arm: mx6: cm_fx6: add sata support
Add support for SATA.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
diff --git a/board/compulab/cm_fx6/cm_fx6.c b/board/compulab/cm_fx6/cm_fx6.c
index 1664fe8..fdb8ebf 100644
--- a/board/compulab/cm_fx6/cm_fx6.c
+++ b/board/compulab/cm_fx6/cm_fx6.c
@@ -13,10 +13,12 @@
#include <miiphy.h>
#include <netdev.h>
#include <fdt_support.h>
+#include <sata.h>
#include <asm/arch/crm_regs.h>
#include <asm/arch/sys_proto.h>
#include <asm/arch/iomux.h>
#include <asm/imx-common/mxc_i2c.h>
+#include <asm/imx-common/sata.h>
#include <asm/io.h>
#include <asm/gpio.h>
#include "common.h"
@@ -24,6 +26,91 @@
DECLARE_GLOBAL_DATA_PTR;
+#ifdef CONFIG_DWC_AHSATA
+static int cm_fx6_issd_gpios[] = {
+ /* The order of the GPIOs in the array is important! */
+ CM_FX6_SATA_PHY_SLP,
+ CM_FX6_SATA_NRSTDLY,
+ CM_FX6_SATA_PWREN,
+ CM_FX6_SATA_NSTANDBY1,
+ CM_FX6_SATA_NSTANDBY2,
+ CM_FX6_SATA_LDO_EN,
+};
+
+static void cm_fx6_sata_power(int on)
+{
+ int i;
+
+ if (!on) { /* tell the iSSD that the power will be removed */
+ gpio_direction_output(CM_FX6_SATA_PWLOSS_INT, 1);
+ mdelay(10);
+ }
+
+ for (i = 0; i < ARRAY_SIZE(cm_fx6_issd_gpios); i++) {
+ gpio_direction_output(cm_fx6_issd_gpios[i], on);
+ udelay(100);
+ }
+
+ if (!on) /* for compatibility lower the power loss interrupt */
+ gpio_direction_output(CM_FX6_SATA_PWLOSS_INT, 0);
+}
+
+static iomux_v3_cfg_t const sata_pads[] = {
+ /* SATA PWR */
+ IOMUX_PADS(PAD_ENET_TX_EN__GPIO1_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_A22__GPIO2_IO16 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_D20__GPIO3_IO20 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_A25__GPIO5_IO02 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ /* SATA CTRL */
+ IOMUX_PADS(PAD_ENET_TXD0__GPIO1_IO30 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_D23__GPIO3_IO23 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_D29__GPIO3_IO29 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_A23__GPIO6_IO06 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+ IOMUX_PADS(PAD_EIM_BCLK__GPIO6_IO31 | MUX_PAD_CTRL(NO_PAD_CTRL)),
+};
+
+static void cm_fx6_setup_issd(void)
+{
+ SETUP_IOMUX_PADS(sata_pads);
+ /* Make sure this gpio has logical 0 value */
+ gpio_direction_output(CM_FX6_SATA_PWLOSS_INT, 0);
+ udelay(100);
+
+ cm_fx6_sata_power(0);
+ mdelay(250);
+ cm_fx6_sata_power(1);
+}
+
+#define CM_FX6_SATA_INIT_RETRIES 10
+int sata_initialize(void)
+{
+ int err, i;
+
+ cm_fx6_setup_issd();
+ for (i = 0; i < CM_FX6_SATA_INIT_RETRIES; i++) {
+ err = setup_sata();
+ if (err) {
+ printf("SATA setup failed: %d\n", err);
+ return err;
+ }
+
+ udelay(100);
+
+ err = __sata_initialize();
+ if (!err)
+ break;
+
+ /* There is no device on the SATA port */
+ if (sata_port_status(0, 0) == 0)
+ break;
+
+ /* There's a device, but link not established. Retry */
+ }
+
+ return err;
+}
+#endif
+
#ifdef CONFIG_SYS_I2C_MXC
#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
diff --git a/board/compulab/cm_fx6/common.h b/board/compulab/cm_fx6/common.h
index f841c90..76097f8 100644
--- a/board/compulab/cm_fx6/common.h
+++ b/board/compulab/cm_fx6/common.h
@@ -19,6 +19,19 @@
#define CM_FX6_ENET_NRST IMX_GPIO_NR(2, 8)
#define CM_FX6_USB_HUB_RST IMX_GPIO_NR(7, 8)
#define SB_FX6_USB_OTG_PWR IMX_GPIO_NR(3, 22)
+#define CM_FX6_ENET_NRST IMX_GPIO_NR(2, 8)
+#define CM_FX6_USB_HUB_RST IMX_GPIO_NR(7, 8)
+#define SB_FX6_USB_OTG_PWR IMX_GPIO_NR(3, 22)
+#define CM_FX6_SATA_PWREN IMX_GPIO_NR(1, 28)
+#define CM_FX6_SATA_VDDC_CTRL IMX_GPIO_NR(1, 30)
+#define CM_FX6_SATA_LDO_EN IMX_GPIO_NR(2, 16)
+#define CM_FX6_SATA_NSTANDBY1 IMX_GPIO_NR(3, 20)
+#define CM_FX6_SATA_PHY_SLP IMX_GPIO_NR(3, 23)
+#define CM_FX6_SATA_STBY_REQ IMX_GPIO_NR(3, 29)
+#define CM_FX6_SATA_NSTANDBY2 IMX_GPIO_NR(5, 2)
+#define CM_FX6_SATA_NRSTDLY IMX_GPIO_NR(6, 6)
+#define CM_FX6_SATA_PWLOSS_INT IMX_GPIO_NR(6, 31)
+
void cm_fx6_set_usdhc_iomux(void);
void cm_fx6_set_ecspi_iomux(void);