ehci-omap: driver for EHCI host on OMAP3
Taken from Beagle code. Tested on mcx board (AM3517-based).
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Tested-by: Stefano Babic <sbabic@denx.de>
diff --git a/drivers/usb/host/ehci-omap.c b/drivers/usb/host/ehci-omap.c
new file mode 100644
index 0000000..93d3bb7
--- /dev/null
+++ b/drivers/usb/host/ehci-omap.c
@@ -0,0 +1,156 @@
+/*
+ * (C) Copyright 2011 Ilya Yanok, Emcraft Systems
+ * (C) Copyright 2004-2008
+ * Texas Instruments, <www.ti.com>
+ *
+ * Derived from Beagle Board code by
+ * Sunil Kumar <sunilsaini05@gmail.com>
+ * Shashi Ranjan <shashiranjanmca05@gmail.com>
+ *
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc.
+ */
+#include <common.h>
+#include <usb.h>
+#include <asm/io.h>
+#include <asm/gpio.h>
+#include <asm/arch/clocks.h>
+#include <asm/arch/clocks_omap3.h>
+#include <asm/arch/ehci_omap3.h>
+#include <asm/arch/sys_proto.h>
+#include "ehci-core.h"
+
+inline int __board_usb_init(void)
+{
+ return 0;
+}
+int board_usb_init(void) __attribute__((weak, alias("__board_usb_init")));
+
+#if defined(CONFIG_OMAP_EHCI_PHY1_RESET_GPIO) || \
+ defined(CONFIG_OMAP_EHCI_PHY2_RESET_GPIO)
+/* controls PHY(s) reset signal(s) */
+static inline void omap_ehci_phy_reset(int on, int delay)
+{
+ /*
+ * Refer ISSUE1:
+ * Hold the PHY in RESET for enough time till
+ * PHY is settled and ready
+ */
+ if (delay && !on)
+ udelay(delay);
+#ifdef CONFIG_OMAP_EHCI_PHY1_RESET_GPIO
+ gpio_request(CONFIG_OMAP_EHCI_PHY1_RESET_GPIO, "USB PHY1 reset");
+ gpio_direction_output(CONFIG_OMAP_EHCI_PHY1_RESET_GPIO, !on);
+#endif
+#ifdef CONFIG_OMAP_EHCI_PHY2_RESET_GPIO
+ gpio_request(CONFIG_OMAP_EHCI_PHY2_RESET_GPIO, "USB PHY2 reset");
+ gpio_direction_output(CONFIG_OMAP_EHCI_PHY2_RESET_GPIO, !on);
+#endif
+
+ /* Hold the PHY in RESET for enough time till DIR is high */
+ /* Refer: ISSUE1 */
+ if (delay && on)
+ udelay(delay);
+}
+#else
+#define omap_ehci_phy_reset(on, delay) do {} while (0)
+#endif
+
+/* Reset is needed otherwise the kernel-driver will throw an error. */
+int ehci_hcd_stop(void)
+{
+ debug("Resetting OMAP3 EHCI\n");
+ omap_ehci_phy_reset(1, 0);
+ writel(OMAP_UHH_SYSCONFIG_SOFTRESET,
+ OMAP3_UHH_BASE + OMAP_UHH_SYSCONFIG);
+ /* disable USB clocks */
+ struct prcm *prcm_base = (struct prcm *)PRCM_BASE;
+ sr32(&prcm_base->iclken_usbhost, 0, 1, 0);
+ sr32(&prcm_base->fclken_usbhost, 0, 2, 0);
+ sr32(&prcm_base->iclken3_core, 2, 1, 0);
+ sr32(&prcm_base->fclken3_core, 2, 1, 0);
+ return 0;
+}
+
+/*
+ * Initialize the OMAP3 EHCI controller and PHY.
+ * Based on "drivers/usb/host/ehci-omap.c" from Linux 2.6.37.
+ * See there for additional Copyrights.
+ */
+int ehci_hcd_init(void)
+{
+ int ret;
+
+ debug("Initializing OMAP3 EHCI\n");
+
+ ret = board_usb_init();
+ if (ret < 0)
+ return ret;
+
+ /* Put the PHY in RESET */
+ omap_ehci_phy_reset(1, 10);
+
+ struct prcm *prcm_base = (struct prcm *)PRCM_BASE;
+ /* Enable USBHOST_L3_ICLK (USBHOST_MICLK) */
+ sr32(&prcm_base->iclken_usbhost, 0, 1, 1);
+ /*
+ * Enable USBHOST_48M_FCLK (USBHOST_FCLK1)
+ * and USBHOST_120M_FCLK (USBHOST_FCLK2)
+ */
+ sr32(&prcm_base->fclken_usbhost, 0, 2, 3);
+ /* Enable USBTTL_ICLK */
+ sr32(&prcm_base->iclken3_core, 2, 1, 1);
+ /* Enable USBTTL_FCLK */
+ sr32(&prcm_base->fclken3_core, 2, 1, 1);
+ debug("USB clocks enabled\n");
+
+ /* perform TLL soft reset, and wait until reset is complete */
+ writel(OMAP_USBTLL_SYSCONFIG_SOFTRESET,
+ OMAP3_USBTLL_BASE + OMAP_USBTLL_SYSCONFIG);
+ /* Wait for TLL reset to complete */
+ while (!(readl(OMAP3_USBTLL_BASE + OMAP_USBTLL_SYSSTATUS)
+ & OMAP_USBTLL_SYSSTATUS_RESETDONE))
+ ;
+ debug("TLL reset done\n");
+
+ writel(OMAP_USBTLL_SYSCONFIG_ENAWAKEUP |
+ OMAP_USBTLL_SYSCONFIG_SIDLEMODE |
+ OMAP_USBTLL_SYSCONFIG_CACTIVITY,
+ OMAP3_USBTLL_BASE + OMAP_USBTLL_SYSCONFIG);
+
+ /* Put UHH in NoIdle/NoStandby mode */
+ writel(OMAP_UHH_SYSCONFIG_ENAWAKEUP
+ | OMAP_UHH_SYSCONFIG_SIDLEMODE
+ | OMAP_UHH_SYSCONFIG_CACTIVITY
+ | OMAP_UHH_SYSCONFIG_MIDLEMODE,
+ OMAP3_UHH_BASE + OMAP_UHH_SYSCONFIG);
+
+ /* setup burst configurations */
+ writel(OMAP_UHH_HOSTCONFIG_INCR4_BURST_EN
+ | OMAP_UHH_HOSTCONFIG_INCR8_BURST_EN
+ | OMAP_UHH_HOSTCONFIG_INCR16_BURST_EN,
+ OMAP3_UHH_BASE + OMAP_UHH_HOSTCONFIG);
+
+ omap_ehci_phy_reset(0, 10);
+
+ hccr = (struct ehci_hccr *)(OMAP3_EHCI_BASE);
+ hcor = (struct ehci_hcor *)(OMAP3_EHCI_BASE + 0x10);
+
+ debug("OMAP3 EHCI init done\n");
+ return 0;
+}