tegra2: Simplify tegra_start() boot path
The Tegra2 boot path is more complicated than it needs to be. Since we want
to move to building most of U-Boot with ARMv7 and only a small part with
ARMv4T (for AVP) it should be as simple as possible.
This makes tegra2_start() into a simple function which either does AVP
init or A9 init depending on which core is running it. Both cores now
following the same init path, beginning at _start, and the special Tegra2
boot path code is no longer required.
Only two files need to be built for ARMv4T, and this is handled in the
Tegra2 CPU Makefile.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
diff --git a/arch/arm/cpu/armv7/tegra2/Makefile b/arch/arm/cpu/armv7/tegra2/Makefile
index f0dc2ff..955c3b6 100644
--- a/arch/arm/cpu/armv7/tegra2/Makefile
+++ b/arch/arm/cpu/armv7/tegra2/Makefile
@@ -23,6 +23,11 @@
# MA 02111-1307 USA
#
+# The AVP is ARMv4T architecture so we must use special compiler
+# flags for any startup files it might use.
+CFLAGS_arch/arm/cpu/armv7/tegra2/ap20.o += -march=armv4t
+CFLAGS_arch/arm/cpu/armv7/tegra2/clock.o += -march=armv4t
+
include $(TOPDIR)/config.mk
LIB = $(obj)lib$(SOC).o
diff --git a/arch/arm/cpu/armv7/tegra2/ap20.c b/arch/arm/cpu/armv7/tegra2/ap20.c
index 5cb4b1b..4c44bb3 100644
--- a/arch/arm/cpu/armv7/tegra2/ap20.c
+++ b/arch/arm/cpu/armv7/tegra2/ap20.c
@@ -31,7 +31,12 @@
#include <asm/arch/scu.h>
#include <common.h>
-u32 s_first_boot = 1;
+/* Returns 1 if the current CPU executing is a Cortex-A9, else 0 */
+static int ap20_cpu_is_cortexa9(void)
+{
+ u32 id = readb(NV_PA_PG_UP_BASE + PG_UP_TAG_0);
+ return id == (PG_UP_TAG_0_PID_CPU & 0xff);
+}
void init_pllx(void)
{
@@ -283,38 +288,37 @@
writel(CONFIG_SYS_BOARD_ODMDATA, &pmc->pmc_scratch20);
}
-void cpu_start(void)
+void tegra2_start(void)
{
struct pmux_tri_ctlr *pmt = (struct pmux_tri_ctlr *)NV_PA_APB_MISC_BASE;
- /* enable JTAG */
- writel(0xC0, &pmt->pmt_cfg_ctl);
+ /* If we are the AVP, start up the first Cortex-A9 */
+ if (!ap20_cpu_is_cortexa9()) {
+ /* enable JTAG */
+ writel(0xC0, &pmt->pmt_cfg_ctl);
- if (s_first_boot) {
/*
- * Need to set this before cold-booting,
- * otherwise we'll end up in an infinite loop.
- */
- s_first_boot = 0;
- cold_boot();
- }
-}
+ * If we are ARM7 - give it a different stack. We are about to
+ * start up the A9 which will want to use this one.
+ */
+ asm volatile("ldr sp, =%c0\n"
+ : : "i"(AVP_EARLY_BOOT_STACK_LIMIT));
-void tegra2_start()
-{
- if (s_first_boot) {
- /* Init Debug UART Port (115200 8n1) */
- uart_init();
-
- /* Init PMC scratch memory */
- init_pmc_scratch();
+ start_cpu((u32)_start);
+ halt_avp();
+ /* not reached */
}
-#ifdef CONFIG_ENABLE_CORTEXA9
- /* take the mpcore out of reset */
- cpu_start();
+ /* Init PMC scratch memory */
+ init_pmc_scratch();
- /* configure cache */
- cache_configure();
-#endif
+ enable_scu();
+
+ /* enable SMP mode and FW for CPU0, by writing to Auxiliary Ctl reg */
+ asm volatile(
+ "mrc p15, 0, r0, c1, c0, 1\n"
+ "orr r0, r0, #0x41\n"
+ "mcr p15, 0, r0, c1, c0, 1\n");
+
+ /* FIXME: should have ap20's L2 disabled too? */
}
diff --git a/arch/arm/cpu/armv7/tegra2/ap20.h b/arch/arm/cpu/armv7/tegra2/ap20.h
index 49fe340..1bb48d6 100644
--- a/arch/arm/cpu/armv7/tegra2/ap20.h
+++ b/arch/arm/cpu/armv7/tegra2/ap20.h
@@ -102,3 +102,6 @@
void udelay(unsigned long);
void cold_boot(void);
void cache_configure(void);
+
+/* This is the main entry into U-Boot, used by the Cortex-A9 */
+extern void _start(void);