBC_BXAP_TWT_ENCODE(5) |
+ mtebc(PB1AP, EBC_BXAP_BME_DISABLED|EBC_BXAP_TWT_ENCODE(5) |
EBC_BXAP_BCE_DISABLE |
EBC_BXAP_CSN_ENCODE(1) | EBC_BXAP_OEN_ENCODE(1) |
EBC_BXAP_WBN_ENCODE(1) | EBC_BXAP_WBF_ENCODE(1) |
EBC_BXAP_TH_ENCODE(3) | EBC_BXAP_RE_DISABLED |
EBC_BXAP_BEM_WRITEONLY |
EBC_BXAP_PEN_DISABLED);
- mtebc(pb1cr, EBC_BXCR_BAS_ENCODE(0x41000000) |
+ mtebc(PB1CR, EBC_BXCR_BAS_ENCODE(0x41000000) |
EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_8BIT);
/*-------------------------------------------------------------------------+
| LCM. Initialize bank 2 with default values.
+-------------------------------------------------------------------------*/
- mtebc(pb2ap, EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(64) |
+ mtebc(PB2AP, EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(64) |
EBC_BXAP_BCE_DISABLE |
EBC_BXAP_CSN_ENCODE(3) | EBC_BXAP_OEN_ENCODE(3) |
EBC_BXAP_WBN_ENCODE(3) | EBC_BXAP_WBF_ENCODE(3) |
EBC_BXAP_TH_ENCODE(7) | EBC_BXAP_RE_DISABLED |
EBC_BXAP_BEM_WRITEONLY |
EBC_BXAP_PEN_DISABLED);
- mtebc(pb2cr, EBC_BXCR_BAS_ENCODE(0x42000000) |
+ mtebc(PB2CR, EBC_BXCR_BAS_ENCODE(0x42000000) |
EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW|EBC_BXCR_BW_8BIT);
/*-------------------------------------------------------------------------+
| TMP. Initialize bank 3 with default values.
+-------------------------------------------------------------------------*/
- mtebc(pb3ap, EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(128) |
+ mtebc(PB3AP, EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(128) |
EBC_BXAP_BCE_DISABLE |
EBC_BXAP_CSN_ENCODE(3) | EBC_BXAP_OEN_ENCODE(3) |
EBC_BXAP_WBN_ENCODE(3) | EBC_BXAP_WBF_ENCODE(3) |
EBC_BXAP_TH_ENCODE(7) | EBC_BXAP_RE_DISABLED |
EBC_BXAP_BEM_WRITEONLY |
EBC_BXAP_PEN_DISABLED);
- mtebc(pb3cr, EBC_BXCR_BAS_ENCODE(0x48000000) |
+ mtebc(PB3CR, EBC_BXCR_BAS_ENCODE(0x48000000) |
EBC_BXCR_BS_64MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_32BIT);
/*-------------------------------------------------------------------------+
| Connector 4~7. Initialize bank 3~ 7 with default values.
+-------------------------------------------------------------------------*/
- mtebc(pb4ap,0);
- mtebc(pb4cr,0);
- mtebc(pb5ap,0);
- mtebc(pb5cr,0);
- mtebc(pb6ap,0);
- mtebc(pb6cr,0);
- mtebc(pb7ap,0);
- mtebc(pb7cr,0);
+ mtebc(PB4AP,0);
+ mtebc(PB4CR,0);
+ mtebc(PB5AP,0);
+ mtebc(PB5CR,0);
+ mtebc(PB6AP,0);
+ mtebc(PB6CR,0);
+ mtebc(PB7AP,0);
+ mtebc(PB7CR,0);
/*--------------------------------------------------------------------
* Setup the interrupt controller polarities, triggers, etc.
@@ -164,13 +164,13 @@
mtdcr (uic0vr, 0x00000001); /* */
/* Enable two GPIO 10~11 and TraceA signal */
- mfsdr(sdr_pfc0,reg);
+ mfsdr(SDR0_PFC0,reg);
reg |= 0x00300000;
- mtsdr(sdr_pfc0,reg);
+ mtsdr(SDR0_PFC0,reg);
- mfsdr(sdr_pfc1,reg);
+ mfsdr(SDR0_PFC1,reg);
reg |= 0x00100000;
- mtsdr(sdr_pfc1,reg);
+ mtsdr(SDR0_PFC1,reg);
/* Set GPIO 10 and 11 as output */
GpioOdr = (volatile unsigned int*)(CONFIG_SYS_PERIPHERAL_BASE+0x718);
@@ -230,7 +230,7 @@
* The ocotea board is always configured as the host & requires the
* PCI arbiter to be enabled.
*--------------------------------------------------------------------------*/
- mfsdr(sdr_sdstp1, strap);
+ mfsdr(SDR0_SDSTP1, strap);
if( (strap & SDR0_SDSTP1_PAE_MASK) == 0 ){
printf("PCI: SDR0_STRP1[%08lX] - PCI Arbiter disabled.\n",strap);
return 0;
diff --git a/board/amcc/walnut/flash.c b/board/amcc/walnut/flash.c
index d363564..3dc6aab 100644
--- a/board/amcc/walnut/flash.c
+++ b/board/amcc/walnut/flash.c
@@ -102,27 +102,27 @@
/* Re-do sizing to get full correct info */
if (size_b1) {
- mtdcr(ebccfga, pb0cr);
- pbcr = mfdcr(ebccfgd);
- mtdcr(ebccfga, pb0cr);
+ mtdcr(EBC0_CFGADDR, PB0CR);
+ pbcr = mfdcr(EBC0_CFGDATA);
+ mtdcr(EBC0_CFGADDR, PB0CR);
base_b1 = -size_b1;
pbcr =
(pbcr & 0x0001ffff) | base_b1 |
(((size_b1 / 1024 / 1024) - 1) << 17);
- mtdcr(ebccfgd, pbcr);
- /* printf("pb1cr = %x\n", pbcr); */
+ mtdcr(EBC0_CFGDATA, pbcr);
+ /* printf("PB1CR = %x\n", pbcr); */
}
if (size_b0) {
- mtdcr(ebccfga, pb1cr);
- pbcr = mfdcr(ebccfgd);
- mtdcr(ebccfga, pb1cr);
+ mtdcr(EBC0_CFGADDR, PB1CR);
+ pbcr = mfdcr(EBC0_CFGDATA);
+ mtdcr(EBC0_CFGADDR, PB1CR);
base_b0 = base_b1 - size_b0;
pbcr =
(pbcr & 0x0001ffff) | base_b0 |
(((size_b0 / 1024 / 1024) - 1) << 17);
- mtdcr(ebccfgd, pbcr);
- /* printf("pb0cr = %x\n", pbcr); */
+ mtdcr(EBC0_CFGDATA, pbcr);
+ /* printf("PB0CR = %x\n", pbcr); */
}
size_b0 = flash_get_size((vu_long *) base_b0, &flash_info[0]);
diff --git a/board/amcc/yosemite/yosemite.c b/board/amcc/yosemite/yosemite.c
index 3982896..2a654fa 100644
--- a/board/amcc/yosemite/yosemite.c
+++ b/board/amcc/yosemite/yosemite.c
@@ -40,9 +40,9 @@
/*--------------------------------------------------------------------
* Setup the external bus controller/chip selects
*-------------------------------------------------------------------*/
- mtdcr(ebccfga, xbcfg);
- reg = mfdcr(ebccfgd);
- mtdcr(ebccfgd, reg | 0x04000000); /* Set ATC */
+ mtdcr(EBC0_CFGADDR, EBC0_CFG);
+ reg = mfdcr(EBC0_CFGDATA);
+ mtdcr(EBC0_CFGDATA, reg | 0x04000000); /* Set ATC */
/*--------------------------------------------------------------------
* Setup the GPIO pins
@@ -101,10 +101,10 @@
/*--------------------------------------------------------------------
* Setup other serial configuration
*-------------------------------------------------------------------*/
- mfsdr(sdr_pci0, reg);
- mtsdr(sdr_pci0, 0x80000000 | reg); /* PCI arbiter enabled */
- mtsdr(sdr_pfc0, 0x00003e00); /* Pin function */
- mtsdr(sdr_pfc1, 0x00048000); /* Pin function: UART0 has 4 pins */
+ mfsdr(SDR0_PCI0, reg);
+ mtsdr(SDR0_PCI0, 0x80000000 | reg); /* PCI arbiter enabled */
+ mtsdr(SDR0_PFC0, 0x00003e00); /* Pin function */
+ mtsdr(SDR0_PFC1, 0x00048000); /* Pin function: UART0 has 4 pins */
/*clear tmrclk divisor */
*(unsigned char *)(CONFIG_SYS_BCSR_BASE | 0x04) = 0x00;
@@ -129,8 +129,8 @@
int size_val = 0;
/* Re-do sizing to get full correct info */
- mtdcr(ebccfga, pb0cr);
- pbcr = mfdcr(ebccfgd);
+ mtdcr(EBC0_CFGADDR, PB0CR);
+ pbcr = mfdcr(EBC0_CFGDATA);
switch (gd->bd->bi_flashsize) {
case 1 << 20:
size_val = 0;
@@ -158,8 +158,8 @@
break;
}
pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
- mtdcr(ebccfga, pb0cr);
- mtdcr(ebccfgd, pbcr);
+ mtdcr(EBC0_CFGADDR, PB0CR);
+ mtdcr(EBC0_CFGDATA, pbcr);
/* adjust flash start and offset */
gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
@@ -353,35 +353,35 @@
| Set priority for all PLB3 devices to 0.
| Set PLB3 arbiter to fair mode.
+-------------------------------------------------------------------------*/
- mfsdr(sdr_amp1, addr);
- mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(plb3_acr);
- mtdcr(plb3_acr, addr | 0x80000000);
+ mfsdr(SD0_AMP1, addr);
+ mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
+ addr = mfdcr(PLB3_ACR);
+ mtdcr(PLB3_ACR, addr | 0x80000000);
/*-------------------------------------------------------------------------+
| Set priority for all PLB4 devices to 0.
+-------------------------------------------------------------------------*/
- mfsdr(sdr_amp0, addr);
- mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(plb4_acr) | 0xa0000000; /* Was 0x8---- */
- mtdcr(plb4_acr, addr);
+ mfsdr(SD0_AMP0, addr);
+ mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
+ addr = mfdcr(PLB4_ACR) | 0xa0000000; /* Was 0x8---- */
+ mtdcr(PLB4_ACR, addr);
/*-------------------------------------------------------------------------+
| Set Nebula PLB4 arbiter to fair mode.
+-------------------------------------------------------------------------*/
/* Segment0 */
- addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair;
- addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled;
- addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep;
- addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep;
- mtdcr(plb0_acr, addr);
+ addr = (mfdcr(PLB0_ACR) & ~PLB0_ACR_PPM_MASK) | PLB0_ACR_PPM_FAIR;
+ addr = (addr & ~PLB0_ACR_HBU_MASK) | PLB0_ACR_HBU_ENABLED;
+ addr = (addr & ~PLB0_ACR_RDP_MASK) | PLB0_ACR_RDP_4DEEP;
+ addr = (addr & ~PLB0_ACR_WRP_MASK) | PLB0_ACR_WRP_2DEEP;
+ mtdcr(PLB0_ACR, addr);
/* Segment1 */
- addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair;
- addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled;
- addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep;
- addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep;
- mtdcr(plb1_acr, addr);
+ addr = (mfdcr(PLB1_ACR) & ~PLB1_ACR_PPM_MASK) | PLB1_ACR_PPM_FAIR;
+ addr = (addr & ~PLB1_ACR_HBU_MASK) | PLB1_ACR_HBU_ENABLED;
+ addr = (addr & ~PLB1_ACR_RDP_MASK) | PLB1_ACR_RDP_4DEEP;
+ addr = (addr & ~PLB1_ACR_WRP_MASK) | PLB1_ACR_WRP_2DEEP;
+ mtdcr(PLB1_ACR, addr);
return 1;
}
diff --git a/board/amcc/yucca/flash.c b/board/amcc/yucca/flash.c
index eda49eb..33b97a5 100644
--- a/board/amcc/yucca/flash.c
+++ b/board/amcc/yucca/flash.c
@@ -981,7 +981,7 @@
* Boot Settings in IIC EEprom address 0xA8 or 0xA0
* Read Serial Device Strap Register1 in PPC440SPe
*/
- mfsdr(sdr_sdstp1, val);
+ mfsdr(SDR0_SDSTP1, val);
boot_selection = val & SDR0_SDSTP1_BOOT_SEL_MASK;
ebc_boot_size = val & SDR0_SDSTP1_EBC_ROM_BS_MASK;
diff --git a/board/amcc/yucca/yucca.c b/board/amcc/yucca/yucca.c
index 06c7d62..245004c 100644
--- a/board/amcc/yucca/yucca.c
+++ b/board/amcc/yucca/yucca.c
@@ -167,7 +167,7 @@
| 0x07C00000 - 0 0 000 1 1 1 1 1 0000 0 00000 000000000000
|
+-------------------------------------------------------------------*/
- mtebc(xbcfg, EBC_CFG_LE_UNLOCK |
+ mtebc(EBC0_CFG, EBC_CFG_LE_UNLOCK |
EBC_CFG_PTD_ENABLE |
EBC_CFG_RTC_16PERCLK |
EBC_CFG_ATC_PREVIOUS |
@@ -188,8 +188,8 @@
| boot type
|
+-------------------------------------------------------------------*/
- mtebc(pb1ap, EBC_BXAP_FPGA);
- mtebc(pb1cr, EBC_BXCR_FPGA_CS1);
+ mtebc(PB1AP, EBC_BXAP_FPGA);
+ mtebc(PB1CR, EBC_BXCR_FPGA_CS1);
/*-------------------------------------------------------------------+
|
@@ -334,10 +334,10 @@
break;
}
- mtebc(pb0ap, ebc0_cs0_bxap_value);
- mtebc(pb0cr, ebc0_cs0_bxcr_value);
- mtebc(pb2ap, ebc0_cs2_bxap_value);
- mtebc(pb2cr, ebc0_cs2_bxcr_value);
+ mtebc(PB0AP, ebc0_cs0_bxap_value);
+ mtebc(PB0CR, ebc0_cs0_bxcr_value);
+ mtebc(PB2AP, ebc0_cs2_bxap_value);
+ mtebc(PB2CR, ebc0_cs2_bxcr_value);
/*--------------------------------------------------------------------+
| Interrupt controller setup for the AMCC 440SPe Evaluation board.
@@ -530,9 +530,9 @@
mtdcr (uic0sr, 0x00000000); /* clear all interrupts */
mtdcr (uic0sr, 0xffffffff); /* clear all interrupts */
- mfsdr(sdr_mfr, mfr);
+ mfsdr(SDR0_MFR, mfr);
mfr |= SDR0_MFR_FIXD; /* Workaround for PCI/DMA */
- mtsdr(sdr_mfr, mfr);
+ mtsdr(SDR0_MFR, mfr);
fpga_init();
@@ -608,7 +608,7 @@
* The yucca board is always configured as the host & requires the
* PCI arbiter to be enabled.
*-------------------------------------------------------------------*/
- mfsdr(sdr_sdstp1, strap);
+ mfsdr(SDR0_SDSTP1, strap);
if( (strap & SDR0_SDSTP1_PAE_MASK) == 0 ) {
printf("PCI: SDR0_STRP1[%08lX] - PCI Arbiter disabled.\n",strap);
return 0;
diff --git a/board/cray/L1/L1.c b/board/cray/L1/L1.c
index 8a06ecc..5d1c417 100644
--- a/board/cray/L1/L1.c
+++ b/board/cray/L1/L1.c
@@ -198,8 +198,8 @@
unsigned long tmp;
/* write SDRAM bank 0 register */
- mtdcr (memcfga, mem_mb0cf);
- mtdcr (memcfgd, 0x00062001);
+ mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
+ mtdcr (SDRAM0_CFGDATA, 0x00062001);
/* Set the SDRAM Timing reg, SDTR1 and the refresh timer reg, RTR. */
/* To set the appropriate timings, we need to know the SDRAM speed. */
@@ -212,26 +212,26 @@
/* divisor = ((mfdcr(strap)>> 28) & 0x3); */
/* write SDRAM timing for 100MHz. */
- mtdcr (memcfga, mem_sdtr1);
- mtdcr (memcfgd, 0x0086400D);
+ mtdcr (SDRAM0_CFGADDR, mem_sdtr1);
+ mtdcr (SDRAM0_CFGDATA, 0x0086400D);
/* write SDRAM refresh interval register */
- mtdcr (memcfga, mem_rtr);
- mtdcr (memcfgd, 0x05F00000);
+ mtdcr (SDRAM0_CFGADDR, mem_rtr);
+ mtdcr (SDRAM0_CFGDATA, 0x05F00000);
udelay (200);
/* sdram controller.*/
- mtdcr (memcfga, mem_mcopt1);
- mtdcr (memcfgd, 0x90800000);
+ mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
+ mtdcr (SDRAM0_CFGDATA, 0x90800000);
udelay (200);
/* initially, disable ECC on all banks */
udelay (200);
- mtdcr (memcfga, mem_ecccf);
- tmp = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_ecccf);
+ tmp = mfdcr (SDRAM0_CFGDATA);
tmp &= 0xff0fffff;
- mtdcr (memcfga, mem_ecccf);
- mtdcr (memcfgd, tmp);
+ mtdcr (SDRAM0_CFGADDR, mem_ecccf);
+ mtdcr (SDRAM0_CFGDATA, tmp);
return;
}
@@ -282,18 +282,18 @@
}
printf ("Enable ECC..");
- mtdcr (memcfga, mem_mcopt1);
- tmp = (mfdcr (memcfgd) & ~0xFFE00000) | 0x90800000;
- mtdcr (memcfga, mem_mcopt1);
- mtdcr (memcfgd, tmp);
+ mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
+ tmp = (mfdcr (SDRAM0_CFGDATA) & ~0xFFE00000) | 0x90800000;
+ mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
+ mtdcr (SDRAM0_CFGDATA, tmp);
udelay (600);
for (p = (unsigned long) 0; ((unsigned long) p < L1_MEMSIZE); *p++ = 0L)
;
udelay (400);
- mtdcr (memcfga, mem_ecccf);
- tmp = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_ecccf);
+ tmp = mfdcr (SDRAM0_CFGDATA);
tmp |= 0x00800000;
- mtdcr (memcfgd, tmp);
+ mtdcr (SDRAM0_CFGDATA, tmp);
udelay (400);
printf ("enabled.\n");
return (0);
diff --git a/board/cray/L1/init.S b/board/cray/L1/init.S
index d700ea7..e8dbb93 100644
--- a/board/cray/L1/init.S
+++ b/board/cray/L1/init.S
@@ -87,17 +87,17 @@
/* Peripheral Bank 0 (Flash) initialization */
/*---------------------------------------------------------------------- */
/* 0x7F8FFE80 slowest boot */
- addi r4,0,pb0ap
- mtdcr ebccfga,r4
+ addi r4,0,PB1AP
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,0x9B01
ori r4,r4,0x5480
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
- addi r4,0,pb0cr
- mtdcr ebccfga,r4
+ addi r4,0,PB0CR
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,0xFFC5 /* BAS=0xFFC,BS=0x4(4MB),BU=0x3(R/W), */
ori r4,r4,0x8000 /* BW=0x0( 8 bits) */
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
blr
@@ -125,16 +125,16 @@
/* all reserved bits=0 */
/*---------------------------------------------------------------------- */
/*---------------------------------------------------------------------- */
- addi r4,0,pb1ap
- mtdcr ebccfga,r4
+ addi r4,0,PB1AP
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,0x0185 /* hiword */
ori r4,r4,0x4380 /* loword */
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
- addi r4,0,pb1cr
- mtdcr ebccfga,r4
+ addi r4,0,PB1CR
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,0xF001 /* BAS=0xF00,BS=0x0(1MB),BU=0x3(R/W), */
ori r4,r4,0x8000 /* BW=0x0( 8 bits) */
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
blr
diff --git a/board/csb272/csb272.c b/board/csb272/csb272.c
index 11596d2..cb24cd4 100644
--- a/board/csb272/csb272.c
+++ b/board/csb272/csb272.c
@@ -95,7 +95,7 @@
mtdcr (uicvcr, 0x00000001); /* set vect base=0,INT0 highest priority */
mtdcr (uicsr, 0xFFFFFFFF); /* clear all ints */
- mtebc (epcr, 0xa8400000); /* EBC always driven */
+ mtebc (EBC0_CFG, 0xa8400000); /* EBC always driven */
return 0; /* success */
}
@@ -135,29 +135,29 @@
tot_size = 0;
- mtdcr (memcfga, mem_mb0cf);
- tmp = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
+ tmp = mfdcr (SDRAM0_CFGDATA);
if (tmp & 0x00000001) {
bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
tot_size += bank_size;
}
- mtdcr (memcfga, mem_mb1cf);
- tmp = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_mb1cf);
+ tmp = mfdcr (SDRAM0_CFGDATA);
if (tmp & 0x00000001) {
bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
tot_size += bank_size;
}
- mtdcr (memcfga, mem_mb2cf);
- tmp = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_mb2cf);
+ tmp = mfdcr (SDRAM0_CFGDATA);
if (tmp & 0x00000001) {
bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
tot_size += bank_size;
}
- mtdcr (memcfga, mem_mb3cf);
- tmp = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_mb3cf);
+ tmp = mfdcr (SDRAM0_CFGDATA);
if (tmp & 0x00000001) {
bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
tot_size += bank_size;
diff --git a/board/csb272/init.S b/board/csb272/init.S
index 1cfef37..15b26f8 100644
--- a/board/csb272/init.S
+++ b/board/csb272/init.S
@@ -38,17 +38,17 @@
#define WDCR_EBC(reg,val) \
addi r4,0,reg;\
- mtdcr ebccfga,r4;\
+ mtdcr EBC0_CFGADDR,r4;\
addis r4,0,val@h;\
ori r4,r4,val@l;\
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
#define WDCR_SDRAM(reg,val) \
addi r4,0,reg;\
- mtdcr memcfga,r4;\
+ mtdcr SDRAM0_CFGADDR,r4;\
addis r4,0,val@h;\
ori r4,r4,val@l;\
- mtdcr memcfgd,r4
+ mtdcr SDRAM0_CFGDATA,r4
/******************************************************************************
* Function: ext_bus_cntlr_init
@@ -106,51 +106,51 @@
* SETUP CPC0_CR0
*******************************************************************/
LI32(r4, 0x007000c0)
- mtdcr cntrl0, r4
+ mtdcr CPC0_CR0, r4
/********************************************************************
* Setup CPC0_CR1: Change PCIINT signal to PerWE
*******************************************************************/
- mfdcr r4, cntrl1
+ mfdcr r4, CPC0_CR1
ori r4, r4, 0x4000
- mtdcr cntrl1, r4
+ mtdcr CPC0_CR1, r4
/********************************************************************
* Setup External Bus Controller (EBC).
*******************************************************************/
- WDCR_EBC(epcr, 0xd84c0000)
+ WDCR_EBC(EBC0_CFG, 0xd84c0000)
/********************************************************************
* Memory Bank 0 (Intel 28F128J3 Flash) initialization
*******************************************************************/
- /*WDCR_EBC(pb0ap, 0x02869200)*/
- WDCR_EBC(pb0ap, 0x07869200)
- WDCR_EBC(pb0cr, 0xfe0bc000)
+ /*WDCR_EBC(PB1AP, 0x02869200)*/
+ WDCR_EBC(PB1AP, 0x07869200)
+ WDCR_EBC(PB0CR, 0xfe0bc000)
/********************************************************************
* Memory Bank 1 (Holtek HT6542B PS/2) initialization
*******************************************************************/
- WDCR_EBC(pb1ap, 0x1f869200)
- WDCR_EBC(pb1cr, 0xf0818000)
+ WDCR_EBC(PB1AP, 0x1f869200)
+ WDCR_EBC(PB1CR, 0xf0818000)
/********************************************************************
* Memory Bank 2 (Epson S1D13506) initialization
*******************************************************************/
- WDCR_EBC(pb2ap, 0x05860300)
- WDCR_EBC(pb2cr, 0xf045a000)
+ WDCR_EBC(PB2AP, 0x05860300)
+ WDCR_EBC(PB2CR, 0xf045a000)
/********************************************************************
* Memory Bank 3 (Philips SJA1000 CAN Controllers) initialization
*******************************************************************/
- WDCR_EBC(pb3ap, 0x0387d200)
- WDCR_EBC(pb3cr, 0xf021c000)
+ WDCR_EBC(PB3AP, 0x0387d200)
+ WDCR_EBC(PB3CR, 0xf021c000)
/********************************************************************
* Memory Bank 4-7 (Unused) initialization
*******************************************************************/
- WDCR_EBC(pb4ap, 0)
- WDCR_EBC(pb4cr, 0)
- WDCR_EBC(pb5ap, 0)
- WDCR_EBC(pb5cr, 0)
- WDCR_EBC(pb6ap, 0)
- WDCR_EBC(pb6cr, 0)
- WDCR_EBC(pb7ap, 0)
- WDCR_EBC(pb7cr, 0)
+ WDCR_EBC(PB4AP, 0)
+ WDCR_EBC(PB4CR, 0)
+ WDCR_EBC(PB5AP, 0)
+ WDCR_EBC(PB5CR, 0)
+ WDCR_EBC(PB6AP, 0)
+ WDCR_EBC(PB6CR, 0)
+ WDCR_EBC(PB7AP, 0)
+ WDCR_EBC(PB7CR, 0)
/* We are all done */
mtlr r0 /* Restore link register */
diff --git a/board/csb472/csb472.c b/board/csb472/csb472.c
index 9dc130e..fa0fa19 100644
--- a/board/csb472/csb472.c
+++ b/board/csb472/csb472.c
@@ -63,7 +63,7 @@
mtdcr (uicvcr, 0x00000001); /* set vect base=0,INT0 highest priority */
mtdcr (uicsr, 0xFFFFFFFF); /* clear all ints */
- mtebc (epcr, 0xa8400000); /* EBC always driven */
+ mtebc (EBC0_CFG, 0xa8400000); /* EBC always driven */
return 0; /* success */
}
@@ -103,29 +103,29 @@
tot_size = 0;
- mtdcr (memcfga, mem_mb0cf);
- tmp = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
+ tmp = mfdcr (SDRAM0_CFGDATA);
if (tmp & 0x00000001) {
bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
tot_size += bank_size;
}
- mtdcr (memcfga, mem_mb1cf);
- tmp = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_mb1cf);
+ tmp = mfdcr (SDRAM0_CFGDATA);
if (tmp & 0x00000001) {
bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
tot_size += bank_size;
}
- mtdcr (memcfga, mem_mb2cf);
- tmp = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_mb2cf);
+ tmp = mfdcr (SDRAM0_CFGDATA);
if (tmp & 0x00000001) {
bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
tot_size += bank_size;
}
- mtdcr (memcfga, mem_mb3cf);
- tmp = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_mb3cf);
+ tmp = mfdcr (SDRAM0_CFGDATA);
if (tmp & 0x00000001) {
bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
tot_size += bank_size;
diff --git a/board/csb472/init.S b/board/csb472/init.S
index 2cf8afc..105cb71 100644
--- a/board/csb472/init.S
+++ b/board/csb472/init.S
@@ -38,17 +38,17 @@
#define WDCR_EBC(reg,val) \
addi r4,0,reg;\
- mtdcr ebccfga,r4;\
+ mtdcr EBC0_CFGADDR,r4;\
addis r4,0,val@h;\
ori r4,r4,val@l;\
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
#define WDCR_SDRAM(reg,val) \
addi r4,0,reg;\
- mtdcr memcfga,r4;\
+ mtdcr SDRAM0_CFGADDR,r4;\
addis r4,0,val@h;\
ori r4,r4,val@l;\
- mtdcr memcfgd,r4
+ mtdcr SDRAM0_CFGDATA,r4
/******************************************************************************
* Function: ext_bus_cntlr_init
@@ -106,47 +106,47 @@
* SETUP CPC0_CR0
*******************************************************************/
LI32(r4, 0x00c01030)
- mtdcr cntrl0, r4
+ mtdcr CPC0_CR0, r4
/********************************************************************
* Setup CPC0_CR1: Change PCIINT signal to PerWE
*******************************************************************/
- mfdcr r4, cntrl1
+ mfdcr r4, CPC0_CR1
ori r4, r4, 0x4000
- mtdcr cntrl1, r4
+ mtdcr CPC0_CR1, r4
/********************************************************************
* Setup External Bus Controller (EBC).
*******************************************************************/
- WDCR_EBC(epcr, 0xd84c0000)
+ WDCR_EBC(EBC0_CFG, 0xd84c0000)
/********************************************************************
* Memory Bank 0 (Intel 28F640J3 Flash) initialization
*******************************************************************/
- /*WDCR_EBC(pb0ap, 0x03055200)*/
- /*WDCR_EBC(pb0ap, 0x04055200)*/
- WDCR_EBC(pb0ap, 0x08055200)
- WDCR_EBC(pb0cr, 0xff87a000)
+ /*WDCR_EBC(PB1AP, 0x03055200)*/
+ /*WDCR_EBC(PB1AP, 0x04055200)*/
+ WDCR_EBC(PB1AP, 0x08055200)
+ WDCR_EBC(PB0CR, 0xff87a000)
/********************************************************************
* Memory Bank 3 (Xilinx XC95144 CPLD) initialization
*******************************************************************/
- /*WDCR_EBC(pb3ap, 0x07869200)*/
- WDCR_EBC(pb3ap, 0x04055200)
- WDCR_EBC(pb3cr, 0xf081c000)
+ /*WDCR_EBC(PB3AP, 0x07869200)*/
+ WDCR_EBC(PB3AP, 0x04055200)
+ WDCR_EBC(PB3CR, 0xf081c000)
/********************************************************************
* Memory Bank 1,2,4-7 (Unused) initialization
*******************************************************************/
- WDCR_EBC(pb1ap, 0)
- WDCR_EBC(pb1cr, 0)
- WDCR_EBC(pb2ap, 0)
- WDCR_EBC(pb2cr, 0)
- WDCR_EBC(pb4ap, 0)
- WDCR_EBC(pb4cr, 0)
- WDCR_EBC(pb5ap, 0)
- WDCR_EBC(pb5cr, 0)
- WDCR_EBC(pb6ap, 0)
- WDCR_EBC(pb6cr, 0)
- WDCR_EBC(pb7ap, 0)
- WDCR_EBC(pb7cr, 0)
+ WDCR_EBC(PB1AP, 0)
+ WDCR_EBC(PB1CR, 0)
+ WDCR_EBC(PB2AP, 0)
+ WDCR_EBC(PB2CR, 0)
+ WDCR_EBC(PB4AP, 0)
+ WDCR_EBC(PB4CR, 0)
+ WDCR_EBC(PB5AP, 0)
+ WDCR_EBC(PB5CR, 0)
+ WDCR_EBC(PB6AP, 0)
+ WDCR_EBC(PB6CR, 0)
+ WDCR_EBC(PB7AP, 0)
+ WDCR_EBC(PB7CR, 0)
/* We are all done */
mtlr r0 /* Restore link register */
diff --git a/board/dave/PPChameleonEVB/PPChameleonEVB.c b/board/dave/PPChameleonEVB/PPChameleonEVB.c
index a6aa655..56751e1 100644
--- a/board/dave/PPChameleonEVB/PPChameleonEVB.c
+++ b/board/dave/PPChameleonEVB/PPChameleonEVB.c
@@ -65,9 +65,9 @@
* EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us
*/
#if 1 /* test-only */
- mtebc (epcr, 0xa8400000); /* ebc always driven */
+ mtebc (EBC0_CFG, 0xa8400000); /* ebc always driven */
#else
- mtebc (epcr, 0x28400000); /* ebc in high-z */
+ mtebc (EBC0_CFG, 0x28400000); /* ebc in high-z */
#endif
return 0;
}
@@ -101,7 +101,7 @@
int status;
int index;
int i;
- unsigned long cntrl0Reg;
+ unsigned long CPC0_CR0Reg;
dst = malloc(CONFIG_SYS_FPGA_MAX_SIZE);
if (gunzip (dst, CONFIG_SYS_FPGA_MAX_SIZE, (uchar *)fpgadata, &len) != 0) {
diff --git a/board/dave/PPChameleonEVB/flash.c b/board/dave/PPChameleonEVB/flash.c
index e5a0d3d..237c807 100644
--- a/board/dave/PPChameleonEVB/flash.c
+++ b/board/dave/PPChameleonEVB/flash.c
@@ -75,9 +75,9 @@
debug("[%s, %d] Test point ...\n", __FUNCTION__, __LINE__);
/* Re-do sizing to get full correct info */
- mtdcr(ebccfga, pb0cr);
- pbcr = mfdcr(ebccfgd);
- mtdcr(ebccfga, pb0cr);
+ mtdcr(EBC0_CFGADDR, PB0CR);
+ pbcr = mfdcr(EBC0_CFGDATA);
+ mtdcr(EBC0_CFGADDR, PB0CR);
base = -size;
switch (size) {
case 1 << 20:
@@ -97,7 +97,7 @@
break;
}
pbcr = (pbcr & 0x0001ffff) | base | (size_val << 17);
- mtdcr(ebccfgd, pbcr);
+ mtdcr(EBC0_CFGDATA, pbcr);
debug("[%s, %d] Test point ...\n", __FUNCTION__, __LINE__);
/* Monitor protection ON by default */
diff --git a/board/eric/eric.c b/board/eric/eric.c
index 600b9d7..bc2a907 100644
--- a/board/eric/eric.c
+++ b/board/eric/eric.c
@@ -70,7 +70,7 @@
mtdcr (uicvcr, 0x00000001); /* set vect base=0,INT0 highest priority */
mtdcr (uicsr, 0xFFFFFFFF); /* clear all ints */
- mtdcr (cntrl0, 0x00002000); /* set IRQ6 as GPIO23 to generate an interrupt request to the PCP2PCI bridge */
+ mtdcr (CPC0_CR0, 0x00002000); /* set IRQ6 as GPIO23 to generate an interrupt request to the PCP2PCI bridge */
out32 (PPC405GP_GPIO0_OR, 0x60000000); /*fixme is SMB_INT high or low active??; IRQ6 is GPIO23 output */
out32 (PPC405GP_GPIO0_TCR, 0x7E400000);
diff --git a/board/eric/flash.c b/board/eric/flash.c
index 7e57513..fded412 100644
--- a/board/eric/flash.c
+++ b/board/eric/flash.c
@@ -105,24 +105,24 @@
if (size_b1)
{
- mtdcr(ebccfga, pb0cr);
- pbcr = mfdcr(ebccfgd);
- mtdcr(ebccfga, pb0cr);
+ mtdcr(EBC0_CFGADDR, PB0CR);
+ pbcr = mfdcr(EBC0_CFGDATA);
+ mtdcr(EBC0_CFGADDR, PB0CR);
base_b1 = -size_b1;
pbcr = (pbcr & 0x0001ffff) | base_b1 | (((size_b1/1024/1024)-1)<<17);
- mtdcr(ebccfgd, pbcr);
- /* printf("pb1cr = %x\n", pbcr); */
+ mtdcr(EBC0_CFGDATA, pbcr);
+ /* printf("PB1CR = %x\n", pbcr); */
}
if (size_b0)
{
- mtdcr(ebccfga, pb1cr);
- pbcr = mfdcr(ebccfgd);
- mtdcr(ebccfga, pb1cr);
+ mtdcr(EBC0_CFGADDR, PB1CR);
+ pbcr = mfdcr(EBC0_CFGDATA);
+ mtdcr(EBC0_CFGADDR, PB1CR);
base_b0 = base_b1 - size_b0;
pbcr = (pbcr & 0x0001ffff) | base_b0 | (((size_b0/1024/1024)-1)<<17);
- mtdcr(ebccfgd, pbcr);
- /* printf("pb0cr = %x\n", pbcr); */
+ mtdcr(EBC0_CFGDATA, pbcr);
+ /* printf("PB0CR = %x\n", pbcr); */
}
size_b0 = flash_get_size((volatile FLASH_WORD_SIZE *)base_b0, &flash_info[0]);
diff --git a/board/eric/init.S b/board/eric/init.S
index 4820dd0..16ab11e 100644
--- a/board/eric/init.S
+++ b/board/eric/init.S
@@ -76,129 +76,129 @@
/* Memory Bank 0 (Flash) initialization (from openbios) */
/*----------------------------------------------------------------------- */
- addi r4,0,pb0ap
- mtdcr ebccfga,r4
+ addi r4,0,PB1AP
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,CS0_AP@h
ori r4,r4,CS0_AP@l
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
- addi r4,0,pb0cr
- mtdcr ebccfga,r4
+ addi r4,0,PB0CR
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,CS0_CR@h
ori r4,r4,CS0_CR@l
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
/*----------------------------------------------------------------------- */
/* Memory Bank 1 (NVRAM/RTC) initialization */
/*----------------------------------------------------------------------- */
- addi r4,0,pb1ap
- mtdcr ebccfga,r4
+ addi r4,0,PB1AP
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,CS1_AP@h
ori r4,r4,CS1_AP@l
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
- addi r4,0,pb1cr
- mtdcr ebccfga,r4
+ addi r4,0,PB1CR
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,CS1_CR@h
ori r4,r4,CS1_CR@l
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
/*----------------------------------------------------------------------- */
/* Memory Bank 2 (A/D converter) initialization */
/*----------------------------------------------------------------------- */
- addi r4,0,pb2ap
- mtdcr ebccfga,r4
+ addi r4,0,PB2AP
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,CS2_AP@h
ori r4,r4,CS2_AP@l
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
- addi r4,0,pb2cr
- mtdcr ebccfga,r4
+ addi r4,0,PB2CR
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,CS2_CR@h
ori r4,r4,CS2_CR@l
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
/*----------------------------------------------------------------------- */
/* Memory Bank 3 (Ethernet PHY Reset) initialization */
/*----------------------------------------------------------------------- */
- addi r4,0,pb3ap
- mtdcr ebccfga,r4
+ addi r4,0,PB3AP
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,CS3_AP@h
ori r4,r4,CS3_AP@l
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
- addi r4,0,pb3cr
- mtdcr ebccfga,r4
+ addi r4,0,PB3CR
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,CS3_CR@h
ori r4,r4,CS3_CR@l
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
/*----------------------------------------------------------------------- */
/* Memory Bank 4 (PC-MIP PRSNT1#) initialization */
/*----------------------------------------------------------------------- */
- addi r4,0,pb4ap
- mtdcr ebccfga,r4
+ addi r4,0,PB4AP
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,CS4_AP@h
ori r4,r4,CS4_AP@l
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
- addi r4,0,pb4cr
- mtdcr ebccfga,r4
+ addi r4,0,PB4CR
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,CS4_CR@h
ori r4,r4,CS4_CR@l
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
/*----------------------------------------------------------------------- */
/* Memory Bank 5 (PC-MIP PRSNT2#) initialization */
/*----------------------------------------------------------------------- */
- addi r4,0,pb5ap
- mtdcr ebccfga,r4
+ addi r4,0,PB5AP
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,CS5_AP@h
ori r4,r4,CS5_AP@l
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
- addi r4,0,pb5cr
- mtdcr ebccfga,r4
+ addi r4,0,PB5CR
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,CS5_CR@h
ori r4,r4,CS5_CR@l
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
/*----------------------------------------------------------------------- */
/* Memory Bank 6 (CPU LED0) initialization */
/*----------------------------------------------------------------------- */
- addi r4,0,pb6ap
- mtdcr ebccfga,r4
+ addi r4,0,PB6AP
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,CS6_AP@h
ori r4,r4,CS6_AP@l
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
- addi r4,0,pb6cr
- mtdcr ebccfga,r4
+ addi r4,0,PB6CR
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,CS6_CR@h
ori r4,r4,CS5_CR@l
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
/*----------------------------------------------------------------------- */
/* Memory Bank 7 (CPU LED1) initialization */
/*----------------------------------------------------------------------- */
- addi r4,0,pb7ap
- mtdcr ebccfga,r4
+ addi r4,0,PB7AP
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,CS7_AP@h
ori r4,r4,CS7_AP@l
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
- addi r4,0,pb7cr
- mtdcr ebccfga,r4
+ addi r4,0,PB7CR
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,CS7_CR@h
ori r4,r4,CS7_CR@l
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
/* addis r4,r0,FPGA_BRDC@h */
/* ori r4,r4,FPGA_BRDC@l */
@@ -229,40 +229,40 @@
/*------------------------------------------------------------------- */
addi r4,0,mem_mb0cf
- mtdcr memcfga,r4
+ mtdcr SDRAM0_CFGADDR,r4
addis r4,0,MB0CF@h
ori r4,r4,MB0CF@l
- mtdcr memcfgd,r4
+ mtdcr SDRAM0_CFGDATA,r4
/*------------------------------------------------------------------- */
/* Set MB1CF for bank 1. (32MB-64MB) Address Mode 4 since 12x8(2) */
/*------------------------------------------------------------------- */
addi r4,0,mem_mb1cf
- mtdcr memcfga,r4
+ mtdcr SDRAM0_CFGADDR,r4
addis r4,0,MB1CF@h
ori r4,r4,MB1CF@l
- mtdcr memcfgd,r4
+ mtdcr SDRAM0_CFGDATA,r4
/*------------------------------------------------------------------- */
/* Set MB2CF for bank 2. off */
/*------------------------------------------------------------------- */
addi r4,0,mem_mb2cf
- mtdcr memcfga,r4
+ mtdcr SDRAM0_CFGADDR,r4
addis r4,0,MB2CF@h
ori r4,r4,MB2CF@l
- mtdcr memcfgd,r4
+ mtdcr SDRAM0_CFGDATA,r4
/*------------------------------------------------------------------- */
/* Set MB3CF for bank 3. off */
/*------------------------------------------------------------------- */
addi r4,0,mem_mb3cf
- mtdcr memcfga,r4
+ mtdcr SDRAM0_CFGADDR,r4
addis r4,0,MB3CF@h
ori r4,r4,MB3CF@l
- mtdcr memcfgd,r4
+ mtdcr SDRAM0_CFGDATA,r4
/*------------------------------------------------------------------- */
/* Set the SDRAM Timing reg, SDTR1 and the refresh timer reg, RTR. */
@@ -276,7 +276,7 @@
/* maybe 133Mhz. */
/*------------------------------------------------------------------- */
- mfdcr r5,strap /* determine FBK divider */
+ mfdcr r5,CPC0_PSR /* determine FBK divider */
/* via STRAP reg to calc PLB speed. */
/* SDRAM speed is the same as the PLB */
/* speed. */
@@ -306,15 +306,15 @@
/* Set SDTR1 */
/*------------------------------------------------------------------- */
addi r4,0,mem_sdtr1
- mtdcr memcfga,r4
- mtdcr memcfgd,r6
+ mtdcr SDRAM0_CFGADDR,r4
+ mtdcr SDRAM0_CFGDATA,r6
/*------------------------------------------------------------------- */
/* Set RTR */
/*------------------------------------------------------------------- */
addi r4,0,mem_rtr
- mtdcr memcfga,r4
- mtdcr memcfgd,r7
+ mtdcr SDRAM0_CFGADDR,r4
+ mtdcr SDRAM0_CFGDATA,r7
/*------------------------------------------------------------------- */
/* Delay to ensure 200usec have elapsed since reset. Assume worst */
@@ -333,10 +333,10 @@
/* read/prefetch. */
/*------------------------------------------------------------------- */
addi r4,0,mem_mcopt1
- mtdcr memcfga,r4
+ mtdcr SDRAM0_CFGADDR,r4
addis r4,0,0x8080 /* set DC_EN=1 */
ori r4,r4,0x0000
- mtdcr memcfgd,r4
+ mtdcr SDRAM0_CFGDATA,r4
/*------------------------------------------------------------------- */
/* Delay to ensure 10msec have elapsed since reset. This is */
diff --git a/board/esd/apc405/apc405.c b/board/esd/apc405/apc405.c
index 5a02155..46622a2 100644
--- a/board/esd/apc405/apc405.c
+++ b/board/esd/apc405/apc405.c
@@ -92,7 +92,7 @@
int board_revision(void)
{
- unsigned long cntrl0Reg;
+ unsigned long CPC0_CR0Reg;
unsigned long value;
/*
@@ -100,8 +100,8 @@
*/
/* Setup GPIO pins (CS2/GPIO11, CS3/GPIO12 and CS4/GPIO13 as GPIO) */
- cntrl0Reg = mfdcr(cntrl0);
- mtdcr(cntrl0, cntrl0Reg | 0x03800000);
+ CPC0_CR0Reg = mfdcr(CPC0_CR0);
+ mtdcr(CPC0_CR0, CPC0_CR0Reg | 0x03800000);
out_be32((void*)GPIO0_ODR, in_be32((void*)GPIO0_ODR) & ~0x001c0000);
out_be32((void*)GPIO0_TCR, in_be32((void*)GPIO0_TCR) & ~0x001c0000);
@@ -113,7 +113,7 @@
/*
* Restore GPIO settings
*/
- mtdcr(cntrl0, cntrl0Reg);
+ mtdcr(CPC0_CR0, CPC0_CR0Reg);
switch (value) {
case 0x001c0000:
@@ -166,7 +166,7 @@
/*
* EBC Configuration Register: set ready timeout to 512 ebc-clks
*/
- mtebc(epcr, 0xa8400000); /* ebc always driven */
+ mtebc(EBC0_CFG, 0xa8400000); /* ebc always driven */
/*
* New boards have a single 32MB flash connected to CS0
@@ -174,12 +174,12 @@
*/
if (board_revision() >= 8) {
/* disable CS1 */
- mtebc(pb1ap, 0);
- mtebc(pb1cr, 0);
+ mtebc(PB1AP, 0);
+ mtebc(PB1CR, 0);
/* resize CS0 to 32MB */
- mtebc(pb0ap, CONFIG_SYS_EBC_PB0AP_HWREV8);
- mtebc(pb0cr, CONFIG_SYS_EBC_PB0CR_HWREV8);
+ mtebc(PB0AP, CONFIG_SYS_EBC_PB0AP_HWREV8);
+ mtebc(PB0CR, CONFIG_SYS_EBC_PB0CR_HWREV8);
}
return 0;
@@ -209,7 +209,7 @@
int status;
int index;
int i;
- unsigned long cntrl0Reg;
+ unsigned long CPC0_CR0Reg;
char *str;
uchar *logo_addr;
ulong logo_size;
@@ -219,8 +219,8 @@
/*
* Setup GPIO pins (CS6+CS7 as GPIO)
*/
- cntrl0Reg = mfdcr(cntrl0);
- mtdcr(cntrl0, cntrl0Reg | 0x00300000);
+ CPC0_CR0Reg = mfdcr(CPC0_CR0);
+ mtdcr(CPC0_CR0, CPC0_CR0Reg | 0x00300000);
dst = malloc(CONFIG_SYS_FPGA_MAX_SIZE);
if (gunzip(dst, CONFIG_SYS_FPGA_MAX_SIZE, (uchar *)fpgadata, &len) != 0) {
@@ -265,7 +265,7 @@
}
/* restore gpio/cs settings */
- mtdcr(cntrl0, cntrl0Reg);
+ mtdcr(CPC0_CR0, CPC0_CR0Reg);
puts("FPGA: ");
diff --git a/board/esd/ar405/flash.c b/board/esd/ar405/flash.c
index 274ada9..a53122b 100644
--- a/board/esd/ar405/flash.c
+++ b/board/esd/ar405/flash.c
@@ -65,9 +65,9 @@
flash_get_offsets (-size_b0, &flash_info[0]);
/* Re-do sizing to get full correct info */
- mtdcr(ebccfga, pb0cr);
- pbcr = mfdcr(ebccfgd);
- mtdcr(ebccfga, pb0cr);
+ mtdcr(EBC0_CFGADDR, PB0CR);
+ pbcr = mfdcr(EBC0_CFGDATA);
+ mtdcr(EBC0_CFGADDR, PB0CR);
base_b0 = -size_b0;
switch (size_b0) {
case 1 << 20:
@@ -87,7 +87,7 @@
break;
}
pbcr = (pbcr & 0x0001ffff) | base_b0 | (size_val << 17);
- mtdcr(ebccfgd, pbcr);
+ mtdcr(EBC0_CFGDATA, pbcr);
/* Monitor protection ON by default */
(void)flash_protect(FLAG_PROTECT_SET,
diff --git a/board/esd/ash405/ash405.c b/board/esd/ash405/ash405.c
index 074fe08..8da08fa 100644
--- a/board/esd/ash405/ash405.c
+++ b/board/esd/ash405/ash405.c
@@ -77,7 +77,7 @@
/*
* EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us
*/
- mtebc (epcr, 0xa8400000); /* ebc always driven */
+ mtebc (EBC0_CFG, 0xa8400000); /* ebc always driven */
return 0;
}
diff --git a/board/esd/ash405/flash.c b/board/esd/ash405/flash.c
index 274ada9..a53122b 100644
--- a/board/esd/ash405/flash.c
+++ b/board/esd/ash405/flash.c
@@ -65,9 +65,9 @@
flash_get_offsets (-size_b0, &flash_info[0]);
/* Re-do sizing to get full correct info */
- mtdcr(ebccfga, pb0cr);
- pbcr = mfdcr(ebccfgd);
- mtdcr(ebccfga, pb0cr);
+ mtdcr(EBC0_CFGADDR, PB0CR);
+ pbcr = mfdcr(EBC0_CFGDATA);
+ mtdcr(EBC0_CFGADDR, PB0CR);
base_b0 = -size_b0;
switch (size_b0) {
case 1 << 20:
@@ -87,7 +87,7 @@
break;
}
pbcr = (pbcr & 0x0001ffff) | base_b0 | (size_val << 17);
- mtdcr(ebccfgd, pbcr);
+ mtdcr(EBC0_CFGDATA, pbcr);
/* Monitor protection ON by default */
(void)flash_protect(FLAG_PROTECT_SET,
diff --git a/board/esd/canbt/canbt.c b/board/esd/canbt/canbt.c
index 2fe6b7b..418d3e2 100644
--- a/board/esd/canbt/canbt.c
+++ b/board/esd/canbt/canbt.c
@@ -52,16 +52,16 @@
int board_early_init_f (void)
{
- unsigned long cntrl0Reg;
+ unsigned long CPC0_CR0Reg;
int index, len, i;
int status;
/*
* Setup GPIO pins
*/
- cntrl0Reg = mfdcr (cntrl0) & 0xf0001fff;
- cntrl0Reg |= 0x0070f000;
- mtdcr (cntrl0, cntrl0Reg);
+ CPC0_CR0Reg = mfdcr (CPC0_CR0) & 0xf0001fff;
+ CPC0_CR0Reg |= 0x0070f000;
+ mtdcr (CPC0_CR0, CPC0_CR0Reg);
#ifdef FPGA_DEBUG
/* set up serial port with default baudrate */
diff --git a/board/esd/canbt/flash.c b/board/esd/canbt/flash.c
index 56c822e..224dde4 100644
--- a/board/esd/canbt/flash.c
+++ b/board/esd/canbt/flash.c
@@ -64,13 +64,13 @@
flash_get_offsets (-size_b0, &flash_info[0]);
/* Re-do sizing to get full correct info */
- mtdcr(ebccfga, pb0cr);
- pbcr = mfdcr(ebccfgd);
- mtdcr(ebccfga, pb0cr);
+ mtdcr(EBC0_CFGADDR, PB0CR);
+ pbcr = mfdcr(EBC0_CFGDATA);
+ mtdcr(EBC0_CFGADDR, PB0CR);
base_b0 = -size_b0;
pbcr = (pbcr & 0x0001ffff) | base_b0 | (((size_b0/1024/1024)-1)<<17);
- mtdcr(ebccfgd, pbcr);
- /* printf("pb1cr = %x\n", pbcr); */
+ mtdcr(EBC0_CFGDATA, pbcr);
+ /* printf("PB1CR = %x\n", pbcr); */
/* Monitor protection ON by default */
(void)flash_protect(FLAG_PROTECT_SET,
diff --git a/board/esd/cms700/cms700.c b/board/esd/cms700/cms700.c
index 01b1223..7a92401 100644
--- a/board/esd/cms700/cms700.c
+++ b/board/esd/cms700/cms700.c
@@ -56,7 +56,7 @@
/*
* EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us
*/
- mtebc (epcr, 0xa8400000); /* ebc always driven */
+ mtebc (EBC0_CFG, 0xa8400000); /* ebc always driven */
/*
* Reset CPLD via GPIO12 (CS3) pin
diff --git a/board/esd/cms700/flash.c b/board/esd/cms700/flash.c
index 274ada9..a53122b 100644
--- a/board/esd/cms700/flash.c
+++ b/board/esd/cms700/flash.c
@@ -65,9 +65,9 @@
flash_get_offsets (-size_b0, &flash_info[0]);
/* Re-do sizing to get full correct info */
- mtdcr(ebccfga, pb0cr);
- pbcr = mfdcr(ebccfgd);
- mtdcr(ebccfga, pb0cr);
+ mtdcr(EBC0_CFGADDR, PB0CR);
+ pbcr = mfdcr(EBC0_CFGDATA);
+ mtdcr(EBC0_CFGADDR, PB0CR);
base_b0 = -size_b0;
switch (size_b0) {
case 1 << 20:
@@ -87,7 +87,7 @@
break;
}
pbcr = (pbcr & 0x0001ffff) | base_b0 | (size_val << 17);
- mtdcr(ebccfgd, pbcr);
+ mtdcr(EBC0_CFGDATA, pbcr);
/* Monitor protection ON by default */
(void)flash_protect(FLAG_PROTECT_SET,
diff --git a/board/esd/cpci2dp/cpci2dp.c b/board/esd/cpci2dp/cpci2dp.c
index cd57ed4..00c7024 100644
--- a/board/esd/cpci2dp/cpci2dp.c
+++ b/board/esd/cpci2dp/cpci2dp.c
@@ -31,13 +31,13 @@
int board_early_init_f (void)
{
- unsigned long cntrl0Reg;
+ unsigned long CPC0_CR0Reg;
/*
* Setup GPIO pins
*/
- cntrl0Reg = mfdcr(cntrl0);
- mtdcr(cntrl0, cntrl0Reg |
+ CPC0_CR0Reg = mfdcr(CPC0_CR0);
+ mtdcr(CPC0_CR0, CPC0_CR0Reg |
((CONFIG_SYS_EEPROM_WP | CONFIG_SYS_PB_LED |
CONFIG_SYS_SELF_RST | CONFIG_SYS_INTA_FAKE) << 5));
@@ -72,7 +72,7 @@
int misc_init_r (void)
{
- unsigned long cntrl0Reg;
+ unsigned long CPC0_CR0Reg;
/* adjust flash start and offset */
gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
@@ -81,8 +81,8 @@
/*
* Select cts (and not dsr) on uart1
*/
- cntrl0Reg = mfdcr(cntrl0);
- mtdcr(cntrl0, cntrl0Reg | 0x00001000);
+ CPC0_CR0Reg = mfdcr(CPC0_CR0);
+ mtdcr(CPC0_CR0, CPC0_CR0Reg | 0x00001000);
return (0);
}
diff --git a/board/esd/cpci2dp/flash.c b/board/esd/cpci2dp/flash.c
index 56c822e..224dde4 100644
--- a/board/esd/cpci2dp/flash.c
+++ b/board/esd/cpci2dp/flash.c
@@ -64,13 +64,13 @@
flash_get_offsets (-size_b0, &flash_info[0]);
/* Re-do sizing to get full correct info */
- mtdcr(ebccfga, pb0cr);
- pbcr = mfdcr(ebccfgd);
- mtdcr(ebccfga, pb0cr);
+ mtdcr(EBC0_CFGADDR, PB0CR);
+ pbcr = mfdcr(EBC0_CFGDATA);
+ mtdcr(EBC0_CFGADDR, PB0CR);
base_b0 = -size_b0;
pbcr = (pbcr & 0x0001ffff) | base_b0 | (((size_b0/1024/1024)-1)<<17);
- mtdcr(ebccfgd, pbcr);
- /* printf("pb1cr = %x\n", pbcr); */
+ mtdcr(EBC0_CFGDATA, pbcr);
+ /* printf("PB1CR = %x\n", pbcr); */
/* Monitor protection ON by default */
(void)flash_protect(FLAG_PROTECT_SET,
diff --git a/board/esd/cpci405/cpci405.c b/board/esd/cpci405/cpci405.c
index a677c62..4c9ed2f 100644
--- a/board/esd/cpci405/cpci405.c
+++ b/board/esd/cpci405/cpci405.c
@@ -214,7 +214,7 @@
int cpci405_host(void)
{
- if (mfdcr(strap) & PSR_PCI_ARBIT_EN)
+ if (mfdcr(CPC0_PSR) & PSR_PCI_ARBIT_EN)
return -1; /* yes, board is cpci405 host */
else
return 0; /* no, board is cpci405 adapter */
@@ -222,14 +222,14 @@
int cpci405_version(void)
{
- unsigned long cntrl0Reg;
+ unsigned long CPC0_CR0Reg;
unsigned long value;
/*
* Setup GPIO pins (CS2/GPIO11 and CS3/GPIO12 as GPIO)
*/
- cntrl0Reg = mfdcr(cntrl0);
- mtdcr(cntrl0, cntrl0Reg | 0x03000000);
+ CPC0_CR0Reg = mfdcr(CPC0_CR0);
+ mtdcr(CPC0_CR0, CPC0_CR0Reg | 0x03000000);
out_be32((void*)GPIO0_ODR, in_be32((void*)GPIO0_ODR) & ~0x00180000);
out_be32((void*)GPIO0_TCR, in_be32((void*)GPIO0_TCR) & ~0x00180000);
udelay(1000); /* wait some time before reading input */
@@ -238,7 +238,7 @@
/*
* Restore GPIO settings
*/
- mtdcr(cntrl0, cntrl0Reg);
+ mtdcr(CPC0_CR0, CPC0_CR0Reg);
switch (value) {
case 0x00180000:
@@ -261,7 +261,7 @@
int misc_init_r (void)
{
- unsigned long cntrl0Reg;
+ unsigned long CPC0_CR0Reg;
/* adjust flash start and offset */
gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
@@ -283,8 +283,8 @@
/*
* Setup GPIO pins (CS6+CS7 as GPIO)
*/
- cntrl0Reg = mfdcr(cntrl0);
- mtdcr(cntrl0, cntrl0Reg | 0x00300000);
+ CPC0_CR0Reg = mfdcr(CPC0_CR0);
+ mtdcr(CPC0_CR0, CPC0_CR0Reg | 0x00300000);
dst = malloc(CONFIG_SYS_FPGA_MAX_SIZE);
if (gunzip(dst, CONFIG_SYS_FPGA_MAX_SIZE,
@@ -330,7 +330,7 @@
}
/* restore gpio/cs settings */
- mtdcr(cntrl0, cntrl0Reg);
+ mtdcr(CPC0_CR0, CPC0_CR0Reg);
puts("FPGA: ");
@@ -400,8 +400,8 @@
/*
* Select cts (and not dsr) on uart1
*/
- cntrl0Reg = mfdcr(cntrl0);
- mtdcr(cntrl0, cntrl0Reg | 0x00001000);
+ CPC0_CR0Reg = mfdcr(CPC0_CR0);
+ mtdcr(CPC0_CR0, CPC0_CR0Reg | 0x00001000);
return 0;
}
diff --git a/board/esd/cpci405/flash.c b/board/esd/cpci405/flash.c
index d535924..4fcf174 100644
--- a/board/esd/cpci405/flash.c
+++ b/board/esd/cpci405/flash.c
@@ -91,13 +91,13 @@
size_b1 = 1 << 20;
}
base_b1 = -size_b1;
- mtdcr (ebccfga, pb0cr);
- pbcr = mfdcr (ebccfgd);
- mtdcr (ebccfga, pb0cr);
+ mtdcr (EBC0_CFGADDR, PB0CR);
+ pbcr = mfdcr (EBC0_CFGDATA);
+ mtdcr (EBC0_CFGADDR, PB0CR);
pbcr = (pbcr & 0x0001ffff) | base_b1 | (calc_size(size_b1) << 17);
- mtdcr (ebccfgd, pbcr);
+ mtdcr (EBC0_CFGDATA, pbcr);
#if 0 /* test-only */
- printf("size_b1=%x base_b1=%x pb1cr = %x\n",
+ printf("size_b1=%x base_b1=%x PB1CR = %x\n",
size_b1, base_b1, pbcr); /* test-only */
#endif
}
@@ -108,13 +108,13 @@
size_b0 = 1 << 20;
}
base_b0 = base_b1 - size_b0;
- mtdcr (ebccfga, pb1cr);
- pbcr = mfdcr (ebccfgd);
- mtdcr (ebccfga, pb1cr);
+ mtdcr (EBC0_CFGADDR, PB1CR);
+ pbcr = mfdcr (EBC0_CFGDATA);
+ mtdcr (EBC0_CFGADDR, PB1CR);
pbcr = (pbcr & 0x0001ffff) | base_b0 | (calc_size(size_b0) << 17);
- mtdcr (ebccfgd, pbcr);
+ mtdcr (EBC0_CFGDATA, pbcr);
#if 0 /* test-only */
- printf("size_b0=%x base_b0=%x pb0cr = %x\n",
+ printf("size_b0=%x base_b0=%x PB0CR = %x\n",
size_b0, base_b0, pbcr); /* test-only */
#endif
}
diff --git a/board/esd/cpciiser4/flash.c b/board/esd/cpciiser4/flash.c
index 56c822e..224dde4 100644
--- a/board/esd/cpciiser4/flash.c
+++ b/board/esd/cpciiser4/flash.c
@@ -64,13 +64,13 @@
flash_get_offsets (-size_b0, &flash_info[0]);
/* Re-do sizing to get full correct info */
- mtdcr(ebccfga, pb0cr);
- pbcr = mfdcr(ebccfgd);
- mtdcr(ebccfga, pb0cr);
+ mtdcr(EBC0_CFGADDR, PB0CR);
+ pbcr = mfdcr(EBC0_CFGDATA);
+ mtdcr(EBC0_CFGADDR, PB0CR);
base_b0 = -size_b0;
pbcr = (pbcr & 0x0001ffff) | base_b0 | (((size_b0/1024/1024)-1)<<17);
- mtdcr(ebccfgd, pbcr);
- /* printf("pb1cr = %x\n", pbcr); */
+ mtdcr(EBC0_CFGDATA, pbcr);
+ /* printf("PB1CR = %x\n", pbcr); */
/* Monitor protection ON by default */
(void)flash_protect(FLAG_PROTECT_SET,
diff --git a/board/esd/dp405/dp405.c b/board/esd/dp405/dp405.c
index e52d37b..fc0d091 100644
--- a/board/esd/dp405/dp405.c
+++ b/board/esd/dp405/dp405.c
@@ -54,7 +54,7 @@
/*
* EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us
*/
- mtebc (epcr, 0xa8400000); /* ebc always driven */
+ mtebc (EBC0_CFG, 0xa8400000); /* ebc always driven */
/*
* Reset CPLD via GPIO13 (CS4) pin
diff --git a/board/esd/dp405/flash.c b/board/esd/dp405/flash.c
index 274ada9..a53122b 100644
--- a/board/esd/dp405/flash.c
+++ b/board/esd/dp405/flash.c
@@ -65,9 +65,9 @@
flash_get_offsets (-size_b0, &flash_info[0]);
/* Re-do sizing to get full correct info */
- mtdcr(ebccfga, pb0cr);
- pbcr = mfdcr(ebccfgd);
- mtdcr(ebccfga, pb0cr);
+ mtdcr(EBC0_CFGADDR, PB0CR);
+ pbcr = mfdcr(EBC0_CFGDATA);
+ mtdcr(EBC0_CFGADDR, PB0CR);
base_b0 = -size_b0;
switch (size_b0) {
case 1 << 20:
@@ -87,7 +87,7 @@
break;
}
pbcr = (pbcr & 0x0001ffff) | base_b0 | (size_val << 17);
- mtdcr(ebccfgd, pbcr);
+ mtdcr(EBC0_CFGDATA, pbcr);
/* Monitor protection ON by default */
(void)flash_protect(FLAG_PROTECT_SET,
diff --git a/board/esd/du405/du405.c b/board/esd/du405/du405.c
index 8e9ac28..28a50c7 100644
--- a/board/esd/du405/du405.c
+++ b/board/esd/du405/du405.c
@@ -135,7 +135,7 @@
/*
* EBC Configuration Register: set ready timeout to 100 us
*/
- mtebc (epcr, 0xb8400000);
+ mtebc (EBC0_CFG, 0xb8400000);
return 0;
}
@@ -143,13 +143,13 @@
int misc_init_r (void)
{
- unsigned long cntrl0Reg;
+ unsigned long CPC0_CR0Reg;
/*
* Setup UART1 handshaking: use CTS instead of DSR
*/
- cntrl0Reg = mfdcr(cntrl0);
- mtdcr(cntrl0, cntrl0Reg | 0x00001000);
+ CPC0_CR0Reg = mfdcr(CPC0_CR0);
+ mtdcr(CPC0_CR0, CPC0_CR0Reg | 0x00001000);
return (0);
}
diff --git a/board/esd/du405/flash.c b/board/esd/du405/flash.c
index 240aa09..c62c6a9 100644
--- a/board/esd/du405/flash.c
+++ b/board/esd/du405/flash.c
@@ -67,25 +67,25 @@
/* Re-do sizing to get full correct info */
if (size_b1) {
- mtdcr (ebccfga, pb0cr);
- pbcr = mfdcr (ebccfgd);
- mtdcr (ebccfga, pb0cr);
+ mtdcr (EBC0_CFGADDR, PB0CR);
+ pbcr = mfdcr (EBC0_CFGDATA);
+ mtdcr (EBC0_CFGADDR, PB0CR);
base_b1 = -size_b1;
pbcr = (pbcr & 0x0001ffff) | base_b1 |
(((size_b1 / 1024 / 1024) - 1) << 17);
- mtdcr (ebccfgd, pbcr);
- /* printf("pb1cr = %x\n", pbcr); */
+ mtdcr (EBC0_CFGDATA, pbcr);
+ /* printf("PB1CR = %x\n", pbcr); */
}
if (size_b0) {
- mtdcr (ebccfga, pb1cr);
- pbcr = mfdcr (ebccfgd);
- mtdcr (ebccfga, pb1cr);
+ mtdcr (EBC0_CFGADDR, PB1CR);
+ pbcr = mfdcr (EBC0_CFGDATA);
+ mtdcr (EBC0_CFGADDR, PB1CR);
base_b0 = base_b1 - size_b0;
pbcr = (pbcr & 0x0001ffff) | base_b0 |
(((size_b0 / 1024 / 1024) - 1) << 17);
- mtdcr (ebccfgd, pbcr);
- /* printf("pb0cr = %x\n", pbcr); */
+ mtdcr (EBC0_CFGDATA, pbcr);
+ /* printf("PB0CR = %x\n", pbcr); */
}
size_b0 = flash_get_size ((vu_long *) base_b0, &flash_info[0]);
diff --git a/board/esd/du440/du440.c b/board/esd/du440/du440.c
index 0ec519b..376de98 100644
--- a/board/esd/du440/du440.c
+++ b/board/esd/du440/du440.c
@@ -45,8 +45,8 @@
u32 sdr0_pfc1, sdr0_pfc2;
u32 reg;
- mtdcr(ebccfga, xbcfg);
- mtdcr(ebccfgd, 0xb8400000);
+ mtdcr(EBC0_CFGADDR, EBC0_CFG);
+ mtdcr(EBC0_CFGDATA, 0xb8400000);
/*
* Setup the GPIO pins
@@ -145,8 +145,8 @@
mtsdr(SDR0_PFC1, sdr0_pfc1);
/* PCI arbiter enabled */
- mfsdr(sdr_pci0, reg);
- mtsdr(sdr_pci0, 0x80000000 | reg);
+ mfsdr(SDR0_PCI0, reg);
+ mtsdr(SDR0_PCI0, 0x80000000 | reg);
/* setup NAND FLASH */
mfsdr(SDR0_CUST0, sdr0_cust0);
@@ -176,12 +176,12 @@
gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
gd->bd->bi_flashoffset = 0;
- mtdcr(ebccfga, pb0cr);
- pbcr = mfdcr(ebccfgd);
+ mtdcr(EBC0_CFGADDR, PB0CR);
+ pbcr = mfdcr(EBC0_CFGDATA);
size_val = ffs(gd->bd->bi_flashsize) - 21;
pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
- mtdcr(ebccfga, pb0cr);
- mtdcr(ebccfgd, pbcr);
+ mtdcr(EBC0_CFGADDR, PB0CR);
+ mtdcr(EBC0_CFGDATA, pbcr);
/*
* Re-check to get correct base address
@@ -265,8 +265,8 @@
* This fix will make the MAL burst disabling patch for the Linux
* EMAC driver obsolete.
*/
- reg = mfdcr(plb4_acr) & ~PLB4_ACR_WRP;
- mtdcr(plb4_acr, reg);
+ reg = mfdcr(PLB4_ACR) & ~PLB4_ACR_WRP;
+ mtdcr(PLB4_ACR, reg);
/*
* release IO-RST#
@@ -380,35 +380,35 @@
* Set priority for all PLB3 devices to 0.
* Set PLB3 arbiter to fair mode.
*/
- mfsdr(sdr_amp1, addr);
- mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(plb3_acr);
- mtdcr(plb3_acr, addr | 0x80000000);
+ mfsdr(SD0_AMP1, addr);
+ mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
+ addr = mfdcr(PLB3_ACR);
+ mtdcr(PLB3_ACR, addr | 0x80000000);
/*
* Set priority for all PLB4 devices to 0.
*/
- mfsdr(sdr_amp0, addr);
- mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(plb4_acr) | 0xa0000000; /* Was 0x8---- */
- mtdcr(plb4_acr, addr);
+ mfsdr(SD0_AMP0, addr);
+ mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
+ addr = mfdcr(PLB4_ACR) | 0xa0000000; /* Was 0x8---- */
+ mtdcr(PLB4_ACR, addr);
/*
* Set Nebula PLB4 arbiter to fair mode.
*/
/* Segment0 */
- addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair;
- addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled;
- addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep;
- addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep;
- mtdcr(plb0_acr, addr);
+ addr = (mfdcr(PLB0_ACR) & ~PLB0_ACR_PPM_MASK) | PLB0_ACR_PPM_FAIR;
+ addr = (addr & ~PLB0_ACR_HBU_MASK) | PLB0_ACR_HBU_ENABLED;
+ addr = (addr & ~PLB0_ACR_RDP_MASK) | PLB0_ACR_RDP_4DEEP;
+ addr = (addr & ~PLB0_ACR_WRP_MASK) | PLB0_ACR_WRP_2DEEP;
+ mtdcr(PLB0_ACR, addr);
/* Segment1 */
- addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair;
- addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled;
- addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep;
- addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep;
- mtdcr(plb1_acr, addr);
+ addr = (mfdcr(PLB1_ACR) & ~PLB1_ACR_PPM_MASK) | PLB1_ACR_PPM_FAIR;
+ addr = (addr & ~PLB1_ACR_HBU_MASK) | PLB1_ACR_HBU_ENABLED;
+ addr = (addr & ~PLB1_ACR_RDP_MASK) | PLB1_ACR_RDP_4DEEP;
+ addr = (addr & ~PLB1_ACR_WRP_MASK) | PLB1_ACR_WRP_2DEEP;
+ mtdcr(PLB1_ACR, addr);
return 1;
}
diff --git a/board/esd/hh405/flash.c b/board/esd/hh405/flash.c
index 274ada9..a53122b 100644
--- a/board/esd/hh405/flash.c
+++ b/board/esd/hh405/flash.c
@@ -65,9 +65,9 @@
flash_get_offsets (-size_b0, &flash_info[0]);
/* Re-do sizing to get full correct info */
- mtdcr(ebccfga, pb0cr);
- pbcr = mfdcr(ebccfgd);
- mtdcr(ebccfga, pb0cr);
+ mtdcr(EBC0_CFGADDR, PB0CR);
+ pbcr = mfdcr(EBC0_CFGDATA);
+ mtdcr(EBC0_CFGADDR, PB0CR);
base_b0 = -size_b0;
switch (size_b0) {
case 1 << 20:
@@ -87,7 +87,7 @@
break;
}
pbcr = (pbcr & 0x0001ffff) | base_b0 | (size_val << 17);
- mtdcr(ebccfgd, pbcr);
+ mtdcr(EBC0_CFGDATA, pbcr);
/* Monitor protection ON by default */
(void)flash_protect(FLAG_PROTECT_SET,
diff --git a/board/esd/hh405/hh405.c b/board/esd/hh405/hh405.c
index 5ae4c75..b72b716 100644
--- a/board/esd/hh405/hh405.c
+++ b/board/esd/hh405/hh405.c
@@ -374,7 +374,7 @@
/*
* EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us
*/
- mtebc(epcr, 0xa8400000); /* ebc always driven */
+ mtebc(EBC0_CFG, 0xa8400000); /* ebc always driven */
return 0;
}
diff --git a/board/esd/hub405/flash.c b/board/esd/hub405/flash.c
index 274ada9..a53122b 100644
--- a/board/esd/hub405/flash.c
+++ b/board/esd/hub405/flash.c
@@ -65,9 +65,9 @@
flash_get_offsets (-size_b0, &flash_info[0]);
/* Re-do sizing to get full correct info */
- mtdcr(ebccfga, pb0cr);
- pbcr = mfdcr(ebccfgd);
- mtdcr(ebccfga, pb0cr);
+ mtdcr(EBC0_CFGADDR, PB0CR);
+ pbcr = mfdcr(EBC0_CFGDATA);
+ mtdcr(EBC0_CFGADDR, PB0CR);
base_b0 = -size_b0;
switch (size_b0) {
case 1 << 20:
@@ -87,7 +87,7 @@
break;
}
pbcr = (pbcr & 0x0001ffff) | base_b0 | (size_val << 17);
- mtdcr(ebccfgd, pbcr);
+ mtdcr(EBC0_CFGDATA, pbcr);
/* Monitor protection ON by default */
(void)flash_protect(FLAG_PROTECT_SET,
diff --git a/board/esd/hub405/hub405.c b/board/esd/hub405/hub405.c
index 03e5ad7..acb23da 100644
--- a/board/esd/hub405/hub405.c
+++ b/board/esd/hub405/hub405.c
@@ -97,7 +97,7 @@
/*
* EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us
*/
- mtebc (epcr, 0xa8400000); /* ebc always driven */
+ mtebc (EBC0_CFG, 0xa8400000); /* ebc always driven */
return 0;
}
diff --git a/board/esd/ocrtc/flash.c b/board/esd/ocrtc/flash.c
index e763a89..eda7c57 100644
--- a/board/esd/ocrtc/flash.c
+++ b/board/esd/ocrtc/flash.c
@@ -68,9 +68,9 @@
/* Re-do sizing to get full correct info */
if (size_b1) {
- mtdcr (ebccfga, pb0cr);
- pbcr = mfdcr (ebccfgd);
- mtdcr (ebccfga, pb0cr);
+ mtdcr (EBC0_CFGADDR, PB0CR);
+ pbcr = mfdcr (EBC0_CFGDATA);
+ mtdcr (EBC0_CFGADDR, PB0CR);
base_b1 = -size_b1;
switch (size_b1) {
case 1 << 20:
@@ -90,14 +90,14 @@
break;
}
pbcr = (pbcr & 0x0001ffff) | base_b1 | (size_val << 17);
- mtdcr (ebccfgd, pbcr);
- /* printf("pb1cr = %x\n", pbcr); */
+ mtdcr (EBC0_CFGDATA, pbcr);
+ /* printf("PB1CR = %x\n", pbcr); */
}
if (size_b0) {
- mtdcr (ebccfga, pb1cr);
- pbcr = mfdcr (ebccfgd);
- mtdcr (ebccfga, pb1cr);
+ mtdcr (EBC0_CFGADDR, PB1CR);
+ pbcr = mfdcr (EBC0_CFGDATA);
+ mtdcr (EBC0_CFGADDR, PB1CR);
base_b0 = base_b1 - size_b0;
switch (size_b1) {
case 1 << 20:
@@ -117,8 +117,8 @@
break;
}
pbcr = (pbcr & 0x0001ffff) | base_b0 | (size_val << 17);
- mtdcr (ebccfgd, pbcr);
- /* printf("pb0cr = %x\n", pbcr); */
+ mtdcr (EBC0_CFGDATA, pbcr);
+ /* printf("PB0CR = %x\n", pbcr); */
}
size_b0 = flash_get_size ((vu_long *) base_b0, &flash_info[0]);
diff --git a/board/esd/ocrtc/ocrtc.c b/board/esd/ocrtc/ocrtc.c
index 35bfa95..709bcdd 100644
--- a/board/esd/ocrtc/ocrtc.c
+++ b/board/esd/ocrtc/ocrtc.c
@@ -57,7 +57,7 @@
* EBC Configuration Register: clear EBTC -> high-Z ebc signals between
* transfers, set device-paced timeout to 256 cycles
*/
- mtebc (epcr, 0x20400000);
+ mtebc (EBC0_CFG, 0x20400000);
return 0;
}
diff --git a/board/esd/pci405/flash.c b/board/esd/pci405/flash.c
index 9058483..67a7bb5 100644
--- a/board/esd/pci405/flash.c
+++ b/board/esd/pci405/flash.c
@@ -65,9 +65,9 @@
flash_get_offsets (-size_b0, &flash_info[0]);
/* Re-do sizing to get full correct info */
- mtdcr(ebccfga, pb0cr);
- pbcr = mfdcr(ebccfgd);
- mtdcr(ebccfga, pb0cr);
+ mtdcr(EBC0_CFGADDR, PB0CR);
+ pbcr = mfdcr(EBC0_CFGDATA);
+ mtdcr(EBC0_CFGADDR, PB0CR);
base_b0 = -size_b0;
switch (size_b0) {
case 1 << 20:
@@ -87,7 +87,7 @@
break;
}
pbcr = (pbcr & 0x0001ffff) | base_b0 | (size_val << 17);
- mtdcr(ebccfgd, pbcr);
+ mtdcr(EBC0_CFGDATA, pbcr);
/* Monitor protection ON by default */
(void)flash_protect(FLAG_PROTECT_SET,
diff --git a/board/esd/pci405/pci405.c b/board/esd/pci405/pci405.c
index 56184ca..04bc569 100644
--- a/board/esd/pci405/pci405.c
+++ b/board/esd/pci405/pci405.c
@@ -67,7 +67,7 @@
int board_revision(void)
{
- unsigned long cntrl0Reg;
+ unsigned long CPC0_CR0Reg;
unsigned long value;
/*
@@ -77,8 +77,8 @@
/*
* Setup GPIO pins (CS2/GPIO11 and CS3/GPIO12 as GPIO)
*/
- cntrl0Reg = mfdcr(cntrl0);
- mtdcr(cntrl0, cntrl0Reg | 0x03000000);
+ CPC0_CR0Reg = mfdcr(CPC0_CR0);
+ mtdcr(CPC0_CR0, CPC0_CR0Reg | 0x03000000);
out_be32((void*)GPIO0_ODR, in_be32((void*)GPIO0_ODR) & ~0x00100200);
out_be32((void*)GPIO0_TCR, in_be32((void*)GPIO0_TCR) & ~0x00100200);
udelay(1000); /* wait some time before reading input */
@@ -87,7 +87,7 @@
/*
* Restore GPIO settings
*/
- mtdcr(cntrl0, cntrl0Reg);
+ mtdcr(CPC0_CR0, CPC0_CR0Reg);
switch (value) {
case 0x00100200:
@@ -133,7 +133,7 @@
int board_early_init_f (void)
{
- unsigned long cntrl0Reg;
+ unsigned long CPC0_CR0Reg;
/*
* First pull fpga-prg pin low, to disable fpga logic (on version 1.2 board)
@@ -166,18 +166,18 @@
/*
* Setup GPIO pins (IRQ4/GPIO21 as GPIO)
*/
- cntrl0Reg = mfdcr(cntrl0);
- mtdcr(cntrl0, cntrl0Reg | 0x00008000);
+ CPC0_CR0Reg = mfdcr(CPC0_CR0);
+ mtdcr(CPC0_CR0, CPC0_CR0Reg | 0x00008000);
/*
* Setup GPIO pins (CS6+CS7 as GPIO)
*/
- mtdcr(cntrl0, cntrl0Reg | 0x00300000);
+ mtdcr(CPC0_CR0, CPC0_CR0Reg | 0x00300000);
/*
* EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 25 us
*/
- mtebc (epcr, 0xa8400000); /* ebc always driven */
+ mtebc (EBC0_CFG, 0xa8400000); /* ebc always driven */
return 0;
}
@@ -282,11 +282,11 @@
#define PCI0_BRDGOPT1 0x4a
pci_write_config_word(PCIDEVID_405GP, PCI0_BRDGOPT1, 0x3f20);
-#define plb0_acr 0x87
+#define PLB0_ACR 0x87
/*
* Enable fairness and high bus utilization
*/
- mtdcr(plb0_acr, 0x98000000);
+ mtdcr(PLB0_ACR, 0x98000000);
free(dst);
return (0);
@@ -313,14 +313,14 @@
printf(" (Rev 1.%ld", gd->board_type);
if (gd->board_type >= 2) {
- unsigned long cntrl0Reg;
+ unsigned long CPC0_CR0Reg;
unsigned long value;
/*
* Setup GPIO pins (Trace/GPIO1 to GPIO)
*/
- cntrl0Reg = mfdcr(cntrl0);
- mtdcr(cntrl0, cntrl0Reg & ~0x08000000);
+ CPC0_CR0Reg = mfdcr(CPC0_CR0);
+ mtdcr(CPC0_CR0, CPC0_CR0Reg & ~0x08000000);
out_be32((void*)GPIO0_ODR, in_be32((void*)GPIO0_ODR) & ~0x40000000);
out_be32((void*)GPIO0_TCR, in_be32((void*)GPIO0_TCR) & ~0x40000000);
udelay(1000); /* wait some time before reading input */
diff --git a/board/esd/plu405/flash.c b/board/esd/plu405/flash.c
index 274ada9..a53122b 100644
--- a/board/esd/plu405/flash.c
+++ b/board/esd/plu405/flash.c
@@ -65,9 +65,9 @@
flash_get_offsets (-size_b0, &flash_info[0]);
/* Re-do sizing to get full correct info */
- mtdcr(ebccfga, pb0cr);
- pbcr = mfdcr(ebccfgd);
- mtdcr(ebccfga, pb0cr);
+ mtdcr(EBC0_CFGADDR, PB0CR);
+ pbcr = mfdcr(EBC0_CFGDATA);
+ mtdcr(EBC0_CFGADDR, PB0CR);
base_b0 = -size_b0;
switch (size_b0) {
case 1 << 20:
@@ -87,7 +87,7 @@
break;
}
pbcr = (pbcr & 0x0001ffff) | base_b0 | (size_val << 17);
- mtdcr(ebccfgd, pbcr);
+ mtdcr(EBC0_CFGDATA, pbcr);
/* Monitor protection ON by default */
(void)flash_protect(FLAG_PROTECT_SET,
diff --git a/board/esd/plu405/plu405.c b/board/esd/plu405/plu405.c
index e41545a..a3c1cec 100644
--- a/board/esd/plu405/plu405.c
+++ b/board/esd/plu405/plu405.c
@@ -90,7 +90,7 @@
* EBC Configuration Register: set ready timeout to
* 512 ebc-clks -> ca. 15 us
*/
- mtebc(epcr, 0xa8400000); /* ebc always driven */
+ mtebc(EBC0_CFG, 0xa8400000); /* ebc always driven */
return 0;
}
diff --git a/board/esd/pmc405/pmc405.c b/board/esd/pmc405/pmc405.c
index 192a642..5ff87e7 100644
--- a/board/esd/pmc405/pmc405.c
+++ b/board/esd/pmc405/pmc405.c
@@ -60,12 +60,12 @@
* EBC Configuration Register:
* set ready timeout to 512 ebc-clks -> ca. 15 us
*/
- mtebc (epcr, 0xa8400000);
+ mtebc (EBC0_CFG, 0xa8400000);
/*
* Setup GPIO pins
*/
- mtdcr(cntrl0, mfdcr(cntrl0) | ((CONFIG_SYS_FPGA_INIT |
+ mtdcr(CPC0_CR0, mfdcr(CPC0_CR0) | ((CONFIG_SYS_FPGA_INIT |
CONFIG_SYS_FPGA_DONE |
CONFIG_SYS_XEREADY |
CONFIG_SYS_NONMONARCH |
@@ -73,7 +73,7 @@
if (!(in_be32((void *)GPIO0_IR) & CONFIG_SYS_REV1_2)) {
/* rev 1.2 boards */
- mtdcr(cntrl0, mfdcr(cntrl0) | ((CONFIG_SYS_INTA_FAKE |
+ mtdcr(CPC0_CR0, mfdcr(CPC0_CR0) | ((CONFIG_SYS_INTA_FAKE |
CONFIG_SYS_SELF_RST) << 5));
}
diff --git a/board/esd/pmc405de/pmc405de.c b/board/esd/pmc405de/pmc405de.c
index f68e1b5..419311a 100644
--- a/board/esd/pmc405de/pmc405de.c
+++ b/board/esd/pmc405de/pmc405de.c
@@ -127,7 +127,7 @@
* - set ready timeout to 512 ebc-clks -> ca. 15 us
* - EBC lines are always driven
*/
- mtebc(epcr, 0xa8400000);
+ mtebc(EBC0_CFG, 0xa8400000);
return 0;
}
diff --git a/board/esd/pmc440/pmc440.c b/board/esd/pmc440/pmc440.c
index f22a1c2..119cbf2 100644
--- a/board/esd/pmc440/pmc440.c
+++ b/board/esd/pmc440/pmc440.c
@@ -64,7 +64,7 @@
* Use default console on P4 when strapping jumper
* is installed (bootstrap option != 'H').
*/
- mfsdr(SDR_PINSTP, val);
+ mfsdr(SDR0_PINSTP, val);
if (((val & 0xf0000000) >> 29) != 7)
return &serial1_device;
@@ -100,8 +100,8 @@
u32 reg;
/* general EBC configuration (disable EBC timeouts) */
- mtdcr(ebccfga, xbcfg);
- mtdcr(ebccfgd, 0xf8400000);
+ mtdcr(EBC0_CFGADDR, EBC0_CFG);
+ mtdcr(EBC0_CFGDATA, 0xf8400000);
/*
* Setup the GPIO pins
@@ -134,13 +134,13 @@
out_be32((void *)GPIO1_ISR3H, 0x00000000);
/* patch PLB:PCI divider for 66MHz PCI */
- mfcpr(clk_spcid, reg);
+ mfcpr(CPR0_SPCID, reg);
if (pci_is_66mhz() && (reg != 0x02000000)) {
- mtcpr(clk_spcid, 0x02000000); /* 133MHZ : 2 for 66MHz PCI */
+ mtcpr(CPR0_SPCID, 0x02000000); /* 133MHZ : 2 for 66MHz PCI */
- mfcpr(clk_icfg, reg);
+ mfcpr(CPR0_ICFG, reg);
reg |= CPR0_ICFG_RLI_MASK;
- mtcpr(clk_icfg, reg);
+ mtcpr(CPR0_ICFG, reg);
mtspr(SPRN_DBCR0, 0x20000000); /* do chip reset */
}
@@ -240,19 +240,19 @@
gd->bd->bi_flashoffset = 0;
#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
- mtdcr(ebccfga, pb2cr);
+ mtdcr(EBC0_CFGADDR, PB2CR);
#else
- mtdcr(ebccfga, pb0cr);
+ mtdcr(EBC0_CFGADDR, PB0CR);
#endif
- pbcr = mfdcr(ebccfgd);
+ pbcr = mfdcr(EBC0_CFGDATA);
size_val = ffs(gd->bd->bi_flashsize) - 21;
pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SPL)
- mtdcr(ebccfga, pb2cr);
+ mtdcr(EBC0_CFGADDR, PB2CR);
#else
- mtdcr(ebccfga, pb0cr);
+ mtdcr(EBC0_CFGADDR, PB0CR);
#endif
- mtdcr(ebccfgd, pbcr);
+ mtdcr(EBC0_CFGDATA, pbcr);
/*
* Re-check to get correct base address
@@ -424,8 +424,8 @@
* This fix will make the MAL burst disabling patch for the Linux
* EMAC driver obsolete.
*/
- reg = mfdcr(plb4_acr) & ~PLB4_ACR_WRP;
- mtdcr(plb4_acr, reg);
+ reg = mfdcr(PLB4_ACR) & ~PLB4_ACR_WRP;
+ mtdcr(PLB4_ACR, reg);
#ifdef CONFIG_FPGA
pmc440_init_fpga();
@@ -507,35 +507,35 @@
* Set priority for all PLB3 devices to 0.
* Set PLB3 arbiter to fair mode.
*/
- mfsdr(sdr_amp1, addr);
- mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(plb3_acr);
- mtdcr(plb3_acr, addr | 0x80000000);
+ mfsdr(SD0_AMP1, addr);
+ mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
+ addr = mfdcr(PLB3_ACR);
+ mtdcr(PLB3_ACR, addr | 0x80000000);
/*
* Set priority for all PLB4 devices to 0.
*/
- mfsdr(sdr_amp0, addr);
- mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(plb4_acr) | 0xa0000000; /* Was 0x8---- */
- mtdcr(plb4_acr, addr);
+ mfsdr(SD0_AMP0, addr);
+ mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
+ addr = mfdcr(PLB4_ACR) | 0xa0000000; /* Was 0x8---- */
+ mtdcr(PLB4_ACR, addr);
/*
* Set Nebula PLB4 arbiter to fair mode.
*/
/* Segment0 */
- addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair;
- addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled;
- addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep;
- addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep;
- mtdcr(plb0_acr, addr);
+ addr = (mfdcr(PLB0_ACR) & ~PLB0_ACR_PPM_MASK) | PLB0_ACR_PPM_FAIR;
+ addr = (addr & ~PLB0_ACR_HBU_MASK) | PLB0_ACR_HBU_ENABLED;
+ addr = (addr & ~PLB0_ACR_RDP_MASK) | PLB0_ACR_RDP_4DEEP;
+ addr = (addr & ~PLB0_ACR_WRP_MASK) | PLB0_ACR_WRP_2DEEP;
+ mtdcr(PLB0_ACR, addr);
/* Segment1 */
- addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair;
- addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled;
- addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep;
- addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep;
- mtdcr(plb1_acr, addr);
+ addr = (mfdcr(PLB1_ACR) & ~PLB1_ACR_PPM_MASK) | PLB1_ACR_PPM_FAIR;
+ addr = (addr & ~PLB1_ACR_HBU_MASK) | PLB1_ACR_HBU_ENABLED;
+ addr = (addr & ~PLB1_ACR_RDP_MASK) | PLB1_ACR_RDP_4DEEP;
+ addr = (addr & ~PLB1_ACR_WRP_MASK) | PLB1_ACR_WRP_2DEEP;
+ mtdcr(PLB1_ACR, addr);
#ifdef CONFIG_PCI_PNP
hose->fixup_irq = pmc440_pci_fixup_irq;
diff --git a/board/esd/voh405/flash.c b/board/esd/voh405/flash.c
index 274ada9..a53122b 100644
--- a/board/esd/voh405/flash.c
+++ b/board/esd/voh405/flash.c
@@ -65,9 +65,9 @@
flash_get_offsets (-size_b0, &flash_info[0]);
/* Re-do sizing to get full correct info */
- mtdcr(ebccfga, pb0cr);
- pbcr = mfdcr(ebccfgd);
- mtdcr(ebccfga, pb0cr);
+ mtdcr(EBC0_CFGADDR, PB0CR);
+ pbcr = mfdcr(EBC0_CFGDATA);
+ mtdcr(EBC0_CFGADDR, PB0CR);
base_b0 = -size_b0;
switch (size_b0) {
case 1 << 20:
@@ -87,7 +87,7 @@
break;
}
pbcr = (pbcr & 0x0001ffff) | base_b0 | (size_val << 17);
- mtdcr(ebccfgd, pbcr);
+ mtdcr(EBC0_CFGDATA, pbcr);
/* Monitor protection ON by default */
(void)flash_protect(FLAG_PROTECT_SET,
diff --git a/board/esd/voh405/voh405.c b/board/esd/voh405/voh405.c
index 9127550..7477f56 100644
--- a/board/esd/voh405/voh405.c
+++ b/board/esd/voh405/voh405.c
@@ -99,7 +99,7 @@
/*
* EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us
*/
- mtebc (epcr, 0xa8400000); /* ebc always driven */
+ mtebc (EBC0_CFG, 0xa8400000); /* ebc always driven */
return 0;
}
diff --git a/board/esd/vom405/flash.c b/board/esd/vom405/flash.c
index 274ada9..a53122b 100644
--- a/board/esd/vom405/flash.c
+++ b/board/esd/vom405/flash.c
@@ -65,9 +65,9 @@
flash_get_offsets (-size_b0, &flash_info[0]);
/* Re-do sizing to get full correct info */
- mtdcr(ebccfga, pb0cr);
- pbcr = mfdcr(ebccfgd);
- mtdcr(ebccfga, pb0cr);
+ mtdcr(EBC0_CFGADDR, PB0CR);
+ pbcr = mfdcr(EBC0_CFGDATA);
+ mtdcr(EBC0_CFGADDR, PB0CR);
base_b0 = -size_b0;
switch (size_b0) {
case 1 << 20:
@@ -87,7 +87,7 @@
break;
}
pbcr = (pbcr & 0x0001ffff) | base_b0 | (size_val << 17);
- mtdcr(ebccfgd, pbcr);
+ mtdcr(EBC0_CFGDATA, pbcr);
/* Monitor protection ON by default */
(void)flash_protect(FLAG_PROTECT_SET,
diff --git a/board/esd/vom405/vom405.c b/board/esd/vom405/vom405.c
index a481aca..de9c7b9 100644
--- a/board/esd/vom405/vom405.c
+++ b/board/esd/vom405/vom405.c
@@ -56,7 +56,7 @@
/*
* EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us
*/
- mtebc (epcr, 0xa8400000); /* ebc always driven */
+ mtebc (EBC0_CFG, 0xa8400000); /* ebc always driven */
/*
* Reset CPLD via GPIO12 (CS3) pin
diff --git a/board/esd/wuh405/flash.c b/board/esd/wuh405/flash.c
index 274ada9..a53122b 100644
--- a/board/esd/wuh405/flash.c
+++ b/board/esd/wuh405/flash.c
@@ -65,9 +65,9 @@
flash_get_offsets (-size_b0, &flash_info[0]);
/* Re-do sizing to get full correct info */
- mtdcr(ebccfga, pb0cr);
- pbcr = mfdcr(ebccfgd);
- mtdcr(ebccfga, pb0cr);
+ mtdcr(EBC0_CFGADDR, PB0CR);
+ pbcr = mfdcr(EBC0_CFGDATA);
+ mtdcr(EBC0_CFGADDR, PB0CR);
base_b0 = -size_b0;
switch (size_b0) {
case 1 << 20:
@@ -87,7 +87,7 @@
break;
}
pbcr = (pbcr & 0x0001ffff) | base_b0 | (size_val << 17);
- mtdcr(ebccfgd, pbcr);
+ mtdcr(EBC0_CFGDATA, pbcr);
/* Monitor protection ON by default */
(void)flash_protect(FLAG_PROTECT_SET,
diff --git a/board/esd/wuh405/wuh405.c b/board/esd/wuh405/wuh405.c
index e330fff..e86f1d0 100644
--- a/board/esd/wuh405/wuh405.c
+++ b/board/esd/wuh405/wuh405.c
@@ -75,7 +75,7 @@
/*
* EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us
*/
- mtebc (epcr, 0xa8400000); /* ebc always driven */
+ mtebc (EBC0_CFG, 0xa8400000); /* ebc always driven */
return 0;
}
diff --git a/board/exbitgen/exbitgen.c b/board/exbitgen/exbitgen.c
index dc07d3d..0f84127 100644
--- a/board/exbitgen/exbitgen.c
+++ b/board/exbitgen/exbitgen.c
@@ -94,29 +94,29 @@
tot_size = 0;
- mtdcr (memcfga, mem_mb0cf);
- tmp = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
+ tmp = mfdcr (SDRAM0_CFGDATA);
if (tmp & 0x00000001) {
bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
tot_size += bank_size;
}
- mtdcr (memcfga, mem_mb1cf);
- tmp = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_mb1cf);
+ tmp = mfdcr (SDRAM0_CFGDATA);
if (tmp & 0x00000001) {
bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
tot_size += bank_size;
}
- mtdcr (memcfga, mem_mb2cf);
- tmp = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_mb2cf);
+ tmp = mfdcr (SDRAM0_CFGDATA);
if (tmp & 0x00000001) {
bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
tot_size += bank_size;
}
- mtdcr (memcfga, mem_mb3cf);
- tmp = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_mb3cf);
+ tmp = mfdcr (SDRAM0_CFGDATA);
if (tmp & 0x00000001) {
bank_size = 0x00400000 << ((tmp >> 17) & 0x7);
tot_size += bank_size;
diff --git a/board/exbitgen/init.S b/board/exbitgen/init.S
index cb54874..c2dae56 100644
--- a/board/exbitgen/init.S
+++ b/board/exbitgen/init.S
@@ -109,10 +109,10 @@
#define WDCR_EBC(reg,val) addi r4,0,reg;\
- mtdcr ebccfga,r4;\
+ mtdcr EBC0_CFGADDR,r4;\
addis r4,0,val@h;\
ori r4,r4,val@l;\
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
/*---------------------------------------------------------------------
* Function: ext_bus_cntlr_init
@@ -164,22 +164,22 @@
* Memory Bank 0 (Boot Flash) initialization
*---------------------------------------------------------------
*/
- WDCR_EBC(pb0ap, FLASH_32bit_AP)
- WDCR_EBC(pb0cr, 0xffe38000)
-/*pnc WDCR_EBC(pb0cr, FLASH_32bit_CR) */
+ WDCR_EBC(PB1AP, FLASH_32bit_AP)
+ WDCR_EBC(PB0CR, 0xffe38000)
+/*pnc WDCR_EBC(PB0CR, FLASH_32bit_CR) */
/*---------------------------------------------------------------
* Memory Bank 5 (CPLD) initialization
*---------------------------------------------------------------
*/
- WDCR_EBC(pb5ap, 0x01010040)
-/*jsa recommendation: WDCR_EBC(pb5ap, 0x00010040) */
- WDCR_EBC(pb5cr, 0x10038000)
+ WDCR_EBC(PB5AP, 0x01010040)
+/*jsa recommendation: WDCR_EBC(PB5AP, 0x00010040) */
+ WDCR_EBC(PB5CR, 0x10038000)
/*--------------------------------------------------------------- */
/* Memory Bank 6 (not used) initialization */
/*--------------------------------------------------------------- */
- WDCR_EBC(pb6cr, 0x00000000)
+ WDCR_EBC(PB6CR, 0x00000000)
/* Read HW ID to determine whether old H2 board or new generic CPU board */
addis r3, 0, HW_ID_ADDR@h
@@ -196,24 +196,24 @@
/*--------------------------------------------------------------- */
/* Memory Bank 1 (Application Flash) initialization for generic CPU board */
/*--------------------------------------------------------------- */
-/* WDCR_EBC(pb1ap, 0x7b015480) /###* T.B.M. */
-/* WDCR_EBC(pb1ap, 0x7F8FFE80) /###* T.B.M. */
- WDCR_EBC(pb1ap, 0x9b015480) /* hlb-20020207: burst 8 bit 6 cycles */
+/* WDCR_EBC(PB1AP, 0x7b015480) /###* T.B.M. */
+/* WDCR_EBC(PB1AP, 0x7F8FFE80) /###* T.B.M. */
+ WDCR_EBC(PB1AP, 0x9b015480) /* hlb-20020207: burst 8 bit 6 cycles */
-/* WDCR_EBC(pb1cr, 0x20098000) /###* 16 MB */
- WDCR_EBC(pb1cr, 0x200B8000) /* 32 MB */
+/* WDCR_EBC(PB1CR, 0x20098000) /###* 16 MB */
+ WDCR_EBC(PB1CR, 0x200B8000) /* 32 MB */
/*--------------------------------------------------------------- */
/* Memory Bank 4 (Onboard FPGA) initialization for generic CPU board */
/*--------------------------------------------------------------- */
- WDCR_EBC(pb4ap, 0x01010000) /* */
- WDCR_EBC(pb4cr, 0x1021c000) /* */
+ WDCR_EBC(PB4AP, 0x01010000) /* */
+ WDCR_EBC(PB4CR, 0x1021c000) /* */
/*--------------------------------------------------------------- */
/* Memory Bank 7 (Heathrow chip on Reference board) initialization */
/*--------------------------------------------------------------- */
- WDCR_EBC(pb7ap, 0x200ffe80) /* No Ready, many wait states (let reflections die out) */
- WDCR_EBC(pb7cr, 0X4001A000)
+ WDCR_EBC(PB7AP, 0x200ffe80) /* No Ready, many wait states (let reflections die out) */
+ WDCR_EBC(PB7CR, 0X4001A000)
bl setup_continue
@@ -222,36 +222,36 @@
/*--------------------------------------------------------------- */
/* Memory Bank 1 (Application Flash) initialization */
/*--------------------------------------------------------------- */
- WDCR_EBC(pb1ap, 0x7b015480) /* T.B.M. */
-/*3010 WDCR_EBC(pb1ap, 0x7F8FFE80) /###* T.B.M. */
- WDCR_EBC(pb1cr, 0x20058000)
+ WDCR_EBC(PB1AP, 0x7b015480) /* T.B.M. */
+/*3010 WDCR_EBC(PB1AP, 0x7F8FFE80) /###* T.B.M. */
+ WDCR_EBC(PB1CR, 0x20058000)
/*--------------------------------------------------------------- */
/* Memory Bank 2 (Application Flash) initialization */
/*--------------------------------------------------------------- */
- WDCR_EBC(pb2ap, 0x7b015480) /* T.B.M. */
-/*3010 WDCR_EBC(pb2ap, 0x7F8FFE80) /###* T.B.M. */
- WDCR_EBC(pb2cr, 0x20458000)
+ WDCR_EBC(PB2AP, 0x7b015480) /* T.B.M. */
+/*3010 WDCR_EBC(PB2AP, 0x7F8FFE80) /###* T.B.M. */
+ WDCR_EBC(PB2CR, 0x20458000)
/*--------------------------------------------------------------- */
/* Memory Bank 3 (Application Flash) initialization */
/*--------------------------------------------------------------- */
- WDCR_EBC(pb3ap, 0x7b015480) /* T.B.M. */
-/*3010 WDCR_EBC(pb3ap, 0x7F8FFE80) /###* T.B.M. */
- WDCR_EBC(pb3cr, 0x20858000)
+ WDCR_EBC(PB3AP, 0x7b015480) /* T.B.M. */
+/*3010 WDCR_EBC(PB3AP, 0x7F8FFE80) /###* T.B.M. */
+ WDCR_EBC(PB3CR, 0x20858000)
/*--------------------------------------------------------------- */
/* Memory Bank 4 (Application Flash) initialization */
/*--------------------------------------------------------------- */
- WDCR_EBC(pb4ap, 0x7b015480) /* T.B.M. */
-/*3010 WDCR_EBC(pb4ap, 0x7F8FFE80) /###* T.B.M. */
- WDCR_EBC(pb4cr, 0x20C58000)
+ WDCR_EBC(PB4AP, 0x7b015480) /* T.B.M. */
+/*3010 WDCR_EBC(PB4AP, 0x7F8FFE80) /###* T.B.M. */
+ WDCR_EBC(PB4CR, 0x20C58000)
/*--------------------------------------------------------------- */
/* Memory Bank 7 (Heathrow chip) initialization */
/*--------------------------------------------------------------- */
- WDCR_EBC(pb7ap, 0x02000280) /* No Ready, 4 wait states */
- WDCR_EBC(pb7cr, 0X4001A000)
+ WDCR_EBC(PB7AP, 0x02000280) /* No Ready, 4 wait states */
+ WDCR_EBC(PB7CR, 0X4001A000)
setup_continue:
@@ -294,7 +294,7 @@
/* Read PLL feedback divider and calculate clock period of local bus in */
/* granularity of 10 ps. Save clock period in r30 */
/*-------------------------------------------------------------- */
- mfdcr r4, pllmd
+ mfdcr r4, CPC0_PLLMR
addi r9, 0, 25
srw r4, r4, r9
andi. r4, r4, 0x07
@@ -383,8 +383,8 @@
/* Set SDTR1 */
/*----------------------------------------------------------- */
addi r5,0,mem_sdtr1
- mtdcr memcfga,r5
- mtdcr memcfgd,r4
+ mtdcr SDRAM0_CFGADDR,r5
+ mtdcr SDRAM0_CFGDATA,r4
/*----------------------------------------------------------- */
/* */
@@ -414,8 +414,8 @@
/* Set SDRAM bank 0 register and adjust r6 for next bank */
/*------------------------------------------------------ */
addi r7,0,mem_mb0cf
- mtdcr memcfga,r7
- mtdcr memcfgd,r6
+ mtdcr SDRAM0_CFGADDR,r7
+ mtdcr SDRAM0_CFGDATA,r6
add r6, r6, r15 /* add bank size to base address for next bank */
@@ -425,16 +425,16 @@
bne b1skip
addi r7,0,mem_mb1cf
- mtdcr memcfga,r7
- mtdcr memcfgd,r6
+ mtdcr SDRAM0_CFGADDR,r7
+ mtdcr SDRAM0_CFGDATA,r6
add r6, r6, r15 /* add bank size to base address for next bank */
/* Set SDRAM bank 2 register and adjust r6 for next bank */
/*------------------------------------------------------ */
b1skip: addi r7,0,mem_mb2cf
- mtdcr memcfga,r7
- mtdcr memcfgd,r6
+ mtdcr SDRAM0_CFGADDR,r7
+ mtdcr SDRAM0_CFGDATA,r6
add r6, r6, r15 /* add bank size to base address for next bank */
@@ -444,8 +444,8 @@
bne b3skip
addi r7,0,mem_mb3cf
- mtdcr memcfga,r7
- mtdcr memcfgd,r6
+ mtdcr SDRAM0_CFGADDR,r7
+ mtdcr SDRAM0_CFGDATA,r6
b3skip:
/*----------------------------------------------------------- */
@@ -457,8 +457,8 @@
bl rtr_2
rtr_1: addis r7, 0, 0x03F8
rtr_2: addi r4,0,mem_rtr
- mtdcr memcfga,r4
- mtdcr memcfgd,r7
+ mtdcr SDRAM0_CFGADDR,r4
+ mtdcr SDRAM0_CFGDATA,r7
/*----------------------------------------------------------- */
/* Delay to ensure 200usec have elapsed since reset. Assume worst */
@@ -477,10 +477,10 @@
/* read/prefetch. */
/*----------------------------------------------------------- */
addi r4,0,mem_mcopt1
- mtdcr memcfga,r4
+ mtdcr SDRAM0_CFGADDR,r4
addis r4,0,0x80C0 /* set DC_EN=1 */
ori r4,r4,0x0000
- mtdcr memcfgd,r4
+ mtdcr SDRAM0_CFGDATA,r4
/*----------------------------------------------------------- */
@@ -980,9 +980,9 @@
/* For CPLD */
/* 0 + 00000 + 010 + 000 + 00 + 01 + 00 + 00 + 000 + 0 + 0 + 1 + 0 + 00000 */
-/* WDCR_EBC(pb5ap, 0x01010040) */
-/*jsa recommendation: WDCR_EBC(pb5ap, 0x00010040) */
-/* WDCR_EBC(pb5cr, 0X10018000) */
+/* WDCR_EBC(PB5AP, 0x01010040) */
+/*jsa recommendation: WDCR_EBC(PB5AP, 0x00010040) */
+/* WDCR_EBC(PB5CR, 0X10018000) */
/* Access parms */
/* 100 3 8 0 0 0 */
/* 0x100 + 001 + 11 + 00 + 0 0000 0000 0000 = 0x10038000 */
@@ -1003,9 +1003,9 @@
/* Usage: read/write */
/* Width: 32 bit */
-/* Walnut fpga pb7ap */
+/* Walnut fpga PB7AP */
/* 0 1 8 1 5 2 8 0 */
/* 0 + 00000 + 011 + 000 + 00 + 01 + 01 + 01 + 001 + 0 + 1 + 0 + 0 + 00000 */
-/* Walnut fpga pb7cr */
+/* Walnut fpga PB7CR */
/* 0xF0318000 */
/* */
diff --git a/board/g2000/g2000.c b/board/g2000/g2000.c
index f6f4719..ae258e1 100644
--- a/board/g2000/g2000.c
+++ b/board/g2000/g2000.c
@@ -58,7 +58,7 @@
/*
* EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us
*/
- mtebc (epcr, 0xa8400000); /* ebc always driven */
+ mtebc (EBC0_CFG, 0xa8400000); /* ebc always driven */
#endif
return 0;
@@ -114,7 +114,7 @@
long int init_sdram_static_settings(void)
{
-#define mtsdram0(reg, data) mtdcr(memcfga,reg);mtdcr(memcfgd,data)
+#define mtsdram0(reg, data) mtdcr(SDRAM0_CFGADDR,reg);mtdcr(SDRAM0_CFGDATA,data)
/* disable memcontroller so updates work */
mtsdram0( mem_mcopt1, MEM_MCOPT1_INIT_VAL );
mtsdram0( mem_rtr , MEM_RTR_INIT_VAL );
@@ -154,15 +154,15 @@
ulong ap, cr;
printf("\nEBC registers for PPC405GP:\n");
- mfebc(pb0ap, ap); mfebc(pb0cr, cr);
+ mfebc(PB0AP, ap); mfebc(PB0CR, cr);
printf("0: AP=%08lx CP=%08lx\n", ap, cr);
- mfebc(pb1ap, ap); mfebc(pb1cr, cr);
+ mfebc(PB1AP, ap); mfebc(PB1CR, cr);
printf("1: AP=%08lx CP=%08lx\n", ap, cr);
- mfebc(pb2ap, ap); mfebc(pb2cr, cr);
+ mfebc(PB2AP, ap); mfebc(PB2CR, cr);
printf("2: AP=%08lx CP=%08lx\n", ap, cr);
- mfebc(pb3ap, ap); mfebc(pb3cr, cr);
+ mfebc(PB3AP, ap); mfebc(PB3CR, cr);
printf("3: AP=%08lx CP=%08lx\n", ap, cr);
- mfebc(pb4ap, ap); mfebc(pb4cr, cr);
+ mfebc(PB4AP, ap); mfebc(PB4CR, cr);
printf("4: AP=%08lx CP=%08lx\n", ap, cr);
printf("\n");
diff --git a/board/gdsys/compactcenter/compactcenter.c b/board/gdsys/compactcenter/compactcenter.c
index f448ef9..8a5ea30 100644
--- a/board/gdsys/compactcenter/compactcenter.c
+++ b/board/gdsys/compactcenter/compactcenter.c
@@ -215,7 +215,7 @@
EBC_BXCR_BS_128MB : EBC_BXCR_BS_64MB;
/* Remap the NOR FLASH to 0xcn00.0000 ... 0xcfff.ffff */
- mtebc(pb0cr, CONFIG_SYS_FLASH_BASE_PHYS_L
+ mtebc(PB0CR, CONFIG_SYS_FLASH_BASE_PHYS_L
| bxcr_bw
| EBC_BXCR_BU_RW
| EBC_BXCR_BW_16BIT);
diff --git a/board/gdsys/dlvision/dlvision.c b/board/gdsys/dlvision/dlvision.c
index 4ec1cdb..5246bc8 100644
--- a/board/gdsys/dlvision/dlvision.c
+++ b/board/gdsys/dlvision/dlvision.c
@@ -48,7 +48,7 @@
* EBC Configuration Register: set ready timeout to 512 ebc-clks
* -> ca. 15 us
*/
- mtebc(epcr, 0xa8400000); /* ebc always driven */
+ mtebc(EBC0_CFG, 0xa8400000); /* ebc always driven */
/*
* setup io-latches
diff --git a/board/gdsys/gdppc440etx/gdppc440etx.c b/board/gdsys/gdppc440etx/gdppc440etx.c
index a661057..27c159b 100644
--- a/board/gdsys/gdppc440etx/gdppc440etx.c
+++ b/board/gdsys/gdppc440etx/gdppc440etx.c
@@ -42,8 +42,8 @@
/*
* Setup the external bus controller/chip selects
*/
- mfebc(xbcfg, reg);
- mtebc(xbcfg, reg | 0x04000000); /* Set ATC */
+ mfebc(EBC0_CFG, reg);
+ mtebc(EBC0_CFG, reg | 0x04000000); /* Set ATC */
/*
* Setup the GPIO pins
@@ -102,10 +102,10 @@
/*
* Setup other serial configuration
*/
- mfsdr(sdr_pci0, reg);
- mtsdr(sdr_pci0, 0x80000000 | reg); /* PCI arbiter enabled */
- mtsdr(sdr_pfc0, 0x00003e00); /* Pin function */
- mtsdr(sdr_pfc1, 0x00048000); /* Pin function: UART0 has 4 pins */
+ mfsdr(SDR0_PCI0, reg);
+ mtsdr(SDR0_PCI0, 0x80000000 | reg); /* PCI arbiter enabled */
+ mtsdr(SDR0_PFC0, 0x00003e00); /* Pin function */
+ mtsdr(SDR0_PFC1, 0x00048000); /* Pin function: UART0 has 4 pins */
return 0;
}
@@ -117,7 +117,7 @@
uint sz;
/* Re-do sizing to get full correct info */
- mfebc(pb0cr, pbcr);
+ mfebc(PB0CR, pbcr);
if (gd->bd->bi_flashsize > 0x08000000)
panic("Max. flash banksize is 128 MB!\n");
@@ -127,7 +127,7 @@
sz <<= 1;
pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
- mtebc(pb0cr, pbcr);
+ mtebc(PB0CR, pbcr);
/* adjust flash start and offset */
gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
@@ -178,35 +178,35 @@
* Set priority for all PLB3 devices to 0.
* Set PLB3 arbiter to fair mode.
*/
- mfsdr(sdr_amp1, addr);
- mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(plb3_acr);
- mtdcr(plb3_acr, addr | 0x80000000);
+ mfsdr(SD0_AMP1, addr);
+ mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
+ addr = mfdcr(PLB3_ACR);
+ mtdcr(PLB3_ACR, addr | 0x80000000);
/*
* Set priority for all PLB4 devices to 0.
*/
- mfsdr(sdr_amp0, addr);
- mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(plb4_acr) | 0xa0000000; /* Was 0x8---- */
- mtdcr(plb4_acr, addr);
+ mfsdr(SD0_AMP0, addr);
+ mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
+ addr = mfdcr(PLB4_ACR) | 0xa0000000; /* Was 0x8---- */
+ mtdcr(PLB4_ACR, addr);
/*
* Set Nebula PLB4 arbiter to fair mode.
*/
/* Segment0 */
- addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair;
- addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled;
- addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep;
- addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep;
- mtdcr(plb0_acr, addr);
+ addr = (mfdcr(PLB0_ACR) & ~PLB0_ACR_PPM_MASK) | PLB0_ACR_PPM_FAIR;
+ addr = (addr & ~PLB0_ACR_HBU_MASK) | PLB0_ACR_HBU_ENABLED;
+ addr = (addr & ~PLB0_ACR_RDP_MASK) | PLB0_ACR_RDP_4DEEP;
+ addr = (addr & ~PLB0_ACR_WRP_MASK) | PLB0_ACR_WRP_2DEEP;
+ mtdcr(PLB0_ACR, addr);
/* Segment1 */
- addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair;
- addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled;
- addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep;
- addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep;
- mtdcr(plb1_acr, addr);
+ addr = (mfdcr(PLB1_ACR) & ~PLB1_ACR_PPM_MASK) | PLB1_ACR_PPM_FAIR;
+ addr = (addr & ~PLB1_ACR_HBU_MASK) | PLB1_ACR_HBU_ENABLED;
+ addr = (addr & ~PLB1_ACR_RDP_MASK) | PLB1_ACR_RDP_4DEEP;
+ addr = (addr & ~PLB1_ACR_WRP_MASK) | PLB1_ACR_WRP_2DEEP;
+ mtdcr(PLB1_ACR, addr);
/* enable 66 MHz ext. Clock */
out32(GPIO1_TCR, in32(GPIO1_TCR) | 0x00008000);
diff --git a/board/gdsys/neo/neo.c b/board/gdsys/neo/neo.c
index 817ce17..628ce3d 100644
--- a/board/gdsys/neo/neo.c
+++ b/board/gdsys/neo/neo.c
@@ -43,7 +43,7 @@
* EBC Configuration Register: set ready timeout to 512 ebc-clks
* -> ca. 15 us
*/
- mtebc(epcr, 0xa8400000); /* ebc always driven */
+ mtebc(EBC0_CFG, 0xa8400000); /* ebc always driven */
return 0;
}
diff --git a/board/jse/init.S b/board/jse/init.S
index 7b932b2..92f43f4 100644
--- a/board/jse/init.S
+++ b/board/jse/init.S
@@ -52,8 +52,6 @@
#include <asm/cache.h>
#include <asm/mmu.h>
-#define cpc0_cr0 0xB1
-
.globl ext_bus_cntlr_init
ext_bus_cntlr_init:
mflr r4 /* save link register */
@@ -84,16 +82,16 @@
/* Memory Bank 0 (Flash) initialization */
/*----------------------------------------------------------------- */
- addi r4,0,pb0ap
- mtdcr ebccfga,r4
+ addi r4,0,PB1AP
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,0x9B01
ori r4,r4,0x5480
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
- addi r4,0,pb0cr
- mtdcr ebccfga,r4
+ addi r4,0,PB0CR
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,0xFFF1 /* BAS=0xFFF,BS=0x0(1MB),BU=0x3(R/W), */
ori r4,r4,0x8000 /* BW=0x0( 8 bits) */
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
blr
diff --git a/board/jse/jse.c b/board/jse/jse.c
index 6a6b9dd..6dc9a01 100644
--- a/board/jse/jse.c
+++ b/board/jse/jse.c
@@ -62,12 +62,12 @@
/* EBC0_B1AP: BME=1, TWT=2, CSN=0, OEN=1,
WBN=0, WBF=1, TH=0, RE=0, SOR=0, BEM=0, PEN=0 */
- mtdcr (ebccfga, pb1ap);
- mtdcr (ebccfgd, 0x01011000);
+ mtdcr (EBC0_CFGADDR, PB1AP);
+ mtdcr (EBC0_CFGDATA, 0x01011000);
/* EBC0_B1CR: BAS=x, BS=0(1MB), BU=3(R/W), BW=0(8bits) */
- mtdcr (ebccfga, pb1cr);
- mtdcr (ebccfgd, CONFIG_SYS_SYSTEMACE_BASE | 0x00018000);
+ mtdcr (EBC0_CFGADDR, PB1CR);
+ mtdcr (EBC0_CFGDATA, CONFIG_SYS_SYSTEMACE_BASE | 0x00018000);
/* Enable the /PerWE output as /PerWE, instead of /PCIINT. */
/* CPC0_CR1 |= PCIPW */
diff --git a/board/jse/sdram.c b/board/jse/sdram.c
index a1f526d..bb6f85e 100644
--- a/board/jse/sdram.c
+++ b/board/jse/sdram.c
@@ -35,60 +35,60 @@
/* Configure the SDRAMS */
/* disable memory controller */
- mtdcr (memcfga, mem_mcopt1);
- mtdcr (memcfgd, 0x00000000);
+ mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
+ mtdcr (SDRAM0_CFGDATA, 0x00000000);
udelay (500);
/* Clear SDRAM0_BESR0 (Bus Error Syndrome Register) */
- mtdcr (memcfga, mem_besra);
- mtdcr (memcfgd, 0xffffffff);
+ mtdcr (SDRAM0_CFGADDR, mem_besra);
+ mtdcr (SDRAM0_CFGDATA, 0xffffffff);
/* Clear SDRAM0_BESR1 (Bus Error Syndrome Register) */
- mtdcr (memcfga, mem_besrb);
- mtdcr (memcfgd, 0xffffffff);
+ mtdcr (SDRAM0_CFGADDR, mem_besrb);
+ mtdcr (SDRAM0_CFGDATA, 0xffffffff);
/* Clear SDRAM0_ECCCFG (disable ECC) */
- mtdcr (memcfga, mem_ecccf);
- mtdcr (memcfgd, 0x00000000);
+ mtdcr (SDRAM0_CFGADDR, mem_ecccf);
+ mtdcr (SDRAM0_CFGDATA, 0x00000000);
/* Clear SDRAM0_ECCESR (ECC Error Syndrome Register) */
- mtdcr (memcfga, mem_eccerr);
- mtdcr (memcfgd, 0xffffffff);
+ mtdcr (SDRAM0_CFGADDR, mem_eccerr);
+ mtdcr (SDRAM0_CFGDATA, 0xffffffff);
/* Timing register: CASL=2, PTA=2, CTP=2, LDF=1, RFTA=5, RCD=2 */
- mtdcr (memcfga, mem_sdtr1);
- mtdcr (memcfgd, 0x010a4016);
+ mtdcr (SDRAM0_CFGADDR, mem_sdtr1);
+ mtdcr (SDRAM0_CFGDATA, 0x010a4016);
/* Memory Bank 0 Config == BA=0x00000000, SZ=64M, AM=3, BE=1 */
- mtdcr (memcfga, mem_mb0cf);
- mtdcr (memcfgd, 0x00084001);
+ mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
+ mtdcr (SDRAM0_CFGDATA, 0x00084001);
/* Memory Bank 1 Config == BA=0x04000000, SZ=64M, AM=3, BE=1 */
- mtdcr (memcfga, mem_mb1cf);
- mtdcr (memcfgd, 0x04084001);
+ mtdcr (SDRAM0_CFGADDR, mem_mb1cf);
+ mtdcr (SDRAM0_CFGDATA, 0x04084001);
/* Memory Bank 2 Config == BE=0 */
- mtdcr (memcfga, mem_mb2cf);
- mtdcr (memcfgd, 0x00000000);
+ mtdcr (SDRAM0_CFGADDR, mem_mb2cf);
+ mtdcr (SDRAM0_CFGDATA, 0x00000000);
/* Memory Bank 3 Config == BE=0 */
- mtdcr (memcfga, mem_mb3cf);
- mtdcr (memcfgd, 0x00000000);
+ mtdcr (SDRAM0_CFGADDR, mem_mb3cf);
+ mtdcr (SDRAM0_CFGDATA, 0x00000000);
/* refresh timer = 0x400 */
- mtdcr (memcfga, mem_rtr);
- mtdcr (memcfgd, 0x04000000);
+ mtdcr (SDRAM0_CFGADDR, mem_rtr);
+ mtdcr (SDRAM0_CFGDATA, 0x04000000);
/* Power management idle timer set to the default. */
- mtdcr (memcfga, mem_pmit);
- mtdcr (memcfgd, 0x07c00000);
+ mtdcr (SDRAM0_CFGADDR, mem_pmit);
+ mtdcr (SDRAM0_CFGDATA, 0x07c00000);
udelay (500);
/* Enable banks (DCE=1, BPRF=1, ECCDD=1, EMDUL=1) */
- mtdcr (memcfga, mem_mcopt1);
- mtdcr (memcfgd, 0x80e00000);
+ mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
+ mtdcr (SDRAM0_CFGDATA, 0x80e00000);
return SDRAM_LEN;
}
@@ -108,28 +108,28 @@
#ifdef DEBUG
printf ("SDRAM Controller Registers --\n");
- mtdcr (memcfga, mem_mcopt1);
- val = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
+ val = mfdcr (SDRAM0_CFGDATA);
printf (" SDRAM0_CFG : 0x%08x\n", val);
- mtdcr (memcfga, 0x24);
- val = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, 0x24);
+ val = mfdcr (SDRAM0_CFGDATA);
printf (" SDRAM0_STATUS: 0x%08x\n", val);
- mtdcr (memcfga, mem_mb0cf);
- val = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
+ val = mfdcr (SDRAM0_CFGDATA);
printf (" SDRAM0_B0CR : 0x%08x\n", val);
- mtdcr (memcfga, mem_mb1cf);
- val = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_mb1cf);
+ val = mfdcr (SDRAM0_CFGDATA);
printf (" SDRAM0_B1CR : 0x%08x\n", val);
- mtdcr (memcfga, mem_sdtr1);
- val = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_sdtr1);
+ val = mfdcr (SDRAM0_CFGDATA);
printf (" SDRAM0_TR : 0x%08x\n", val);
- mtdcr (memcfga, mem_rtr);
- val = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_rtr);
+ val = mfdcr (SDRAM0_CFGDATA);
printf (" SDRAM0_RTR : 0x%08x\n", val);
#endif
@@ -137,8 +137,8 @@
bit. Really, there should already have been plenty of time,
given it was started long ago. But, best to check. */
for (idx = 0; idx < 1000000; idx += 1) {
- mtdcr (memcfga, 0x24);
- val = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, 0x24);
+ val = mfdcr (SDRAM0_CFGDATA);
if (val & 0x80000000)
break;
}
diff --git a/board/korat/korat.c b/board/korat/korat.c
index 8328ba3..3d4d149 100644
--- a/board/korat/korat.c
+++ b/board/korat/korat.c
@@ -81,8 +81,8 @@
korat_buzzer(0);
#endif
- mtdcr(ebccfga, xbcfg);
- mtdcr(ebccfgd, 0xb8400000);
+ mtdcr(EBC0_CFGADDR, EBC0_CFG);
+ mtdcr(EBC0_CFGDATA, 0xb8400000);
/*
* Setup the interrupt controller polarities, triggers, etc.
@@ -157,8 +157,8 @@
mtsdr(SDR0_PFC1, sdr0_pfc1);
/* PCI arbiter enabled */
- mfsdr(sdr_pci0, reg);
- mtsdr(sdr_pci0, 0x80000000 | reg);
+ mfsdr(SDR0_PCI0, reg);
+ mtsdr(SDR0_PCI0, 0x80000000 | reg);
return 0;
}
@@ -359,12 +359,12 @@
gd->bd->bi_flashstart = CONFIG_SYS_FLASH1_TOP - flash1_size;
gd->bd->bi_flashoffset = 0;
- mtdcr(ebccfga, pb1cr);
- pbcr = mfdcr(ebccfgd);
+ mtdcr(EBC0_CFGADDR, PB1CR);
+ pbcr = mfdcr(EBC0_CFGDATA);
size_val = ffs(flash1_size) - 21;
pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
- mtdcr(ebccfga, pb1cr);
- mtdcr(ebccfgd, pbcr);
+ mtdcr(EBC0_CFGADDR, PB1CR);
+ mtdcr(EBC0_CFGDATA, pbcr);
/*
* Re-check to get correct base address
@@ -378,12 +378,12 @@
gd->bd->bi_flashoffset =
CONFIG_ENV_ADDR_REDUND + CONFIG_ENV_SECT_SIZE - CONFIG_SYS_FLASH1_ADDR;
- mtdcr(ebccfga, pb1cr);
- pbcr = mfdcr(ebccfgd);
+ mtdcr(EBC0_CFGADDR, PB1CR);
+ pbcr = mfdcr(EBC0_CFGDATA);
size_val = ffs(gd->bd->bi_flashsize - CONFIG_SYS_FLASH0_SIZE) - 21;
pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
- mtdcr(ebccfga, pb1cr);
- mtdcr(ebccfgd, pbcr);
+ mtdcr(EBC0_CFGADDR, PB1CR);
+ mtdcr(EBC0_CFGDATA, pbcr);
/* Monitor protection ON by default */
#if defined(CONFIG_KORAT_PERMANENT)
@@ -552,8 +552,8 @@
* This fix will make the MAL burst disabling patch for the Linux
* EMAC driver obsolete.
*/
- reg = mfdcr(plb4_acr) & ~PLB4_ACR_WRP;
- mtdcr(plb4_acr, reg);
+ reg = mfdcr(PLB4_ACR) & ~PLB4_ACR_WRP;
+ mtdcr(PLB4_ACR, reg);
set_serial_number();
set_mac_addresses();
@@ -620,35 +620,35 @@
* Set priority for all PLB3 devices to 0.
* Set PLB3 arbiter to fair mode.
*/
- mfsdr(sdr_amp1, addr);
- mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(plb3_acr);
- mtdcr(plb3_acr, addr | 0x80000000);
+ mfsdr(SD0_AMP1, addr);
+ mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
+ addr = mfdcr(PLB3_ACR);
+ mtdcr(PLB3_ACR, addr | 0x80000000);
/*
* Set priority for all PLB4 devices to 0.
*/
- mfsdr(sdr_amp0, addr);
- mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(plb4_acr) | 0xa0000000; /* Was 0x8---- */
- mtdcr(plb4_acr, addr);
+ mfsdr(SD0_AMP0, addr);
+ mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
+ addr = mfdcr(PLB4_ACR) | 0xa0000000; /* Was 0x8---- */
+ mtdcr(PLB4_ACR, addr);
/*
* Set Nebula PLB4 arbiter to fair mode.
*/
/* Segment0 */
- addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair;
- addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled;
- addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep;
- addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep;
- mtdcr(plb0_acr, addr);
+ addr = (mfdcr(PLB0_ACR) & ~PLB0_ACR_PPM_MASK) | PLB0_ACR_PPM_FAIR;
+ addr = (addr & ~PLB0_ACR_HBU_MASK) | PLB0_ACR_HBU_ENABLED;
+ addr = (addr & ~PLB0_ACR_RDP_MASK) | PLB0_ACR_RDP_4DEEP;
+ addr = (addr & ~PLB0_ACR_WRP_MASK) | PLB0_ACR_WRP_2DEEP;
+ mtdcr(PLB0_ACR, addr);
/* Segment1 */
- addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair;
- addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled;
- addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep;
- addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep;
- mtdcr(plb1_acr, addr);
+ addr = (mfdcr(PLB1_ACR) & ~PLB1_ACR_PPM_MASK) | PLB1_ACR_PPM_FAIR;
+ addr = (addr & ~PLB1_ACR_HBU_MASK) | PLB1_ACR_HBU_ENABLED;
+ addr = (addr & ~PLB1_ACR_RDP_MASK) | PLB1_ACR_RDP_4DEEP;
+ addr = (addr & ~PLB1_ACR_WRP_MASK) | PLB1_ACR_WRP_2DEEP;
+ mtdcr(PLB1_ACR, addr);
#if defined(CONFIG_PCI_PNP)
hose->fixup_irq = korat_pci_fixup_irq;
diff --git a/board/lwmon5/lwmon5.c b/board/lwmon5/lwmon5.c
index 9b76e76..a9c2a6f 100644
--- a/board/lwmon5/lwmon5.c
+++ b/board/lwmon5/lwmon5.c
@@ -38,8 +38,8 @@
u32 reg;
/* PLB Write pipelining disabled. Denali Core workaround */
- mtdcr(plb0_acr, 0xDE000000);
- mtdcr(plb1_acr, 0xDE000000);
+ mtdcr(PLB0_ACR, 0xDE000000);
+ mtdcr(PLB1_ACR, 0xDE000000);
/*--------------------------------------------------------------------
* Setup the interrupt controller polarities, triggers, etc.
@@ -90,9 +90,9 @@
/* PCI arbiter disabled */
/* PCI Host Configuration disbaled */
- mfsdr(sdr_pci0, reg);
+ mfsdr(SDR0_PCI0, reg);
reg = 0;
- mtsdr(sdr_pci0, 0x00000000 | reg);
+ mtsdr(SDR0_PCI0, 0x00000000 | reg);
gpio_write_bit(CONFIG_SYS_GPIO_FLASH_WP, 1);
@@ -157,7 +157,7 @@
gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
gd->bd->bi_flashoffset = 0;
- mfebc(pb0cr, pbcr);
+ mfebc(PB0CR, pbcr);
switch (gd->bd->bi_flashsize) {
case 1 << 20:
size_val = 0;
@@ -185,7 +185,7 @@
break;
}
pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
- mtebc(pb0cr, pbcr);
+ mtebc(PB0CR, pbcr);
/*
* Re-check to get correct base address
@@ -249,8 +249,8 @@
* This fix will make the MAL burst disabling patch for the Linux
* EMAC driver obsolete.
*/
- reg = mfdcr(plb4_acr) & ~PLB4_ACR_WRP;
- mtdcr(plb4_acr, reg);
+ reg = mfdcr(PLB4_ACR) & ~PLB4_ACR_WRP;
+ mtdcr(PLB4_ACR, reg);
/*
* Init matrix keyboard
@@ -296,35 +296,35 @@
| Set priority for all PLB3 devices to 0.
| Set PLB3 arbiter to fair mode.
+-------------------------------------------------------------------------*/
- mfsdr(sdr_amp1, addr);
- mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(plb3_acr);
- mtdcr(plb3_acr, addr | 0x80000000);
+ mfsdr(SD0_AMP1, addr);
+ mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
+ addr = mfdcr(PLB3_ACR);
+ mtdcr(PLB3_ACR, addr | 0x80000000);
/*-------------------------------------------------------------------------+
| Set priority for all PLB4 devices to 0.
+-------------------------------------------------------------------------*/
- mfsdr(sdr_amp0, addr);
- mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(plb4_acr) | 0xa0000000; /* Was 0x8---- */
- mtdcr(plb4_acr, addr);
+ mfsdr(SD0_AMP0, addr);
+ mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
+ addr = mfdcr(PLB4_ACR) | 0xa0000000; /* Was 0x8---- */
+ mtdcr(PLB4_ACR, addr);
/*-------------------------------------------------------------------------+
| Set Nebula PLB4 arbiter to fair mode.
+-------------------------------------------------------------------------*/
/* Segment0 */
- addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair;
- addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled;
- addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep;
- addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep;
- mtdcr(plb0_acr, addr);
+ addr = (mfdcr(PLB0_ACR) & ~PLB0_ACR_PPM_MASK) | PLB0_ACR_PPM_FAIR;
+ addr = (addr & ~PLB0_ACR_HBU_MASK) | PLB0_ACR_HBU_ENABLED;
+ addr = (addr & ~PLB0_ACR_RDP_MASK) | PLB0_ACR_RDP_4DEEP;
+ addr = (addr & ~PLB0_ACR_WRP_MASK) | PLB0_ACR_WRP_2DEEP;
+ mtdcr(PLB0_ACR, addr);
/* Segment1 */
- addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair;
- addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled;
- addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep;
- addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep;
- mtdcr(plb1_acr, addr);
+ addr = (mfdcr(PLB1_ACR) & ~PLB1_ACR_PPM_MASK) | PLB1_ACR_PPM_FAIR;
+ addr = (addr & ~PLB1_ACR_HBU_MASK) | PLB1_ACR_HBU_ENABLED;
+ addr = (addr & ~PLB1_ACR_RDP_MASK) | PLB1_ACR_RDP_4DEEP;
+ addr = (addr & ~PLB1_ACR_WRP_MASK) | PLB1_ACR_WRP_2DEEP;
+ mtdcr(PLB1_ACR, addr);
return 1;
}
diff --git a/board/mpl/common/flash.c b/board/mpl/common/flash.c
index 355608c..682f0e7 100644
--- a/board/mpl/common/flash.c
+++ b/board/mpl/common/flash.c
@@ -97,7 +97,7 @@
{
unsigned long pbcr;
int res = 0;
- pbcr = mfdcr (strap);
+ pbcr = mfdcr (CPC0_PSR);
if ((pbcr & PSR_ROM_WIDTH_MASK) == 0)
/* boot via MPS or MPS mapping */
res = BOOT_MPS;
@@ -123,29 +123,29 @@
/* first findout on which cs the flash is */
if(mode & BOOT_MPS) {
/* map flash high on CS1 and MPS on CS0 */
- mtdcr (ebccfga, pb0ap);
- mtdcr (ebccfgd, MPS_AP);
- mtdcr (ebccfga, pb0cr);
- mtdcr (ebccfgd, MPS_CR);
+ mtdcr (EBC0_CFGADDR, PB0AP);
+ mtdcr (EBC0_CFGDATA, MPS_AP);
+ mtdcr (EBC0_CFGADDR, PB0CR);
+ mtdcr (EBC0_CFGDATA, MPS_CR);
/* we use the default values (max values) for the flash
* because its real size is not yet known */
- mtdcr (ebccfga, pb1ap);
- mtdcr (ebccfgd, FLASH_AP);
- mtdcr (ebccfga, pb1cr);
- mtdcr (ebccfgd, FLASH_CR_B);
+ mtdcr (EBC0_CFGADDR, PB1AP);
+ mtdcr (EBC0_CFGDATA, FLASH_AP);
+ mtdcr (EBC0_CFGADDR, PB1CR);
+ mtdcr (EBC0_CFGDATA, FLASH_CR_B);
}
else {
/* map flash high on CS0 and MPS on CS1 */
- mtdcr (ebccfga, pb1ap);
- mtdcr (ebccfgd, MPS_AP);
- mtdcr (ebccfga, pb1cr);
- mtdcr (ebccfgd, MPS_CR);
+ mtdcr (EBC0_CFGADDR, PB1AP);
+ mtdcr (EBC0_CFGDATA, MPS_AP);
+ mtdcr (EBC0_CFGADDR, PB1CR);
+ mtdcr (EBC0_CFGDATA, MPS_CR);
/* we use the default values (max values) for the flash
* because its real size is not yet known */
- mtdcr (ebccfga, pb0ap);
- mtdcr (ebccfgd, FLASH_AP);
- mtdcr (ebccfga, pb0cr);
- mtdcr (ebccfgd, FLASH_CR_B);
+ mtdcr (EBC0_CFGADDR, PB0AP);
+ mtdcr (EBC0_CFGDATA, FLASH_AP);
+ mtdcr (EBC0_CFGADDR, PB0CR);
+ mtdcr (EBC0_CFGDATA, FLASH_CR_B);
}
}
@@ -217,34 +217,34 @@
}
if(mode & BOOT_MPS) {
/* flash is on CS1 */
- mtdcr(ebccfga, pb1cr);
- flashcr = mfdcr (ebccfgd);
+ mtdcr(EBC0_CFGADDR, PB1CR);
+ flashcr = mfdcr (EBC0_CFGDATA);
/* we map the flash high in every case */
flashcr&=0x0001FFFF; /* mask out address bits */
flashcr|= ((0-flash_info[0].size) & 0xFFF00000); /* start addr */
flashcr|= (i << 17); /* size addr */
- mtdcr(ebccfga, pb1cr);
- mtdcr(ebccfgd, flashcr);
+ mtdcr(EBC0_CFGADDR, PB1CR);
+ mtdcr(EBC0_CFGDATA, flashcr);
}
else {
/* flash is on CS0 */
- mtdcr(ebccfga, pb0cr);
- flashcr = mfdcr (ebccfgd);
+ mtdcr(EBC0_CFGADDR, PB0CR);
+ flashcr = mfdcr (EBC0_CFGDATA);
/* we map the flash high in every case */
flashcr&=0x0001FFFF; /* mask out address bits */
flashcr|= ((0-flash_info[0].size) & 0xFFF00000); /* start addr */
flashcr|= (i << 17); /* size addr */
- mtdcr(ebccfga, pb0cr);
- mtdcr(ebccfgd, flashcr);
+ mtdcr(EBC0_CFGADDR, PB0CR);
+ mtdcr(EBC0_CFGDATA, flashcr);
}
#if 0
/* enable this (PIP405/MIP405 only) if you want to test if
the relocation has be done ok.
This will disable both Chipselects */
- mtdcr (ebccfga, pb0cr);
- mtdcr (ebccfgd, 0L);
- mtdcr (ebccfga, pb1cr);
- mtdcr (ebccfgd, 0L);
+ mtdcr (EBC0_CFGADDR, PB0CR);
+ mtdcr (EBC0_CFGDATA, 0L);
+ mtdcr (EBC0_CFGADDR, PB1CR);
+ mtdcr (EBC0_CFGDATA, 0L);
printf("CS0 & CS1 switched off for test\n");
#endif
/* patch version_string */
diff --git a/board/mpl/mip405/init.S b/board/mpl/mip405/init.S
index 19d9220..f3d94c3 100644
--- a/board/mpl/mip405/init.S
+++ b/board/mpl/mip405/init.S
@@ -55,7 +55,7 @@
.globl ext_bus_cntlr_init
ext_bus_cntlr_init:
mflr r4 /* save link register */
- mfdcr r3,strap /* get strapping reg */
+ mfdcr r3,CPC0_PSR /* get strapping reg */
andi. r0, r3, PSR_ROM_LOC /* mask out irrelevant bits */
bnelr /* jump back if PCI boot */
@@ -84,9 +84,9 @@
/*-----------------------------------------------------------------------
* decide boot up mode
*----------------------------------------------------------------------- */
- addi r4,0,pb0cr
- mtdcr ebccfga,r4
- mfdcr r4,ebccfgd
+ addi r4,0,PB0CR
+ mtdcr EBC0_CFGADDR,r4
+ mfdcr r4,EBC0_CFGDATA
andi. r0, r4, 0x2000 /* mask out irrelevant bits */
beq 0f /* jump if 8 bit bus width */
@@ -96,18 +96,18 @@
* Memory Bank 0 (16 Bit Flash) initialization
*---------------------------------------------------------------------- */
- addi r4,0,pb0ap
- mtdcr ebccfga,r4
+ addi r4,0,PB1AP
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,(FLASH_AP_B)@h
ori r4,r4,(FLASH_AP_B)@l
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
- addi r4,0,pb0cr
- mtdcr ebccfga,r4
+ addi r4,0,PB0CR
+ mtdcr EBC0_CFGADDR,r4
/* BS=0x010(4MB),BU=0x3(R/W), */
addis r4,0,(FLASH_CR_B)@h
ori r4,r4,(FLASH_CR_B)@l
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
b 1f
0:
@@ -117,66 +117,66 @@
* Memory Bank 0 Multi Purpose Socket initialization
*----------------------------------------------------------------------- */
/* 0x7F8FFE80 slowest boot */
- addi r4,0,pb0ap
- mtdcr ebccfga,r4
+ addi r4,0,PB1AP
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,(MPS_AP_B)@h
ori r4,r4,(MPS_AP_B)@l
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
- addi r4,0,pb0cr
- mtdcr ebccfga,r4
+ addi r4,0,PB0CR
+ mtdcr EBC0_CFGADDR,r4
/* BS=0x010(4MB),BU=0x3(R/W), */
addis r4,0,(MPS_CR_B)@h
ori r4,r4,(MPS_CR_B)@l
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
1:
/*-----------------------------------------------------------------------
* Memory Bank 2-3-4-5-6 (not used) initialization
*-----------------------------------------------------------------------*/
- addi r4,0,pb1cr
- mtdcr ebccfga,r4
+ addi r4,0,PB1CR
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,0x0000
ori r4,r4,0x0000
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
- addi r4,0,pb2cr
- mtdcr ebccfga,r4
+ addi r4,0,PB2CR
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,0x0000
ori r4,r4,0x0000
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
- addi r4,0,pb3cr
- mtdcr ebccfga,r4
+ addi r4,0,PB3CR
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,0x0000
ori r4,r4,0x0000
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
- addi r4,0,pb4cr
- mtdcr ebccfga,r4
+ addi r4,0,PB4CR
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,0x0000
ori r4,r4,0x0000
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
- addi r4,0,pb5cr
- mtdcr ebccfga,r4
+ addi r4,0,PB5CR
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,0x0000
ori r4,r4,0x0000
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
- addi r4,0,pb6cr
- mtdcr ebccfga,r4
+ addi r4,0,PB6CR
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,0x0000
ori r4,r4,0x0000
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
- addi r4,0,pb7cr
- mtdcr ebccfga,r4
+ addi r4,0,PB7CR
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,0x0000
ori r4,r4,0x0000
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
nop /* pass2 DCR errata #8 */
blr
diff --git a/board/mpl/mip405/mip405.c b/board/mpl/mip405/mip405.c
index 1738f54..d8279e8 100644
--- a/board/mpl/mip405/mip405.c
+++ b/board/mpl/mip405/mip405.c
@@ -256,16 +256,16 @@
gd->baudrate = 9600;
serial_init ();
/* set up the pld */
- mtdcr (ebccfga, pb7ap);
- mtdcr (ebccfgd, PLD_AP);
- mtdcr (ebccfga, pb7cr);
- mtdcr (ebccfgd, PLD_CR);
+ mtdcr (EBC0_CFGADDR, PB7AP);
+ mtdcr (EBC0_CFGDATA, PLD_AP);
+ mtdcr (EBC0_CFGADDR, PB7CR);
+ mtdcr (EBC0_CFGDATA, PLD_CR);
/* THIS IS OBSOLETE */
/* set up the board rev reg*/
- mtdcr (ebccfga, pb5ap);
- mtdcr (ebccfgd, BOARD_AP);
- mtdcr (ebccfga, pb5cr);
- mtdcr (ebccfgd, BOARD_CR);
+ mtdcr (EBC0_CFGADDR, PB5AP);
+ mtdcr (EBC0_CFGDATA, BOARD_AP);
+ mtdcr (EBC0_CFGADDR, PB5CR);
+ mtdcr (EBC0_CFGDATA, BOARD_CR);
#ifdef SDRAM_DEBUG
/* get all informations from PLD */
serial_puts ("\nPLD Part 0x");
@@ -289,30 +289,30 @@
SDRAM_err ("U-Boot configured for a MIP405 not for a MIP405T!!!\n");
#endif
/* set-up the chipselect machine */
- mtdcr (ebccfga, pb0cr); /* get cs0 config reg */
- tmp = mfdcr (ebccfgd);
+ mtdcr (EBC0_CFGADDR, PB0CR); /* get cs0 config reg */
+ tmp = mfdcr (EBC0_CFGDATA);
if ((tmp & 0x00002000) == 0) {
/* MPS Boot, set up the flash */
- mtdcr (ebccfga, pb1ap);
- mtdcr (ebccfgd, FLASH_AP);
- mtdcr (ebccfga, pb1cr);
- mtdcr (ebccfgd, FLASH_CR);
+ mtdcr (EBC0_CFGADDR, PB1AP);
+ mtdcr (EBC0_CFGDATA, FLASH_AP);
+ mtdcr (EBC0_CFGADDR, PB1CR);
+ mtdcr (EBC0_CFGDATA, FLASH_CR);
} else {
/* Flash boot, set up the MPS */
- mtdcr (ebccfga, pb1ap);
- mtdcr (ebccfgd, MPS_AP);
- mtdcr (ebccfga, pb1cr);
- mtdcr (ebccfgd, MPS_CR);
+ mtdcr (EBC0_CFGADDR, PB1AP);
+ mtdcr (EBC0_CFGDATA, MPS_AP);
+ mtdcr (EBC0_CFGADDR, PB1CR);
+ mtdcr (EBC0_CFGDATA, MPS_CR);
}
/* set up UART0 (CS2) and UART1 (CS3) */
- mtdcr (ebccfga, pb2ap);
- mtdcr (ebccfgd, UART0_AP);
- mtdcr (ebccfga, pb2cr);
- mtdcr (ebccfgd, UART0_CR);
- mtdcr (ebccfga, pb3ap);
- mtdcr (ebccfgd, UART1_AP);
- mtdcr (ebccfga, pb3cr);
- mtdcr (ebccfgd, UART1_CR);
+ mtdcr (EBC0_CFGADDR, PB2AP);
+ mtdcr (EBC0_CFGDATA, UART0_AP);
+ mtdcr (EBC0_CFGADDR, PB2CR);
+ mtdcr (EBC0_CFGDATA, UART0_CR);
+ mtdcr (EBC0_CFGADDR, PB3AP);
+ mtdcr (EBC0_CFGDATA, UART1_AP);
+ mtdcr (EBC0_CFGADDR, PB3CR);
+ mtdcr (EBC0_CFGDATA, UART1_CR);
bc = in8 (PLD_BOARD_CFG_REG);
#ifdef SDRAM_DEBUG
serial_puts ("\nstart SDRAM Setup\n");
@@ -348,8 +348,8 @@
/* trc_clocks is sum of trp_clocks + tras_clocks */
trc_clocks = trp_clocks + tras_clocks;
/* get SDRAM timing register */
- mtdcr (memcfga, mem_sdtr1);
- sdram_tim = mfdcr (memcfgd) & ~0x018FC01F;
+ mtdcr (SDRAM0_CFGADDR, mem_sdtr1);
+ sdram_tim = mfdcr (SDRAM0_CFGDATA) & ~0x018FC01F;
/* insert CASL value */
sdram_tim |= ((unsigned long) (cal_val)) << 23;
/* insert PTA value */
@@ -369,8 +369,8 @@
/* insert SZ value; */
tmp |= ((unsigned long) sdram_table[i].sz << 17);
/* get SDRAM bank 0 register */
- mtdcr (memcfga, mem_mb0cf);
- sdram_bank = mfdcr (memcfgd) & ~0xFFCEE001;
+ mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
+ sdram_bank = mfdcr (SDRAM0_CFGDATA) & ~0xFFCEE001;
sdram_bank |= (baseaddr | tmp | 0x01);
#ifdef SDRAM_DEBUG
@@ -380,8 +380,8 @@
#endif
/* write SDRAM timing register */
- mtdcr (memcfga, mem_sdtr1);
- mtdcr (memcfgd, sdram_tim);
+ mtdcr (SDRAM0_CFGADDR, mem_sdtr1);
+ mtdcr (SDRAM0_CFGDATA, sdram_tim);
#ifdef SDRAM_DEBUG
serial_puts ("mb0cf: ");
@@ -390,23 +390,23 @@
#endif
/* write SDRAM bank 0 register */
- mtdcr (memcfga, mem_mb0cf);
- mtdcr (memcfgd, sdram_bank);
+ mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
+ mtdcr (SDRAM0_CFGDATA, sdram_bank);
if (get_bus_freq (tmp) > 110000000) { /* > 110MHz */
/* get SDRAM refresh interval register */
- mtdcr (memcfga, mem_rtr);
- tmp = mfdcr (memcfgd) & ~0x3FF80000;
+ mtdcr (SDRAM0_CFGADDR, mem_rtr);
+ tmp = mfdcr (SDRAM0_CFGDATA) & ~0x3FF80000;
tmp |= 0x07F00000;
} else {
/* get SDRAM refresh interval register */
- mtdcr (memcfga, mem_rtr);
- tmp = mfdcr (memcfgd) & ~0x3FF80000;
+ mtdcr (SDRAM0_CFGADDR, mem_rtr);
+ tmp = mfdcr (SDRAM0_CFGDATA) & ~0x3FF80000;
tmp |= 0x05F00000;
}
/* write SDRAM refresh interval register */
- mtdcr (memcfga, mem_rtr);
- mtdcr (memcfgd, tmp);
+ mtdcr (SDRAM0_CFGADDR, mem_rtr);
+ mtdcr (SDRAM0_CFGDATA, tmp);
/* enable ECC if used */
#if defined(ENABLE_ECC) && !defined(CONFIG_BOOT_PCI)
if (sdram_table[i].ecc) {
@@ -415,19 +415,19 @@
#ifdef SDRAM_DEBUG
serial_puts ("disable ECC.. ");
#endif
- mtdcr (memcfga, mem_ecccf);
- tmp = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_ecccf);
+ tmp = mfdcr (SDRAM0_CFGDATA);
tmp &= 0xff0fffff; /* disable all banks */
- mtdcr (memcfga, mem_ecccf);
+ mtdcr (SDRAM0_CFGADDR, mem_ecccf);
/* set up SDRAM Controller with ECC enabled */
#ifdef SDRAM_DEBUG
serial_puts ("setup SDRAM Controller.. ");
#endif
- mtdcr (memcfgd, tmp);
- mtdcr (memcfga, mem_mcopt1);
- tmp = (mfdcr (memcfgd) & ~0xFFE00000) | 0x90800000;
- mtdcr (memcfga, mem_mcopt1);
- mtdcr (memcfgd, tmp);
+ mtdcr (SDRAM0_CFGDATA, tmp);
+ mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
+ tmp = (mfdcr (SDRAM0_CFGDATA) & ~0xFFE00000) | 0x90800000;
+ mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
+ mtdcr (SDRAM0_CFGDATA, tmp);
udelay (600);
#ifdef SDRAM_DEBUG
serial_puts ("fill the memory..\n");
@@ -447,19 +447,19 @@
serial_puts ("enable ECC\n");
#endif
udelay (400);
- mtdcr (memcfga, mem_ecccf);
- tmp = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_ecccf);
+ tmp = mfdcr (SDRAM0_CFGDATA);
tmp |= 0x00800000; /* enable bank 0 */
- mtdcr (memcfgd, tmp);
+ mtdcr (SDRAM0_CFGDATA, tmp);
udelay (400);
} else
#endif
{
/* enable SDRAM controller with no ECC, 32-bit SDRAM width, 16 byte burst */
- mtdcr (memcfga, mem_mcopt1);
- tmp = (mfdcr (memcfgd) & ~0xFFE00000) | 0x80C00000;
- mtdcr (memcfga, mem_mcopt1);
- mtdcr (memcfgd, tmp);
+ mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
+ tmp = (mfdcr (SDRAM0_CFGDATA) & ~0xFFE00000) | 0x80C00000;
+ mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
+ mtdcr (SDRAM0_CFGDATA, tmp);
udelay (400);
}
serial_puts ("\n");
@@ -631,14 +631,14 @@
ds = 0;
/* since the DRAM controller is allready set up, calculate the size with the
bank registers */
- mtdcr (memcfga, mem_mb0cf);
- bank_reg[0] = mfdcr (memcfgd);
- mtdcr (memcfga, mem_mb1cf);
- bank_reg[1] = mfdcr (memcfgd);
- mtdcr (memcfga, mem_mb2cf);
- bank_reg[2] = mfdcr (memcfgd);
- mtdcr (memcfga, mem_mb3cf);
- bank_reg[3] = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
+ bank_reg[0] = mfdcr (SDRAM0_CFGDATA);
+ mtdcr (SDRAM0_CFGADDR, mem_mb1cf);
+ bank_reg[1] = mfdcr (SDRAM0_CFGDATA);
+ mtdcr (SDRAM0_CFGADDR, mem_mb2cf);
+ bank_reg[2] = mfdcr (SDRAM0_CFGDATA);
+ mtdcr (SDRAM0_CFGADDR, mem_mb3cf);
+ bank_reg[3] = mfdcr (SDRAM0_CFGDATA);
TotalSize = 0;
for (i = 0; i < 4; i++) {
if ((bank_reg[i] & 0x1) == 0x1) {
@@ -648,8 +648,8 @@
} else
ds = 1;
}
- mtdcr (memcfga, mem_ecccf);
- tmp = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_ecccf);
+ tmp = mfdcr (SDRAM0_CFGDATA);
if (!tmp)
printf ("No ");
@@ -687,7 +687,7 @@
rtc_get (&tm);
start=get_timer(0);
/* if MIP405 has booted from PCI, reset CCR0[24] as described in errata PCI_18 */
- if (mfdcr(strap) & PSR_ROM_LOC)
+ if (mfdcr(CPC0_PSR) & PSR_ROM_LOC)
mtspr(SPRN_CCR0, (mfspr(SPRN_CCR0) & ~0x80));
return (0);
diff --git a/board/mpl/pip405/init.S b/board/mpl/pip405/init.S
index 61f37d7..18e8b09 100644
--- a/board/mpl/pip405/init.S
+++ b/board/mpl/pip405/init.S
@@ -54,7 +54,7 @@
.globl ext_bus_cntlr_init
ext_bus_cntlr_init:
mflr r4 /* save link register */
- mfdcr r3,strap /* get strapping reg */
+ mfdcr r3,CPC0_PSR /* get strapping reg */
andi. r0, r3, PSR_ROM_LOC /* mask out irrelevant bits */
bnelr /* jump back if PCI boot */
@@ -83,9 +83,9 @@
/*-----------------------------------------------------------------------
* decide boot up mode
*----------------------------------------------------------------------- */
- addi r4,0,pb0cr
- mtdcr ebccfga,r4
- mfdcr r4,ebccfgd
+ addi r4,0,PB0CR
+ mtdcr EBC0_CFGADDR,r4
+ mfdcr r4,EBC0_CFGDATA
andi. r0, r4, 0x2000 /* mask out irrelevant bits */
beq 0f /* jump if 8 bit bus width */
@@ -95,18 +95,18 @@
* Memory Bank 0 (16 Bit Flash) initialization
*---------------------------------------------------------------------- */
- addi r4,0,pb0ap
- mtdcr ebccfga,r4
+ addi r4,0,PB1AP
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,(FLASH_AP_B)@h
ori r4,r4,(FLASH_AP_B)@l
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
- addi r4,0,pb0cr
- mtdcr ebccfga,r4
+ addi r4,0,PB0CR
+ mtdcr EBC0_CFGADDR,r4
/* BS=0x010(4MB),BU=0x3(R/W), */
addis r4,0,(FLASH_CR_B)@h
ori r4,r4,(FLASH_CR_B)@l
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
b 1f
0:
@@ -115,65 +115,65 @@
* Memory Bank 0 Multi Purpose Socket initialization
*----------------------------------------------------------------------- */
/* 0x7F8FFE80 slowest boot */
- addi r4,0,pb0ap
- mtdcr ebccfga,r4
+ addi r4,0,PB1AP
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,(MPS_AP_B)@h
ori r4,r4,(MPS_AP_B)@l
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
- addi r4,0,pb0cr
- mtdcr ebccfga,r4
+ addi r4,0,PB0CR
+ mtdcr EBC0_CFGADDR,r4
/* BS=0x010(4MB),BU=0x3(R/W), */
addis r4,0,(MPS_CR_B)@h
ori r4,r4,(MPS_CR_B)@l
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
1:
/*-----------------------------------------------------------------------
* Memory Bank 2-3-4-5-6 (not used) initialization
*-----------------------------------------------------------------------*/
- addi r4,0,pb1cr
- mtdcr ebccfga,r4
+ addi r4,0,PB1CR
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,0x0000
ori r4,r4,0x0000
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
- addi r4,0,pb2cr
- mtdcr ebccfga,r4
+ addi r4,0,PB2CR
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,0x0000
ori r4,r4,0x0000
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
- addi r4,0,pb3cr
- mtdcr ebccfga,r4
+ addi r4,0,PB3CR
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,0x0000
ori r4,r4,0x0000
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
- addi r4,0,pb4cr
- mtdcr ebccfga,r4
+ addi r4,0,PB4CR
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,0x0000
ori r4,r4,0x0000
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
- addi r4,0,pb5cr
- mtdcr ebccfga,r4
+ addi r4,0,PB5CR
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,0x0000
ori r4,r4,0x0000
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
- addi r4,0,pb6cr
- mtdcr ebccfga,r4
+ addi r4,0,PB6CR
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,0x0000
ori r4,r4,0x0000
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
- addi r4,0,pb7cr
- mtdcr ebccfga,r4
+ addi r4,0,PB7CR
+ mtdcr EBC0_CFGADDR,r4
addis r4,0,0x0000
ori r4,r4,0x0000
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
nop /* pass2 DCR errata #8 */
blr
diff --git a/board/mpl/pip405/pip405.c b/board/mpl/pip405/pip405.c
index 677437d..e00d1d0 100644
--- a/board/mpl/pip405/pip405.c
+++ b/board/mpl/pip405/pip405.c
@@ -193,10 +193,10 @@
unsigned char cal_index, cal_val, spd_version, spd_chksum;
unsigned char buf[8];
/* set up the config port */
- mtdcr (ebccfga, pb7ap);
- mtdcr (ebccfgd, CONFIG_PORT_AP);
- mtdcr (ebccfga, pb7cr);
- mtdcr (ebccfgd, CONFIG_PORT_CR);
+ mtdcr (EBC0_CFGADDR, PB7AP);
+ mtdcr (EBC0_CFGDATA, CONFIG_PORT_AP);
+ mtdcr (EBC0_CFGADDR, PB7CR);
+ mtdcr (EBC0_CFGDATA, CONFIG_PORT_CR);
memclk = get_bus_freq (tmemclk);
tmemclk = 1000000000 / (memclk / 100); /* in 10 ps units */
@@ -361,8 +361,8 @@
SDRAM_err ("unsupported SDRAM");
/* get SDRAM timing register */
- mtdcr (memcfga, mem_sdtr1);
- tmp = mfdcr (memcfgd) & ~0x018FC01F;
+ mtdcr (SDRAM0_CFGADDR, mem_sdtr1);
+ tmp = mfdcr (SDRAM0_CFGDATA) & ~0x018FC01F;
/* insert CASL value */
/* tmp |= ((unsigned long)cal_val) << 23; */
tmp |= ((unsigned long) cal_val) << 23;
@@ -385,8 +385,8 @@
#endif
/* write SDRAM timing register */
- mtdcr (memcfga, mem_sdtr1);
- mtdcr (memcfgd, tmp);
+ mtdcr (SDRAM0_CFGADDR, mem_sdtr1);
+ mtdcr (SDRAM0_CFGDATA, tmp);
baseaddr = CONFIG_SYS_SDRAM_BASE;
bank_size = (((unsigned long) density) << 22) / 2;
/* insert AM value */
@@ -418,8 +418,8 @@
SDRAM_err ("unsupported SDRAM");
} /* endswitch */
/* get SDRAM bank 0 register */
- mtdcr (memcfga, mem_mb0cf);
- bank = mfdcr (memcfgd) & ~0xFFCEE001;
+ mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
+ bank = mfdcr (SDRAM0_CFGDATA) & ~0xFFCEE001;
bank |= (baseaddr | tmp | 0x01);
#ifdef SDRAM_DEBUG
serial_puts ("bank0: baseaddr: ");
@@ -434,12 +434,12 @@
sdram_size += bank_size;
/* write SDRAM bank 0 register */
- mtdcr (memcfga, mem_mb0cf);
- mtdcr (memcfgd, bank);
+ mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
+ mtdcr (SDRAM0_CFGDATA, bank);
/* get SDRAM bank 1 register */
- mtdcr (memcfga, mem_mb1cf);
- bank = mfdcr (memcfgd) & ~0xFFCEE001;
+ mtdcr (SDRAM0_CFGADDR, mem_mb1cf);
+ bank = mfdcr (SDRAM0_CFGDATA) & ~0xFFCEE001;
sdram_size = 0;
#ifdef SDRAM_DEBUG
@@ -459,12 +459,12 @@
serial_puts ("\n");
#endif
/* write SDRAM bank 1 register */
- mtdcr (memcfga, mem_mb1cf);
- mtdcr (memcfgd, bank);
+ mtdcr (SDRAM0_CFGADDR, mem_mb1cf);
+ mtdcr (SDRAM0_CFGDATA, bank);
/* get SDRAM bank 2 register */
- mtdcr (memcfga, mem_mb2cf);
- bank = mfdcr (memcfgd) & ~0xFFCEE001;
+ mtdcr (SDRAM0_CFGADDR, mem_mb2cf);
+ bank = mfdcr (SDRAM0_CFGDATA) & ~0xFFCEE001;
bank |= (baseaddr | tmp | 0x01);
@@ -482,12 +482,12 @@
sdram_size += bank_size;
/* write SDRAM bank 2 register */
- mtdcr (memcfga, mem_mb2cf);
- mtdcr (memcfgd, bank);
+ mtdcr (SDRAM0_CFGADDR, mem_mb2cf);
+ mtdcr (SDRAM0_CFGDATA, bank);
/* get SDRAM bank 3 register */
- mtdcr (memcfga, mem_mb3cf);
- bank = mfdcr (memcfgd) & ~0xFFCEE001;
+ mtdcr (SDRAM0_CFGADDR, mem_mb3cf);
+ bank = mfdcr (SDRAM0_CFGDATA) & ~0xFFCEE001;
#ifdef SDRAM_DEBUG
serial_puts ("bank3: baseaddr: ");
@@ -509,13 +509,13 @@
#endif
/* write SDRAM bank 3 register */
- mtdcr (memcfga, mem_mb3cf);
- mtdcr (memcfgd, bank);
+ mtdcr (SDRAM0_CFGADDR, mem_mb3cf);
+ mtdcr (SDRAM0_CFGDATA, bank);
/* get SDRAM refresh interval register */
- mtdcr (memcfga, mem_rtr);
- tmp = mfdcr (memcfgd) & ~0x3FF80000;
+ mtdcr (SDRAM0_CFGADDR, mem_rtr);
+ tmp = mfdcr (SDRAM0_CFGDATA) & ~0x3FF80000;
if (tmemclk < NSto10PS (16))
tmp |= 0x05F00000;
@@ -523,14 +523,14 @@
tmp |= 0x03F80000;
/* write SDRAM refresh interval register */
- mtdcr (memcfga, mem_rtr);
- mtdcr (memcfgd, tmp);
+ mtdcr (SDRAM0_CFGADDR, mem_rtr);
+ mtdcr (SDRAM0_CFGDATA, tmp);
/* enable SDRAM controller with no ECC, 32-bit SDRAM width, 16 byte burst */
- mtdcr (memcfga, mem_mcopt1);
- tmp = (mfdcr (memcfgd) & ~0xFFE00000) | 0x80E00000;
- mtdcr (memcfga, mem_mcopt1);
- mtdcr (memcfgd, tmp);
+ mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
+ tmp = (mfdcr (SDRAM0_CFGDATA) & ~0xFFE00000) | 0x80E00000;
+ mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
+ mtdcr (SDRAM0_CFGDATA, tmp);
/*-------------------------------------------------------------------------+
@@ -619,14 +619,14 @@
/* since the DRAM controller is allready set up,
* calculate the size with the bank registers
*/
- mtdcr (memcfga, mem_mb0cf);
- bank_reg[0] = mfdcr (memcfgd);
- mtdcr (memcfga, mem_mb1cf);
- bank_reg[1] = mfdcr (memcfgd);
- mtdcr (memcfga, mem_mb2cf);
- bank_reg[2] = mfdcr (memcfgd);
- mtdcr (memcfga, mem_mb3cf);
- bank_reg[3] = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
+ bank_reg[0] = mfdcr (SDRAM0_CFGDATA);
+ mtdcr (SDRAM0_CFGADDR, mem_mb1cf);
+ bank_reg[1] = mfdcr (SDRAM0_CFGDATA);
+ mtdcr (SDRAM0_CFGADDR, mem_mb2cf);
+ bank_reg[2] = mfdcr (SDRAM0_CFGDATA);
+ mtdcr (SDRAM0_CFGADDR, mem_mb3cf);
+ bank_reg[3] = mfdcr (SDRAM0_CFGDATA);
TotalSize = 0;
for (i = 0; i < 4; i++) {
if ((bank_reg[i] & 0x1) == 0x1) {
@@ -668,7 +668,7 @@
gd->bd->bi_flashoffset=0;
/* if PIP405 has booted from PCI, reset CCR0[24] as described in errata PCI_18 */
- if (mfdcr(strap) & PSR_ROM_LOC)
+ if (mfdcr(CPC0_PSR) & PSR_ROM_LOC)
mtspr(SPRN_CCR0, (mfspr(SPRN_CCR0) & ~0x80));
return (0);
diff --git a/board/netstal/hcu4/hcu4.c b/board/netstal/hcu4/hcu4.c
index aa8a097..40bec8e 100644
--- a/board/netstal/hcu4/hcu4.c
+++ b/board/netstal/hcu4/hcu4.c
@@ -92,7 +92,7 @@
u16 index = boardVersReg & 0x0f;
/* Cannot be done in board_early_init */
- mtdcr(cntrl0, CPC0_CR0_VALUE);
+ mtdcr(CPC0_CR0, CPC0_CR0_VALUE);
/* Force /RTS to active. The board it not wired quite
* correctly to use cts/rtc flow control, so just force the
diff --git a/board/netstal/hcu5/hcu5.c b/board/netstal/hcu5/hcu5.c
index 5eb33d3..836c034 100644
--- a/board/netstal/hcu5/hcu5.c
+++ b/board/netstal/hcu5/hcu5.c
@@ -94,8 +94,8 @@
}
mtsdr(SDR0_CP440, 0x0EAAEA02); /* [Nto1] = 1*/
#endif
- mtdcr(ebccfga, xbcfg);
- mtdcr(ebccfgd, 0xb8400000);
+ mtdcr(EBC0_CFGADDR, EBC0_CFG);
+ mtdcr(EBC0_CFGDATA, 0xb8400000);
/*
* Setup the GPIO pins
@@ -152,8 +152,8 @@
mtdcr(uic2tr, 0x00000000); /* per ref-board manual */
mtdcr(uic2vr, 0x00000000); /* int31 highest, base=0x000 */
mtdcr(uic2sr, 0xffffffff); /* clear all */
- mtsdr(sdr_pfc0, 0x00003E00); /* Pin function: */
- mtsdr(sdr_pfc1, 0x00848000); /* Pin function: UART0 has 4 pins */
+ mtsdr(SDR0_PFC0, 0x00003E00); /* Pin function: */
+ mtsdr(SDR0_PFC1, 0x00848000); /* Pin function: UART0 has 4 pins */
/* setup BOOT FLASH */
mtsdr(SDR0_CUST0, 0xC0082350);
@@ -324,7 +324,7 @@
{
u32 reg;
- mfsdr(sdr_pci0, reg);
+ mfsdr(SDR0_PCI0, reg);
return (reg & SDR0_XCR_PAE_MASK);
}
@@ -350,28 +350,28 @@
* Set priority for all PLB3 devices to 0.
* Set PLB3 arbiter to fair mode.
*/
- mfsdr(sdr_amp1, addr);
- mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(plb3_acr);
- mtdcr(plb3_acr, addr | 0x80000000); /* Sequoia */
+ mfsdr(SD0_AMP1, addr);
+ mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
+ addr = mfdcr(PLB3_ACR);
+ mtdcr(PLB3_ACR, addr | 0x80000000); /* Sequoia */
/*
* Set priority for all PLB4 devices to 0.
*/
- mfsdr(sdr_amp0, addr);
- mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(plb4_acr) | 0xa0000000; /* Was 0x8---- */
- mtdcr(plb4_acr, addr); /* Sequoia */
+ mfsdr(SD0_AMP0, addr);
+ mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
+ addr = mfdcr(PLB4_ACR) | 0xa0000000; /* Was 0x8---- */
+ mtdcr(PLB4_ACR, addr); /* Sequoia */
/*
* As of errata version 0.4, CHIP_8: Incorrect Write to DDR SDRAM.
* Workaround: Disable write pipelining to DDR SDRAM by setting
* PLB0_ACR[WRP] = 0.
*/
- mtdcr(plb0_acr, 0); /* PATCH HAB: WRITE PIPELINING OFF */
+ mtdcr(PLB0_ACR, 0); /* PATCH HAB: WRITE PIPELINING OFF */
/* Segment1 */
- mtdcr(plb1_acr, 0); /* PATCH HAB: WRITE PIPELINING OFF */
+ mtdcr(PLB1_ACR, 0); /* PATCH HAB: WRITE PIPELINING OFF */
return board_with_pci();
}
diff --git a/board/netstal/hcu5/sdram.c b/board/netstal/hcu5/sdram.c
index 5c2ec35..0546cd7 100644
--- a/board/netstal/hcu5/sdram.c
+++ b/board/netstal/hcu5/sdram.c
@@ -89,11 +89,11 @@
/* -----------------------------------------------------------+
* Wait for the DCC master delay line to finish calibration
* ----------------------------------------------------------*/
- mtdcr(memcfga, DDR0_17);
+ mtdcr(SDRAM0_CFGADDR, DDR0_17);
val = DDR0_17_DLLLOCKREG_UNLOCKED;
while (wait != 0xffff) {
- val = mfdcr(memcfgd);
+ val = mfdcr(SDRAM0_CFGDATA);
if ((val & DDR0_17_DLLLOCKREG_MASK) ==
DDR0_17_DLLLOCKREG_LOCKED)
/* dlllockreg bit on */
diff --git a/board/netstal/mcu25/mcu25.c b/board/netstal/mcu25/mcu25.c
index 67c1b0b..9054282 100644
--- a/board/netstal/mcu25/mcu25.c
+++ b/board/netstal/mcu25/mcu25.c
@@ -71,8 +71,8 @@
mtdcr(uictr, 0x00000000); /* set int trigger levels */
mtdcr(uicsr, 0xFFFFFFFF); /* clear all ints */
- mtdcr(cntrl1, CPC0_CR1_VALUE);
- mtdcr(ecr, 0x60606000);
+ mtdcr(CPC0_CR1, CPC0_CR1_VALUE);
+ mtdcr(CPC0_ECR, 0x60606000);
mtdcr(CPC0_EIRR, 0x7C000000);
out32(GPIO0_OR, CONFIG_SYS_GPIO0_OR );
out32(GPIO0_TCR, CONFIG_SYS_GPIO0_TCR);
@@ -103,7 +103,7 @@
u16 index = boardVersReg & 0xf0;
/* Cannot be done in board_early_init */
- mtdcr(cntrl0, CPC0_CR0_VALUE);
+ mtdcr(CPC0_CR0, CPC0_CR0_VALUE);
/* Force /RTS to active. The board it not wired quite
* correctly to use cts/rtc flow control, so just force the
diff --git a/board/pcs440ep/pcs440ep.c b/board/pcs440ep/pcs440ep.c
index 47d6391..f966d02 100644
--- a/board/pcs440ep/pcs440ep.c
+++ b/board/pcs440ep/pcs440ep.c
@@ -143,9 +143,9 @@
/*--------------------------------------------------------------------
* Setup the external bus controller/chip selects
*-------------------------------------------------------------------*/
- mtdcr(ebccfga, xbcfg);
- reg = mfdcr(ebccfgd);
- mtdcr(ebccfgd, reg | 0x04000000); /* Set ATC */
+ mtdcr(EBC0_CFGADDR, EBC0_CFG);
+ reg = mfdcr(EBC0_CFGDATA);
+ mtdcr(EBC0_CFGDATA, reg | 0x04000000); /* Set ATC */
/*--------------------------------------------------------------------
* GPIO's are alreay setup in cpu/ppc4xx/cpu_init.c
@@ -174,10 +174,10 @@
/*--------------------------------------------------------------------
* Setup other serial configuration
*-------------------------------------------------------------------*/
- mfsdr(sdr_pci0, reg);
- mtsdr(sdr_pci0, 0x80000000 | reg); /* PCI arbiter enabled */
- mtsdr(sdr_pfc0, 0x00000000); /* Pin function: enable GPIO49-63 */
- mtsdr(sdr_pfc1, 0x00048000); /* Pin function: UART0 has 4 pins, select IRQ5 */
+ mfsdr(SDR0_PCI0, reg);
+ mtsdr(SDR0_PCI0, 0x80000000 | reg); /* PCI arbiter enabled */
+ mtsdr(SDR0_PFC0, 0x00000000); /* Pin function: enable GPIO49-63 */
+ mtsdr(SDR0_PFC1, 0x00048000); /* Pin function: UART0 has 4 pins, select IRQ5 */
return 0;
}
@@ -444,8 +444,8 @@
load_ethaddr();
/* Re-do sizing to get full correct info */
- mtdcr(ebccfga, pb0cr);
- pbcr = mfdcr(ebccfgd);
+ mtdcr(EBC0_CFGADDR, PB0CR);
+ pbcr = mfdcr(EBC0_CFGDATA);
switch (gd->bd->bi_flashsize) {
case 1 << 20:
size_val = 0;
@@ -473,8 +473,8 @@
break;
}
pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
- mtdcr(ebccfga, pb0cr);
- mtdcr(ebccfgd, pbcr);
+ mtdcr(EBC0_CFGADDR, PB0CR);
+ mtdcr(EBC0_CFGDATA, pbcr);
/* adjust flash start and offset */
gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
@@ -571,35 +571,35 @@
| Set priority for all PLB3 devices to 0.
| Set PLB3 arbiter to fair mode.
+-------------------------------------------------------------------------*/
- mfsdr(sdr_amp1, addr);
- mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(plb3_acr);
- mtdcr(plb3_acr, addr | 0x80000000);
+ mfsdr(SD0_AMP1, addr);
+ mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
+ addr = mfdcr(PLB3_ACR);
+ mtdcr(PLB3_ACR, addr | 0x80000000);
/*-------------------------------------------------------------------------+
| Set priority for all PLB4 devices to 0.
+-------------------------------------------------------------------------*/
- mfsdr(sdr_amp0, addr);
- mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(plb4_acr) | 0xa0000000; /* Was 0x8---- */
- mtdcr(plb4_acr, addr);
+ mfsdr(SD0_AMP0, addr);
+ mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
+ addr = mfdcr(PLB4_ACR) | 0xa0000000; /* Was 0x8---- */
+ mtdcr(PLB4_ACR, addr);
/*-------------------------------------------------------------------------+
| Set Nebula PLB4 arbiter to fair mode.
+-------------------------------------------------------------------------*/
/* Segment0 */
- addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair;
- addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled;
- addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep;
- addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep;
- mtdcr(plb0_acr, addr);
+ addr = (mfdcr(PLB0_ACR) & ~PLB0_ACR_PPM_MASK) | PLB0_ACR_PPM_FAIR;
+ addr = (addr & ~PLB0_ACR_HBU_MASK) | PLB0_ACR_HBU_ENABLED;
+ addr = (addr & ~PLB0_ACR_RDP_MASK) | PLB0_ACR_RDP_4DEEP;
+ addr = (addr & ~PLB0_ACR_WRP_MASK) | PLB0_ACR_WRP_2DEEP;
+ mtdcr(PLB0_ACR, addr);
/* Segment1 */
- addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair;
- addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled;
- addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep;
- addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep;
- mtdcr(plb1_acr, addr);
+ addr = (mfdcr(PLB1_ACR) & ~PLB1_ACR_PPM_MASK) | PLB1_ACR_PPM_FAIR;
+ addr = (addr & ~PLB1_ACR_HBU_MASK) | PLB1_ACR_HBU_ENABLED;
+ addr = (addr & ~PLB1_ACR_RDP_MASK) | PLB1_ACR_RDP_4DEEP;
+ addr = (addr & ~PLB1_ACR_WRP_MASK) | PLB1_ACR_WRP_2DEEP;
+ mtdcr(PLB1_ACR, addr);
return 1;
}
diff --git a/board/prodrive/alpr/alpr.c b/board/prodrive/alpr/alpr.c
index dc34319..be79b42 100644
--- a/board/prodrive/alpr/alpr.c
+++ b/board/prodrive/alpr/alpr.c
@@ -39,7 +39,7 @@
/*-------------------------------------------------------------------------
* Initialize EBC CONFIG
*-------------------------------------------------------------------------*/
- mtebc(xbcfg, EBC_CFG_LE_UNLOCK |
+ mtebc(EBC0_CFG, EBC_CFG_LE_UNLOCK |
EBC_CFG_PTD_DISABLE | EBC_CFG_RTC_64PERCLK |
EBC_CFG_ATC_PREVIOUS | EBC_CFG_DTC_PREVIOUS |
EBC_CFG_CTC_PREVIOUS | EBC_CFG_EMC_NONDEFAULT |
@@ -96,7 +96,7 @@
out32(GPIO0_ODR, in32(GPIO0_ODR) & ~(CONFIG_SYS_GPIO_SHUTDOWN | CONFIG_SYS_GPIO_SSD_EMPTY));
/* Setup GPIO/IRQ multiplexing */
- mtsdr(sdr_pfc0, 0x01a33e00);
+ mtsdr(SDR0_PFC0, 0x01a33e00);
return 0;
}
@@ -165,7 +165,7 @@
* The ocotea board is always configured as the host & requires the
* PCI arbiter to be enabled.
*--------------------------------------------------------------------------*/
- mfsdr(sdr_sdstp1, strap);
+ mfsdr(SDR0_SDSTP1, strap);
if( (strap & SDR0_SDSTP1_PAE_MASK) == 0 ){
printf("PCI: SDR0_STRP1[%08lX] - PCI Arbiter disabled.\n",strap);
return 0;
diff --git a/board/prodrive/p3p440/p3p440.c b/board/prodrive/p3p440/p3p440.c
index 1a0486f..18054e4 100644
--- a/board/prodrive/p3p440/p3p440.c
+++ b/board/prodrive/p3p440/p3p440.c
@@ -85,14 +85,14 @@
/*--------------------------------------------------------------------
* Setup the external bus controller/chip selects
*-------------------------------------------------------------------*/
- mtdcr(ebccfga, xbcfg);
- reg = mfdcr(ebccfgd);
- mtdcr(ebccfgd, reg | 0x04000000); /* Set ATC */
+ mtdcr(EBC0_CFGADDR, EBC0_CFG);
+ reg = mfdcr(EBC0_CFGDATA);
+ mtdcr(EBC0_CFGDATA, reg | 0x04000000); /* Set ATC */
/*--------------------------------------------------------------------
* Setup pin multiplexing (GPIO/IRQ...)
*-------------------------------------------------------------------*/
- mtdcr(cpc0_gpio, 0x03F01F80);
+ mtdcr(CPC0_GPIO, 0x03F01F80);
out32(GPIO0_ODR, 0x00000000); /* no open drain pins */
out32(GPIO0_TCR, CONFIG_SYS_GPIO_RDY | CONFIG_SYS_EREADY_IO | CONFIG_SYS_LED_RED | CONFIG_SYS_LED_GREEN);
@@ -153,12 +153,12 @@
* Check if only one FLASH bank is available
*/
if (gd->bd->bi_flashsize != CONFIG_SYS_MAX_FLASH_BANKS * (0 - CONFIG_SYS_FLASH0)) {
- mtebc(pb1cr, 0); /* disable cs */
- mtebc(pb1ap, 0);
- mtebc(pb2cr, 0); /* disable cs */
- mtebc(pb2ap, 0);
- mtebc(pb3cr, 0); /* disable cs */
- mtebc(pb3ap, 0);
+ mtebc(PB1CR, 0); /* disable cs */
+ mtebc(PB1AP, 0);
+ mtebc(PB2CR, 0); /* disable cs */
+ mtebc(PB2AP, 0);
+ mtebc(PB3CR, 0); /* disable cs */
+ mtebc(PB3AP, 0);
}
return 0;
@@ -185,7 +185,7 @@
* The P3P440 board is always configured as the host & requires the
* PCI arbiter to be disabled because it's an PMC module.
*--------------------------------------------------------------------------*/
- strap = mfdcr(cpc0_strp1);
+ strap = mfdcr(CPC0_STRP1);
if (strap & 0x00100000) {
printf("PCI: CPC0_STRP1[PAE] set.\n");
return 0;
diff --git a/board/sandburst/common/sb_common.c b/board/sandburst/common/sb_common.c
index b8160c8..d8b0564 100644
--- a/board/sandburst/common/sb_common.c
+++ b/board/sandburst/common/sb_common.c
@@ -322,7 +322,7 @@
* The metrobox is always configured as the host & requires the
* PCI arbiter to be enabled.
*--------------------------------------------------------------------------*/
- mfsdr(sdr_sdstp1, strap);
+ mfsdr(SDR0_SDSTP1, strap);
if( (strap & SDR0_SDSTP1_PAE_MASK) == 0 ){
printf("PCI: SDR0_STRP1[%08lX] - PCI Arbiter disabled.\n",strap);
return 0;
diff --git a/board/sandburst/karef/karef.c b/board/sandburst/karef/karef.c
index 92f5247..b80c206 100644
--- a/board/sandburst/karef/karef.c
+++ b/board/sandburst/karef/karef.c
@@ -67,7 +67,7 @@
ppc440_gpio_regs_t *gpio_regs;
/* Enable GPIO interrupts */
- mtsdr(sdr_pfc0, 0x00103E00);
+ mtsdr(SDR0_PFC0, 0x00103E00);
/* Setup access for LEDs, and system topology info */
gpio_regs = (ppc440_gpio_regs_t *)CONFIG_SYS_GPIO_BASE;
@@ -80,7 +80,7 @@
/*--------------------------------------------------------------------+
| Initialize EBC CONFIG
+-------------------------------------------------------------------*/
- mtebc(xbcfg,
+ mtebc(EBC0_CFG,
EBC_CFG_LE_UNLOCK | EBC_CFG_PTD_ENABLE |
EBC_CFG_RTC_64PERCLK | EBC_CFG_ATC_PREVIOUS |
EBC_CFG_DTC_PREVIOUS | EBC_CFG_CTC_PREVIOUS |
@@ -90,7 +90,7 @@
/*--------------------------------------------------------------------+
| 1/2 MB FLASH. Initialize bank 0 with default values.
+-------------------------------------------------------------------*/
- mtebc(pb0ap,
+ mtebc(PB0AP,
EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(8) |
EBC_BXAP_BCE_DISABLE | EBC_BXAP_CSN_ENCODE(1) |
EBC_BXAP_OEN_ENCODE(1)| EBC_BXAP_WBN_ENCODE(1) |
@@ -98,12 +98,12 @@
EBC_BXAP_RE_DISABLED | EBC_BXAP_BEM_WRITEONLY |
EBC_BXAP_PEN_DISABLED);
- mtebc(pb0cr, EBC_BXCR_BAS_ENCODE(CONFIG_SYS_FLASH_BASE) |
+ mtebc(PB0CR, EBC_BXCR_BAS_ENCODE(CONFIG_SYS_FLASH_BASE) |
EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_8BIT);
/*--------------------------------------------------------------------+
| 8KB NVRAM/RTC. Initialize bank 1 with default values.
+-------------------------------------------------------------------*/
- mtebc(pb1ap,
+ mtebc(PB1AP,
EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(10) |
EBC_BXAP_BCE_DISABLE | EBC_BXAP_CSN_ENCODE(1) |
EBC_BXAP_OEN_ENCODE(1)| EBC_BXAP_WBN_ENCODE(1) |
@@ -111,13 +111,13 @@
EBC_BXAP_RE_DISABLED | EBC_BXAP_BEM_WRITEONLY |
EBC_BXAP_PEN_DISABLED);
- mtebc(pb1cr, EBC_BXCR_BAS_ENCODE(0x48000000) |
+ mtebc(PB1CR, EBC_BXCR_BAS_ENCODE(0x48000000) |
EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_8BIT);
/*--------------------------------------------------------------------+
| Compact Flash, uses 2 Chip Selects (2 & 6)
+-------------------------------------------------------------------*/
- mtebc(pb2ap,
+ mtebc(PB2AP,
EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(8) |
EBC_BXAP_BCE_DISABLE | EBC_BXAP_CSN_ENCODE(1) |
EBC_BXAP_OEN_ENCODE(1)| EBC_BXAP_WBN_ENCODE(1) |
@@ -125,40 +125,40 @@
EBC_BXAP_RE_DISABLED | EBC_BXAP_BEM_WRITEONLY |
EBC_BXAP_PEN_DISABLED);
- mtebc(pb2cr, EBC_BXCR_BAS_ENCODE(0xF0000000) |
+ mtebc(PB2CR, EBC_BXCR_BAS_ENCODE(0xF0000000) |
EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_16BIT);
/*--------------------------------------------------------------------+
| KaRef Scan FPGA. Initialize bank 3 with default values.
+-------------------------------------------------------------------*/
- mtebc(pb5ap,
+ mtebc(PB5AP,
EBC_BXAP_RE_ENABLED | EBC_BXAP_SOR_NONDELAYED |
EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(3) |
EBC_BXAP_TH_ENCODE(1) | EBC_BXAP_WBF_ENCODE(0) |
EBC_BXAP_CSN_ENCODE(1) | EBC_BXAP_PEN_DISABLED |
EBC_BXAP_OEN_ENCODE(1) | EBC_BXAP_BEM_RW);
- mtebc(pb5cr, EBC_BXCR_BAS_ENCODE(0x48200000) |
+ mtebc(PB5CR, EBC_BXCR_BAS_ENCODE(0x48200000) |
EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_32BIT);
/*--------------------------------------------------------------------+
| MAC A & B for Kamino. OFEM FPGA decodes the addresses
| Initialize bank 4 with default values.
+-------------------------------------------------------------------*/
- mtebc(pb4ap,
+ mtebc(PB4AP,
EBC_BXAP_RE_ENABLED | EBC_BXAP_SOR_NONDELAYED |
EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(3) |
EBC_BXAP_TH_ENCODE(1) | EBC_BXAP_WBF_ENCODE(0) |
EBC_BXAP_CSN_ENCODE(1) | EBC_BXAP_PEN_DISABLED |
EBC_BXAP_OEN_ENCODE(1) | EBC_BXAP_BEM_RW);
- mtebc(pb4cr, EBC_BXCR_BAS_ENCODE(0x48600000) |
+ mtebc(PB4CR, EBC_BXCR_BAS_ENCODE(0x48600000) |
EBC_BXCR_BS_2MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_32BIT);
/*--------------------------------------------------------------------+
| OFEM FPGA Initialize bank 5 with default values.
+-------------------------------------------------------------------*/
- mtebc(pb3ap,
+ mtebc(PB3AP,
EBC_BXAP_RE_ENABLED | EBC_BXAP_SOR_NONDELAYED |
EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(3) |
EBC_BXAP_TH_ENCODE(1) | EBC_BXAP_WBF_ENCODE(0) |
@@ -166,14 +166,14 @@
EBC_BXAP_OEN_ENCODE(1) | EBC_BXAP_BEM_RW);
- mtebc(pb3cr, EBC_BXCR_BAS_ENCODE(0x48400000) |
+ mtebc(PB3CR, EBC_BXCR_BAS_ENCODE(0x48400000) |
EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_32BIT);
/*--------------------------------------------------------------------+
| Compact Flash, uses 2 Chip Selects (2 & 6)
+-------------------------------------------------------------------*/
- mtebc(pb6ap,
+ mtebc(PB6AP,
EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(8) |
EBC_BXAP_BCE_DISABLE | EBC_BXAP_CSN_ENCODE(1) |
EBC_BXAP_OEN_ENCODE(1)| EBC_BXAP_WBN_ENCODE(1) |
@@ -181,20 +181,20 @@
EBC_BXAP_RE_DISABLED | EBC_BXAP_BEM_WRITEONLY |
EBC_BXAP_PEN_DISABLED);
- mtebc(pb6cr, EBC_BXCR_BAS_ENCODE(0xF0100000) |
+ mtebc(PB6CR, EBC_BXCR_BAS_ENCODE(0xF0100000) |
EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_16BIT);
/*--------------------------------------------------------------------+
| BME-32. Initialize bank 7 with default values.
+-------------------------------------------------------------------*/
- mtebc(pb7ap,
+ mtebc(PB7AP,
EBC_BXAP_RE_ENABLED | EBC_BXAP_SOR_NONDELAYED |
EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(3) |
EBC_BXAP_TH_ENCODE(1) | EBC_BXAP_WBF_ENCODE(0) |
EBC_BXAP_CSN_ENCODE(1) | EBC_BXAP_PEN_DISABLED |
EBC_BXAP_OEN_ENCODE(1) | EBC_BXAP_BEM_RW);
- mtebc(pb7cr, EBC_BXCR_BAS_ENCODE(0x48500000) |
+ mtebc(PB7CR, EBC_BXCR_BAS_ENCODE(0x48500000) |
EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_32BIT);
/*--------------------------------------------------------------------+
diff --git a/board/sandburst/metrobox/metrobox.c b/board/sandburst/metrobox/metrobox.c
index 27d7f74..ad3f9bc 100644
--- a/board/sandburst/metrobox/metrobox.c
+++ b/board/sandburst/metrobox/metrobox.c
@@ -57,7 +57,7 @@
ppc440_gpio_regs_t *gpio_regs;
/* Enable GPIO interrupts */
- mtsdr(sdr_pfc0, 0x00103E00);
+ mtsdr(SDR0_PFC0, 0x00103E00);
/* Setup access for LEDs, and system topology info */
gpio_regs = (ppc440_gpio_regs_t *)CONFIG_SYS_GPIO_BASE;
@@ -70,7 +70,7 @@
/*--------------------------------------------------------------------+
| Initialize EBC CONFIG
+-------------------------------------------------------------------*/
- mtebc(xbcfg,
+ mtebc(EBC0_CFG,
EBC_CFG_LE_UNLOCK | EBC_CFG_PTD_ENABLE |
EBC_CFG_RTC_64PERCLK | EBC_CFG_ATC_PREVIOUS |
EBC_CFG_DTC_PREVIOUS | EBC_CFG_CTC_PREVIOUS |
@@ -80,7 +80,7 @@
/*--------------------------------------------------------------------+
| 1/2 MB FLASH. Initialize bank 0 with default values.
+-------------------------------------------------------------------*/
- mtebc(pb0ap,
+ mtebc(PB0AP,
EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(8) |
EBC_BXAP_BCE_DISABLE | EBC_BXAP_CSN_ENCODE(1) |
EBC_BXAP_OEN_ENCODE(1)| EBC_BXAP_WBN_ENCODE(1) |
@@ -88,12 +88,12 @@
EBC_BXAP_RE_DISABLED | EBC_BXAP_BEM_WRITEONLY |
EBC_BXAP_PEN_DISABLED);
- mtebc(pb0cr, EBC_BXCR_BAS_ENCODE(CONFIG_SYS_FLASH_BASE) |
+ mtebc(PB0CR, EBC_BXCR_BAS_ENCODE(CONFIG_SYS_FLASH_BASE) |
EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_8BIT);
/*--------------------------------------------------------------------+
| 8KB NVRAM/RTC. Initialize bank 1 with default values.
+-------------------------------------------------------------------*/
- mtebc(pb1ap,
+ mtebc(PB1AP,
EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(10) |
EBC_BXAP_BCE_DISABLE | EBC_BXAP_CSN_ENCODE(1) |
EBC_BXAP_OEN_ENCODE(1)| EBC_BXAP_WBN_ENCODE(1) |
@@ -101,13 +101,13 @@
EBC_BXAP_RE_DISABLED | EBC_BXAP_BEM_WRITEONLY |
EBC_BXAP_PEN_DISABLED);
- mtebc(pb1cr, EBC_BXCR_BAS_ENCODE(0x48000000) |
+ mtebc(PB1CR, EBC_BXCR_BAS_ENCODE(0x48000000) |
EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_8BIT);
/*--------------------------------------------------------------------+
| Compact Flash, uses 2 Chip Selects (2 & 6)
+-------------------------------------------------------------------*/
- mtebc(pb2ap,
+ mtebc(PB2AP,
EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(8) |
EBC_BXAP_BCE_DISABLE | EBC_BXAP_CSN_ENCODE(1) |
EBC_BXAP_OEN_ENCODE(1)| EBC_BXAP_WBN_ENCODE(1) |
@@ -115,20 +115,20 @@
EBC_BXAP_RE_DISABLED | EBC_BXAP_BEM_WRITEONLY |
EBC_BXAP_PEN_DISABLED);
- mtebc(pb2cr, EBC_BXCR_BAS_ENCODE(0xF0000000) |
+ mtebc(PB2CR, EBC_BXCR_BAS_ENCODE(0xF0000000) |
EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_16BIT);
/*--------------------------------------------------------------------+
| OPTO & OFEM FPGA. Initialize bank 3 with default values.
+-------------------------------------------------------------------*/
- mtebc(pb3ap,
+ mtebc(PB3AP,
EBC_BXAP_RE_ENABLED | EBC_BXAP_SOR_NONDELAYED |
EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(3) |
EBC_BXAP_TH_ENCODE(1) | EBC_BXAP_WBF_ENCODE(0) |
EBC_BXAP_CSN_ENCODE(1) | EBC_BXAP_PEN_DISABLED |
EBC_BXAP_OEN_ENCODE(1) | EBC_BXAP_BEM_RW);
- mtebc(pb3cr, EBC_BXCR_BAS_ENCODE(0x48200000) |
+ mtebc(PB3CR, EBC_BXCR_BAS_ENCODE(0x48200000) |
EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_32BIT);
/*--------------------------------------------------------------------+
@@ -136,34 +136,34 @@
| MAC A & B for Kamino. OFEM FPGA decodes the addresses
| Initialize bank 4 with default values.
+-------------------------------------------------------------------*/
- mtebc(pb4ap,
+ mtebc(PB4AP,
EBC_BXAP_RE_ENABLED | EBC_BXAP_SOR_NONDELAYED |
EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(3) |
EBC_BXAP_TH_ENCODE(1) | EBC_BXAP_WBF_ENCODE(0) |
EBC_BXAP_CSN_ENCODE(1) | EBC_BXAP_PEN_DISABLED |
EBC_BXAP_OEN_ENCODE(1) | EBC_BXAP_BEM_RW);
- mtebc(pb4cr, EBC_BXCR_BAS_ENCODE(0x48600000) |
+ mtebc(PB4CR, EBC_BXCR_BAS_ENCODE(0x48600000) |
EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_32BIT);
/*--------------------------------------------------------------------+
| Metrobox MAC B Initialize bank 5 with default values.
| KA REF FPGA Initialize bank 5 with default values.
+-------------------------------------------------------------------*/
- mtebc(pb5ap,
+ mtebc(PB5AP,
EBC_BXAP_RE_ENABLED | EBC_BXAP_SOR_NONDELAYED |
EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(3) |
EBC_BXAP_TH_ENCODE(1) | EBC_BXAP_WBF_ENCODE(0) |
EBC_BXAP_CSN_ENCODE(1) | EBC_BXAP_PEN_DISABLED |
EBC_BXAP_OEN_ENCODE(1) | EBC_BXAP_BEM_RW);
- mtebc(pb5cr, EBC_BXCR_BAS_ENCODE(0x48700000) |
+ mtebc(PB5CR, EBC_BXCR_BAS_ENCODE(0x48700000) |
EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_32BIT);
/*--------------------------------------------------------------------+
| Compact Flash, uses 2 Chip Selects (2 & 6)
+-------------------------------------------------------------------*/
- mtebc(pb6ap,
+ mtebc(PB6AP,
EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(8) |
EBC_BXAP_BCE_DISABLE | EBC_BXAP_CSN_ENCODE(1) |
EBC_BXAP_OEN_ENCODE(1)| EBC_BXAP_WBN_ENCODE(1) |
@@ -171,20 +171,20 @@
EBC_BXAP_RE_DISABLED | EBC_BXAP_BEM_WRITEONLY |
EBC_BXAP_PEN_DISABLED);
- mtebc(pb6cr, EBC_BXCR_BAS_ENCODE(0xF0100000) |
+ mtebc(PB6CR, EBC_BXCR_BAS_ENCODE(0xF0100000) |
EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_16BIT);
/*--------------------------------------------------------------------+
| BME-32. Initialize bank 7 with default values.
+-------------------------------------------------------------------*/
- mtebc(pb7ap,
+ mtebc(PB7AP,
EBC_BXAP_RE_ENABLED | EBC_BXAP_SOR_NONDELAYED |
EBC_BXAP_BME_DISABLED | EBC_BXAP_TWT_ENCODE(3) |
EBC_BXAP_TH_ENCODE(1) | EBC_BXAP_WBF_ENCODE(0) |
EBC_BXAP_CSN_ENCODE(1) | EBC_BXAP_PEN_DISABLED |
EBC_BXAP_OEN_ENCODE(1) | EBC_BXAP_BEM_RW);
- mtebc(pb7cr, EBC_BXCR_BAS_ENCODE(0x48500000) |
+ mtebc(PB7CR, EBC_BXCR_BAS_ENCODE(0x48500000) |
EBC_BXCR_BS_1MB | EBC_BXCR_BU_RW | EBC_BXCR_BW_32BIT);
/*--------------------------------------------------------------------+
diff --git a/board/sbc405/sbc405.c b/board/sbc405/sbc405.c
index 7818cd7..66842ea 100644
--- a/board/sbc405/sbc405.c
+++ b/board/sbc405/sbc405.c
@@ -52,7 +52,7 @@
/*
* EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us
*/
- mtebc (epcr, 0xa8400000);
+ mtebc (EBC0_CFG, 0xa8400000);
return 0;
}
diff --git a/board/sc3/init.S b/board/sc3/init.S
index f97a5ea..6052c66 100644
--- a/board/sc3/init.S
+++ b/board/sc3/init.S
@@ -58,7 +58,7 @@
* We need the current boot up configuration to set correct
* timings into internal flash and external flash
*/
- mfdcr r24,strap /* xxxx xxxx xxxx xxx? ?xxx xxxx xxxx xxxx
+ mfdcr r24,CPC0_PSR /* xxxx xxxx xxxx xxx? ?xxx xxxx xxxx xxxx
0 0 -> 8 bit external ROM
0 1 -> 16 bit internal ROM */
addi r4,0,2
@@ -113,8 +113,8 @@
* We only have to change the timing. Mapping is ok by boot-strapping
*----------------------------------------------------------------------- */
- li r4,pb0ap /* PB0AP=Peripheral Bank 0 Access Parameters */
- mtdcr ebccfga,r4
+ li r4,PB1AP /* PB0AP=Peripheral Bank 0 Access Parameters */
+ mtdcr EBC0_CFGADDR,r4
mr r4,r26 /* assume internal fast flash is boot flash */
cmpwi r24,0x2000 /* assumption true? ... */
@@ -122,27 +122,27 @@
mr r4,r25 /* ...no, use the slow variant */
mr r25,r26 /* use this for the other flash */
1:
- mtdcr ebccfgd,r4 /* change timing now */
+ mtdcr EBC0_CFGDATA,r4 /* change timing now */
- li r4,pb0cr /* PB0CR=Peripheral Bank 0 Control Register */
- mtdcr ebccfga,r4
- mfdcr r4,ebccfgd
+ li r4,PB0CR /* PB0CR=Peripheral Bank 0 Control Register */
+ mtdcr EBC0_CFGADDR,r4
+ mfdcr r4,EBC0_CFGDATA
lis r3,0x0001
ori r3,r3,0x8000 /* allow reads and writes */
or r4,r4,r3
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
/*-----------------------------------------------------------------------
* Memory Bank 3 (Second-Flash) initialization
* 0xF0000000...0xF01FFFFF -> 2MB
*----------------------------------------------------------------------- */
- li r4,pb3ap /* Peripheral Bank 1 Access Parameter */
- mtdcr ebccfga,r4
- mtdcr ebccfgd,r2 /* change timing */
+ li r4,PB3AP /* Peripheral Bank 1 Access Parameter */
+ mtdcr EBC0_CFGADDR,r4
+ mtdcr EBC0_CFGDATA,r2 /* change timing */
- li r4,pb3cr /* Peripheral Bank 1 Configuration Registers */
- mtdcr ebccfga,r4
+ li r4,PB3CR /* Peripheral Bank 1 Configuration Registers */
+ mtdcr EBC0_CFGADDR,r4
lis r4,0xF003
ori r4,r4,0x8000
@@ -151,7 +151,7 @@
*/
xori r24,r24,0x2000 /* invert current bus width */
or r4,r4,r24
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
/*-----------------------------------------------------------------------
* Memory Bank 1 (NAND-Flash) initialization
@@ -169,28 +169,28 @@
* ----> 2 clocks per cycle = 60ns cycle (30ns active, 30ns hold)
*----------------------------------------------------------------------- */
- li r4,pb1ap /* Peripheral Bank 1 Access Parameter */
- mtdcr ebccfga,r4
+ li r4,PB1AP /* Peripheral Bank 1 Access Parameter */
+ mtdcr EBC0_CFGADDR,r4
lis r4,0x0000
ori r4,r4,0x0200
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
- li r4,pb1cr /* Peripheral Bank 1 Configuration Registers */
- mtdcr ebccfga,r4
+ li r4,PB1CR /* Peripheral Bank 1 Configuration Registers */
+ mtdcr EBC0_CFGADDR,r4
lis r4,0x77D1
ori r4,r4,0x8000
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
/* USB init (without acceleration) */
#ifndef CONFIG_ISP1161_PRESENT
- li r4,pb4ap /* PB4AP=Peripheral Bank 4 Access Parameters */
- mtdcr ebccfga,r4
+ li r4,PB4AP /* PB4AP=Peripheral Bank 4 Access Parameters */
+ mtdcr EBC0_CFGADDR,r4
lis r4,0x0180
ori r4,r4,0x5940
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
#endif
/*-----------------------------------------------------------------------
@@ -204,8 +204,8 @@
A7/A24=0 -> memory cycle
A7/ /A24=1 -> I/O cycle
*/
- li r4,pb2ap /* PB2AP=Peripheral Bank 2 Access Parameters */
- mtdcr ebccfga,r4
+ li r4,PB2AP /* PB2AP=Peripheral Bank 2 Access Parameters */
+ mtdcr EBC0_CFGADDR,r4
/*
We emulate an ISA access
@@ -226,58 +226,58 @@
lis r4,0x0100
ori r4,r4,0x0340
#endif
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
#ifdef IDE_USES_ISA_EMULATION
- li r25,pb5ap /* PB5AP=Peripheral Bank 5 Access Parameters */
- mtdcr ebccfga,r25
- mtdcr ebccfgd,r4
+ li r25,PB5AP /* PB5AP=Peripheral Bank 5 Access Parameters */
+ mtdcr EBC0_CFGADDR,r25
+ mtdcr EBC0_CFGDATA,r4
#endif
- li r25,pb6ap /* PB6AP=Peripheral Bank 6 Access Parameters */
- mtdcr ebccfga,r25
- mtdcr ebccfgd,r4
- li r25,pb7ap /* PB7AP=Peripheral Bank 7 Access Parameters */
- mtdcr ebccfga,r25
- mtdcr ebccfgd,r4
+ li r25,PB6AP /* PB6AP=Peripheral Bank 6 Access Parameters */
+ mtdcr EBC0_CFGADDR,r25
+ mtdcr EBC0_CFGDATA,r4
+ li r25,PB7AP /* PB7AP=Peripheral Bank 7 Access Parameters */
+ mtdcr EBC0_CFGADDR,r25
+ mtdcr EBC0_CFGDATA,r4
- li r25,pb2cr /* PB2CR=Peripheral Bank 2 Configuration Register */
- mtdcr ebccfga,r25
+ li r25,PB2CR /* PB2CR=Peripheral Bank 2 Configuration Register */
+ mtdcr EBC0_CFGADDR,r25
lis r4,0x780B
ori r4,r4,0xA000
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
/*
* the other areas are only 1MiB in size
*/
lis r4,0x7401
ori r4,r4,0xA000
- li r25,pb6cr /* PB6CR=Peripheral Bank 6 Configuration Register */
- mtdcr ebccfga,r25
+ li r25,PB6CR /* PB6CR=Peripheral Bank 6 Configuration Register */
+ mtdcr EBC0_CFGADDR,r25
lis r4,0x7401
ori r4,r4,0xA000
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
- li r25,pb7cr /* PB7CR=Peripheral Bank 7 Configuration Register */
- mtdcr ebccfga,r25
+ li r25,PB7CR /* PB7CR=Peripheral Bank 7 Configuration Register */
+ mtdcr EBC0_CFGADDR,r25
lis r4,0x7411
ori r4,r4,0xA000
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
#ifndef CONFIG_ISP1161_PRESENT
- li r25,pb4cr /* PB4CR=Peripheral Bank 4 Configuration Register */
- mtdcr ebccfga,r25
+ li r25,PB4CR /* PB4CR=Peripheral Bank 4 Configuration Register */
+ mtdcr EBC0_CFGADDR,r25
lis r4,0x7421
ori r4,r4,0xA000
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
#endif
#ifdef IDE_USES_ISA_EMULATION
- li r25,pb5cr /* PB5CR=Peripheral Bank 5 Configuration Register */
- mtdcr ebccfga,r25
+ li r25,PB5CR /* PB5CR=Peripheral Bank 5 Configuration Register */
+ mtdcr EBC0_CFGADDR,r25
lis r4,0x0000
ori r4,r4,0x0000
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
#endif
/*-----------------------------------------------------------------------
@@ -315,19 +315,19 @@
#ifdef CONFIG_ISP1161_PRESENT
- li r4,pb4ap /* PB4AP=Peripheral Bank 4 Access Parameters */
- mtdcr ebccfga,r4
+ li r4,PB4AP /* PB4AP=Peripheral Bank 4 Access Parameters */
+ mtdcr EBC0_CFGADDR,r4
lis r4,0x030D
ori r4,r4,0x5E80
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
- li r4,pb4cr /* PB2CR=Peripheral Bank 4 Configuration Register */
- mtdcr ebccfga,r4
+ li r4,PB4CR /* PB2CR=Peripheral Bank 4 Configuration Register */
+ mtdcr EBC0_CFGADDR,r4
lis r4,0x77C1
ori r4,r4,0xA000
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
#endif
@@ -352,28 +352,28 @@
*
*----------------------------------------------------------------------- */
- li r4,pb5ap
- mtdcr ebccfga,r4
+ li r4,PB5AP
+ mtdcr EBC0_CFGADDR,r4
lis r4,0x040C
ori r4,r4,0x0200
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
- li r4,pb5cr /* PB2CR=Peripheral Bank 2 Configuration Register */
- mtdcr ebccfga,r4
+ li r4,PB5CR /* PB2CR=Peripheral Bank 2 Configuration Register */
+ mtdcr EBC0_CFGADDR,r4
lis r4,0x7A01
ori r4,r4,0xA000
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
#endif
/*
* External Peripheral Control Register
*/
- li r4,epcr
- mtdcr ebccfga,r4
+ li r4,EBC0_CFG
+ mtdcr EBC0_CFGADDR,r4
lis r4,0xB84E
ori r4,r4,0xF000
- mtdcr ebccfgd,r4
+ mtdcr EBC0_CFGDATA,r4
/*
* drive POST code
*/
diff --git a/board/sc3/sc3.c b/board/sc3/sc3.c
index 6c82fe7..5ae7b12 100644
--- a/board/sc3/sc3.c
+++ b/board/sc3/sc3.c
@@ -199,14 +199,14 @@
static int sc3_cameron_init (void)
{
/* Set up the Memory Controller for the CAMERON version */
- mtebc (pb4ap, 0x01805940);
- mtebc (pb4cr, 0x7401a000);
- mtebc (pb5ap, 0x01805940);
- mtebc (pb5cr, 0x7401a000);
- mtebc (pb6ap, 0x0);
- mtebc (pb6cr, 0x0);
- mtebc (pb7ap, 0x0);
- mtebc (pb7cr, 0x0);
+ mtebc (PB4AP, 0x01805940);
+ mtebc (PB4CR, 0x7401a000);
+ mtebc (PB5AP, 0x01805940);
+ mtebc (PB5CR, 0x7401a000);
+ mtebc (PB6AP, 0x0);
+ mtebc (PB6CR, 0x0);
+ mtebc (PB7AP, 0x0);
+ mtebc (PB7CR, 0x0);
return 0;
}
@@ -312,18 +312,18 @@
mtdcr (uicsr, 0xFFFFFFFF); /* clear all ints */
/* setup other implementation specific details */
- mtdcr (ecr, 0x60606000);
+ mtdcr (CPC0_ECR, 0x60606000);
- mtdcr (cntrl1, 0x000042C0);
+ mtdcr (CPC0_CR1, 0x000042C0);
if (IS_CAMERON) {
- mtdcr (cntrl0, 0x01380000);
+ mtdcr (CPC0_CR0, 0x01380000);
/* Setup the GPIOs */
writel (0x08008000, 0xEF600700); /* Output states */
writel (0x00000000, 0xEF600718); /* Open Drain control */
writel (0x68098000, 0xEF600704); /* Output control */
} else {
- mtdcr (cntrl0,0x00080000);
+ mtdcr (CPC0_CR0,0x00080000);
/* Setup the GPIOs */
writel (0x08000000, 0xEF600700); /* Output states */
writel (0x14000000, 0xEF600718); /* Open Drain control */
@@ -331,13 +331,13 @@
}
/* Code decompression disabled */
- mtdcr (kiar, kconf);
- mtdcr (kidr, 0x2B);
+ mtdcr (KIAR, KCONF);
+ mtdcr (KIDR, 0x2B);
/* CPC0_ER: enable sleep mode of (currently) unused components */
/* CPC0_FR: force unused components into sleep mode */
- mtdcr (cpmer, 0x3F800000);
- mtdcr (cpmfr, 0x14000000);
+ mtdcr (CPMER, 0x3F800000);
+ mtdcr (CPMFR, 0x14000000);
/* set PLB priority */
mtdcr (0x87, 0x08000000);
@@ -472,19 +472,19 @@
#ifdef SC3_DEBUGOUT
-static unsigned int ap[] = {pb0ap, pb1ap, pb2ap, pb3ap, pb4ap,
- pb5ap, pb6ap, pb7ap};
-static unsigned int cr[] = {pb0cr, pb1cr, pb2cr, pb3cr, pb4cr,
- pb5cr, pb6cr, pb7cr};
+static unsigned int ap[] = {PB0AP, PB1AP, PB2AP, PB3AP, PB4AP,
+ PB5AP, PB6AP, PB7AP};
+static unsigned int cr[] = {PB0CR, PB1CR, PB2CR, PB3CR, PB4CR,
+ PB5CR, PB6CR, PB7CR};
static int show_reg (int nr)
{
unsigned long ul1, ul2;
- mtdcr (ebccfga, ap[nr]);
- ul1 = mfdcr (ebccfgd);
- mtdcr (ebccfga, cr[nr]);
- ul2 = mfdcr(ebccfgd);
+ mtdcr (EBC0_CFGADDR, ap[nr]);
+ ul1 = mfdcr (EBC0_CFGDATA);
+ mtdcr (EBC0_CFGADDR, cr[nr]);
+ ul2 = mfdcr(EBC0_CFGDATA);
printCSConfig(nr, ul1, ul2);
return 0;
}
@@ -500,8 +500,8 @@
show_reg (i);
}
- mtdcr (ebccfga, epcr);
- ul1 = mfdcr (ebccfgd);
+ mtdcr (EBC0_CFGADDR, EBC0_CFG);
+ ul1 = mfdcr (EBC0_CFGDATA);
puts ("\nGeneral configuration:\n");
@@ -591,21 +591,21 @@
puts("\nSDRAM configuration:\n");
- mtdcr (memcfga, mem_mcopt1);
- ul1 = mfdcr(memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_mcopt1);
+ ul1 = mfdcr(SDRAM0_CFGDATA);
if (!(ul1 & 0x80000000)) {
puts(" Controller disabled\n");
return 0;
}
for (i = 0; i < 4; i++) {
- mtdcr (memcfga, mbcf[i]);
- ul1 = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mbcf[i]);
+ ul1 = mfdcr (SDRAM0_CFGDATA);
mems += printSDRAMConfig (i, ul1);
}
- mtdcr (memcfga, mem_sdtr1);
- ul1 = mfdcr(memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_sdtr1);
+ ul1 = mfdcr(SDRAM0_CFGDATA);
printf ("Timing:\n -CAS latency %lu\n", ((ul1 & 0x1800000) >> 23)+1);
printf (" -Precharge %lu (PTA) \n", ((ul1 & 0xC0000) >> 18) + 1);
@@ -614,15 +614,15 @@
printf (" -CAS to RAS %lu\n", ((ul1 & 0x1C) >> 2) + 4);
printf (" -RAS to CAS %lu\n", ((ul1 & 0x3) + 1));
puts ("Misc:\n");
- mtdcr (memcfga, mem_rtr);
- ul1 = mfdcr(memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_rtr);
+ ul1 = mfdcr(SDRAM0_CFGDATA);
printf (" -Refresh rate: %luns\n", (ul1 >> 16) * 7);
- mtdcr(memcfga,mem_pmit);
- ul2=mfdcr(memcfgd);
+ mtdcr(SDRAM0_CFGADDR,mem_pmit);
+ ul2=mfdcr(SDRAM0_CFGDATA);
- mtdcr(memcfga,mem_mcopt1);
- ul1=mfdcr(memcfgd);
+ mtdcr(SDRAM0_CFGADDR,mem_mcopt1);
+ ul1=mfdcr(SDRAM0_CFGDATA);
if (ul1 & 0x20000000)
printf(" -Power Down after: %luns\n",
@@ -658,8 +658,8 @@
else
puts(" -Memory lines only at write cycles active outputs\n");
- mtdcr (memcfga, mem_status);
- ul1 = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_status);
+ ul1 = mfdcr (SDRAM0_CFGDATA);
if (ul1 & 0x80000000)
puts(" -SDRAM Controller ready\n");
else
@@ -670,20 +670,20 @@
return (mems * 1024 * 1024);
#else
- mtdcr (memcfga, mem_mb0cf);
- ul1 = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_mb0cf);
+ ul1 = mfdcr (SDRAM0_CFGDATA);
mems = printSDRAMConfig (0, ul1);
- mtdcr (memcfga, mem_mb1cf);
- ul1 = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_mb1cf);
+ ul1 = mfdcr (SDRAM0_CFGDATA);
mems += printSDRAMConfig (1, ul1);
- mtdcr (memcfga, mem_mb2cf);
- ul1 = mfdcr(memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_mb2cf);
+ ul1 = mfdcr(SDRAM0_CFGDATA);
mems += printSDRAMConfig (2, ul1);
- mtdcr (memcfga, mem_mb3cf);
- ul1 = mfdcr(memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_mb3cf);
+ ul1 = mfdcr(SDRAM0_CFGDATA);
mems += printSDRAMConfig (3, ul1);
return (mems * 1024 * 1024);
diff --git a/board/snmc/qs850/flash.c b/board/snmc/qs850/flash.c
index 9e276a1..a26a679 100644
--- a/board/snmc/qs850/flash.c
+++ b/board/snmc/qs850/flash.c
@@ -104,21 +104,21 @@
/* Re-do sizing to get full correct info */
if (size_b1) {
- mtdcr(ebccfga, pb0cr);
- pbcr = mfdcr(ebccfgd);
- mtdcr(ebccfga, pb0cr);
+ mtdcr(EBC0_CFGADDR, PB0CR);
+ pbcr = mfdcr(EBC0_CFGDATA);
+ mtdcr(EBC0_CFGADDR, PB0CR);
base_b1 = -size_b1;
pbcr = (pbcr & 0x0001ffff) | base_b1 | (((size_b1/1024/1024)-1)<<17);
- mtdcr(ebccfgd, pbcr);
+ mtdcr(EBC0_CFGDATA, pbcr);
}
if (size_b0) {
- mtdcr(ebccfga, pb1cr);
- pbcr = mfdcr(ebccfgd);
- mtdcr(ebccfga, pb1cr);
+ mtdcr(EBC0_CFGADDR, PB1CR);
+ pbcr = mfdcr(EBC0_CFGDATA);
+ mtdcr(EBC0_CFGADDR, PB1CR);
base_b0 = base_b1 - size_b0;
pbcr = (pbcr & 0x0001ffff) | base_b0 | (((size_b0/1024/1024)-1)<<17);
- mtdcr(ebccfgd, pbcr);
+ mtdcr(EBC0_CFGDATA, pbcr);
}
size_b0 = flash_get_size((volatile FLASH_WORD_SIZE *)base_b0, &flash_info[0]);
diff --git a/board/snmc/qs860t/flash.c b/board/snmc/qs860t/flash.c
index 2cb8dcb..48c2258 100644
--- a/board/snmc/qs860t/flash.c
+++ b/board/snmc/qs860t/flash.c
@@ -102,21 +102,21 @@
/* Re-do sizing to get full correct info */
if (size_b1) {
- mtdcr(ebccfga, pb0cr);
- pbcr = mfdcr(ebccfgd);
- mtdcr(ebccfga, pb0cr);
+ mtdcr(EBC0_CFGADDR, PB0CR);
+ pbcr = mfdcr(EBC0_CFGDATA);
+ mtdcr(EBC0_CFGADDR, PB0CR);
base_b1 = -size_b1;
pbcr = (pbcr & 0x0001ffff) | base_b1 | (((size_b1/1024/1024)-1)<<17);
- mtdcr(ebccfgd, pbcr);
+ mtdcr(EBC0_CFGDATA, pbcr);
}
if (size_b0) {
- mtdcr(ebccfga, pb1cr);
- pbcr = mfdcr(ebccfgd);
- mtdcr(ebccfga, pb1cr);
+ mtdcr(EBC0_CFGADDR, PB1CR);
+ pbcr = mfdcr(EBC0_CFGDATA);
+ mtdcr(EBC0_CFGADDR, PB1CR);
base_b0 = base_b1 - size_b0;
pbcr = (pbcr & 0x0001ffff) | base_b0 | (((size_b0/1024/1024)-1)<<17);
- mtdcr(ebccfgd, pbcr);
+ mtdcr(EBC0_CFGDATA, pbcr);
}
size_b0 = flash_get_size((volatile FLASH_WORD_SIZE *)base_b0, &flash_info[0]);
diff --git a/board/tb0229/flash.c b/board/tb0229/flash.c
index 933d5ec..1554642 100644
--- a/board/tb0229/flash.c
+++ b/board/tb0229/flash.c
@@ -108,25 +108,25 @@
/* Re-do sizing to get full correct info */
if (size_b1) {
- mtdcr (ebccfga, pb0cr);
- pbcr = mfdcr (ebccfgd);
- mtdcr (ebccfga, pb0cr);
+ mtdcr (EBC0_CFGADDR, PB0CR);
+ pbcr = mfdcr (EBC0_CFGDATA);
+ mtdcr (EBC0_CFGADDR, PB0CR);
base_b1 = -size_b1;
pbcr = (pbcr & 0x0001ffff) | base_b1 |
(((size_b1 / 1024 / 1024) - 1) << 17);
- mtdcr (ebccfgd, pbcr);
- /* printf("pb1cr = %x\n", pbcr); */
+ mtdcr (EBC0_CFGDATA, pbcr);
+ /* printf("PB1CR = %x\n", pbcr); */
}
if (size_b0) {
- mtdcr (ebccfga, pb1cr);
- pbcr = mfdcr (ebccfgd);
- mtdcr (ebccfga, pb1cr);
+ mtdcr (EBC0_CFGADDR, PB1CR);
+ pbcr = mfdcr (EBC0_CFGDATA);
+ mtdcr (EBC0_CFGADDR, PB1CR);
base_b0 = base_b1 - size_b0;
pbcr = (pbcr & 0x0001ffff) | base_b0 |
(((size_b0 / 1024 / 1024) - 1) << 17);
- mtdcr (ebccfgd, pbcr);
- /* printf("pb0cr = %x\n", pbcr); */
+ mtdcr (EBC0_CFGDATA, pbcr);
+ /* printf("PB0CR = %x\n", pbcr); */
}
size_b0 =
diff --git a/board/w7o/init.S b/board/w7o/init.S
index 902c631..090b07a 100644
--- a/board/w7o/init.S
+++ b/board/w7o/init.S
@@ -87,48 +87,48 @@
/********************************************************************
* Setup External Bus Controller (EBC).
*******************************************************************/
- addi r3, 0, epcr
- mtdcr ebccfga, r3
+ addi r3, 0, EBC0_CFG
+ mtdcr EBC0_CFGADDR, r3
addis r4, 0, 0xb040 /* Device base timeout = 1024 cycles */
ori r4, r4, 0x0 /* Drive CS with external master */
- mtdcr ebccfgd, r4
+ mtdcr EBC0_CFGDATA, r4
/********************************************************************
* Change PCIINT signal to PerWE
*******************************************************************/
- mfdcr r4, cntrl1
+ mfdcr r4, CPC0_CR1
ori r4, r4, 0x4000
- mtdcr cntrl1, r4
+ mtdcr CPC0_CR1, r4
/********************************************************************
* Memory Bank 0 (Flash Bank 0) initialization
*******************************************************************/
- addi r3, 0, pb0ap
- mtdcr ebccfga, r3
+ addi r3, 0, PB1AP
+ mtdcr EBC0_CFGADDR, r3
addis r4, 0, CONFIG_SYS_W7O_EBC_PB0AP@h
ori r4, r4, CONFIG_SYS_W7O_EBC_PB0AP@l
- mtdcr ebccfgd, r4
+ mtdcr EBC0_CFGDATA, r4
- addi r3, 0, pb0cr
- mtdcr ebccfga, r3
+ addi r3, 0, PB0CR
+ mtdcr EBC0_CFGADDR, r3
addis r4, 0, CONFIG_SYS_W7O_EBC_PB0CR@h
ori r4, r4, CONFIG_SYS_W7O_EBC_PB0CR@l
- mtdcr ebccfgd, r4
+ mtdcr EBC0_CFGDATA, r4
/********************************************************************
* Memory Bank 7 LEDs - NEEDED BECAUSE OF HW WATCHDOG AND LEDs.
*******************************************************************/
- addi r3, 0, pb7ap
- mtdcr ebccfga, r3
+ addi r3, 0, PB7AP
+ mtdcr EBC0_CFGADDR, r3
addis r4, 0, CONFIG_SYS_W7O_EBC_PB7AP@h
ori r4, r4, CONFIG_SYS_W7O_EBC_PB7AP@l
- mtdcr ebccfgd, r4
+ mtdcr EBC0_CFGDATA, r4
- addi r3, 0, pb7cr
- mtdcr ebccfga, r3
+ addi r3, 0, PB7CR
+ mtdcr EBC0_CFGADDR, r3
addis r4, 0, CONFIG_SYS_W7O_EBC_PB7CR@h
ori r4, r4, CONFIG_SYS_W7O_EBC_PB7CR@l
- mtdcr ebccfgd, r4
+ mtdcr EBC0_CFGDATA, r4
/* We are all done */
mtlr r0 /* Restore link register */
@@ -183,35 +183,35 @@
* values to be changed.
*/
addi r3, 0, mem_mcopt1
- mtdcr memcfga, r3
+ mtdcr SDRAM0_CFGADDR, r3
addis r4, 0, 0x0
ori r4, r4, 0x0
- mtdcr memcfgd, r4
+ mtdcr SDRAM0_CFGDATA, r4
/*
* Set MB0CF for ext bank 0. (0-4MB) Address Mode 5 since 11x8x2
* All other banks are disabled.
*/
addi r3, 0, mem_mb0cf
- mtdcr memcfga, r3
+ mtdcr SDRAM0_CFGADDR, r3
addis r4, 0, 0x0000 /* BA=0x0, SZ=4MB */
ori r4, r4, 0x8001 /* Mode is 5, 11x8x2or4, BE=Enabled */
- mtdcr memcfgd, r4
+ mtdcr SDRAM0_CFGDATA, r4
/* Clear MB1CR,MB2CR,MB3CR to turn other banks off */
addi r4, 0, 0 /* Zero the data reg */
addi r3, r3, 4 /* Point to MB1CF reg */
- mtdcr memcfga, r3 /* Set the address */
- mtdcr memcfgd, r4 /* Zero the reg */
+ mtdcr SDRAM0_CFGADDR, r3 /* Set the address */
+ mtdcr SDRAM0_CFGDATA, r4 /* Zero the reg */
addi r3, r3, 4 /* Point to MB2CF reg */
- mtdcr memcfga, r3 /* Set the address */
- mtdcr memcfgd, r4 /* Zero the reg */
+ mtdcr SDRAM0_CFGADDR, r3 /* Set the address */
+ mtdcr SDRAM0_CFGDATA, r4 /* Zero the reg */
addi r3, r3, 4 /* Point to MB3CF reg */
- mtdcr memcfga, r3 /* Set the address */
- mtdcr memcfgd, r4 /* Zero the reg */
+ mtdcr SDRAM0_CFGADDR, r3 /* Set the address */
+ mtdcr SDRAM0_CFGDATA, r4 /* Zero the reg */
/********************************************************************
* Set the SDRAM Timing reg, SDTR1 and the refresh timer reg, RTR.
@@ -223,18 +223,18 @@
* Set up SDTR1
*/
addi r3, 0, mem_sdtr1
- mtdcr memcfga, r3
+ mtdcr SDRAM0_CFGADDR, r3
addis r4, 0, 0x0086 /* SDTR1 value for 100Mhz */
ori r4, r4, 0x400D
- mtdcr memcfgd, r4
+ mtdcr SDRAM0_CFGDATA, r4
/*
* Set RTR
*/
addi r3, 0, mem_rtr
- mtdcr memcfga, r3
+ mtdcr SDRAM0_CFGADDR, r3
addis r4, 0, 0x05F0 /* RTR refresh val = 15.625ms@100Mhz */
- mtdcr memcfgd, r4
+ mtdcr SDRAM0_CFGDATA, r4
/********************************************************************
* Delay to ensure 200usec have elapsed since reset. Assume worst
@@ -251,10 +251,10 @@
* Set memory controller options reg, MCOPT1.
*******************************************************************/
addi r3, 0, mem_mcopt1
- mtdcr memcfga, r3
+ mtdcr SDRAM0_CFGADDR, r3
addis r4, 0, 0x80E0 /* DC_EN=1,SRE=0,PME=0,MEMCHK=0 */
ori r4, r4, 0x0000 /* REGEN=0,DRW=00,BRPF=01,ECCDD=1 */
- mtdcr memcfgd, r4 /* EMDULR=1 */
+ mtdcr SDRAM0_CFGDATA, r4 /* EMDULR=1 */
..sdri_done:
/* restore and return */
diff --git a/board/w7o/w7o.c b/board/w7o/w7o.c
index 22cdfcd..6479bee 100644
--- a/board/w7o/w7o.c
+++ b/board/w7o/w7o.c
@@ -170,17 +170,17 @@
int size = 0;
/* Get bank Size registers */
- mtdcr (memcfga, mem_mb0cf); /* get bank 0 config reg */
- regs[0] = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_mb0cf); /* get bank 0 config reg */
+ regs[0] = mfdcr (SDRAM0_CFGDATA);
- mtdcr (memcfga, mem_mb1cf); /* get bank 1 config reg */
- regs[1] = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_mb1cf); /* get bank 1 config reg */
+ regs[1] = mfdcr (SDRAM0_CFGDATA);
- mtdcr (memcfga, mem_mb2cf); /* get bank 2 config reg */
- regs[2] = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_mb2cf); /* get bank 2 config reg */
+ regs[2] = mfdcr (SDRAM0_CFGDATA);
- mtdcr (memcfga, mem_mb3cf); /* get bank 3 config reg */
- regs[3] = mfdcr (memcfgd);
+ mtdcr (SDRAM0_CFGADDR, mem_mb3cf); /* get bank 3 config reg */
+ regs[3] = mfdcr (SDRAM0_CFGDATA);
/* compute the size, add each bank if enabled */
for (i = 0; i < 4; i++) {
diff --git a/board/xes/xpedite1000/xpedite1000.c b/board/xes/xpedite1000/xpedite1000.c
index 4529b7e..58041fc 100644
--- a/board/xes/xpedite1000/xpedite1000.c
+++ b/board/xes/xpedite1000/xpedite1000.c
@@ -42,8 +42,8 @@
* 23 = #LED_STATUS1
* 24 = #LED_STATUS2
*/
- mfsdr(sdr_pfc0, sdrreg);
- mtsdr(sdr_pfc0, (sdrreg & ~SDR0_PFC0_TRE_ENABLE) | 0x00003e00);
+ mfsdr(SDR0_PFC0, sdrreg);
+ mtsdr(SDR0_PFC0, (sdrreg & ~SDR0_PFC0_TRE_ENABLE) | 0x00003e00);
out32(CONFIG_SYS_GPIO_BASE + 0x018, (USR_LED0 | USR_LED1 | USR_LED2 | USR_LED3));
LED0_OFF();
LED1_OFF();
@@ -51,14 +51,14 @@
LED3_OFF();
/* Setup the external bus controller/chip selects */
- mtebc(pb0ap, 0x04055200); /* 16MB Strata FLASH */
- mtebc(pb0cr, 0xff098000); /* BAS=0xff0 16MB R/W 8-bit */
- mtebc(pb1ap, 0x04055200); /* 512KB Socketed AMD FLASH */
- mtebc(pb1cr, 0xfe018000); /* BAS=0xfe0 1MB R/W 8-bit */
- mtebc(pb6ap, 0x05006400); /* 32-64MB AMD MirrorBit FLASH */
- mtebc(pb6cr, 0xf00da000); /* BAS=0xf00 64MB R/W i6-bit */
- mtebc(pb7ap, 0x05006400); /* 32-64MB AMD MirrorBit FLASH */
- mtebc(pb7cr, 0xf40da000); /* BAS=0xf40 64MB R/W 16-bit */
+ mtebc(PB0AP, 0x04055200); /* 16MB Strata FLASH */
+ mtebc(PB0CR, 0xff098000); /* BAS=0xff0 16MB R/W 8-bit */
+ mtebc(PB1AP, 0x04055200); /* 512KB Socketed AMD FLASH */
+ mtebc(PB1CR, 0xfe018000); /* BAS=0xfe0 1MB R/W 8-bit */
+ mtebc(PB6AP, 0x05006400); /* 32-64MB AMD MirrorBit FLASH */
+ mtebc(PB6CR, 0xf00da000); /* BAS=0xf00 64MB R/W i6-bit */
+ mtebc(PB7AP, 0x05006400); /* 32-64MB AMD MirrorBit FLASH */
+ mtebc(PB7CR, 0xf40da000); /* BAS=0xf40 64MB R/W 16-bit */
/*
* Setup the interrupt controller polarities, triggers, etc.
@@ -151,15 +151,15 @@
unsigned long strap;
/* See if we're supposed to setup the pci */
- mfsdr(sdr_sdstp1, strap);
+ mfsdr(SDR0_SDSTP1, strap);
if ((strap & 0x00010000) == 0)
return 0;
#if defined(CONFIG_SYS_PCI_FORCE_PCI_CONV)
/* Setup System Device Register PCIX0_XCR */
- mfsdr(sdr_xcr, strap);
+ mfsdr(SDR0_XCR, strap);
strap &= 0x0f000000;
- mtsdr(sdr_xcr, strap);
+ mtsdr(SDR0_XCR, strap);
#endif
return 1;
diff --git a/board/zeus/zeus.c b/board/zeus/zeus.c
index 9bc390f..fc9dfa0 100644
--- a/board/zeus/zeus.c
+++ b/board/zeus/zeus.c
@@ -61,7 +61,7 @@
/*
* Configure CPC0_PCI to enable PerWE as output
*/
- mtdcr(cpc0_pci, CPC0_PCI_SPE);
+ mtdcr(CPC0_PCI, CPC0_PCI_SPE);
return 0;
}
@@ -107,7 +107,7 @@
/* Re-do sizing to get full correct info */
/* adjust flash start and offset */
- mfebc(pb0cr, pbcr);
+ mfebc(PB0CR, pbcr);
switch (gd->bd->bi_flashsize) {
case 1 << 20:
size_val = 0;
@@ -135,7 +135,7 @@
break;
}
pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
- mtebc(pb0cr, pbcr);
+ mtebc(PB0CR, pbcr);
/*
* Re-check to get correct base address