* Patch by Rishi Bhattacharya, 08 May 2004:
Add support for TI OMAP5912 OSK Board
* Patch by Sam Song May, 07 May 2004:
Fix typo of UPM table for rmu board
diff --git a/board/omap730p2/omap730p2.c b/board/omap730p2/omap730p2.c
index 5e2fa3b..585b6ee 100644
--- a/board/omap730p2/omap730p2.c
+++ b/board/omap730p2/omap730p2.c
@@ -20,7 +20,7 @@
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
@@ -41,12 +41,12 @@
void set_muxconf_regs (void);
void peripheral_power_enable (void);
-#define FLASH_ON_CS0 1
-#define FLASH_ON_CS3 0
+#define FLASH_ON_CS0 1
+#define FLASH_ON_CS3 0
static inline void delay (unsigned long loops)
{
- __asm__ volatile ("1:\n"
+ __asm__ volatile ("1:\n"
"subs %0, %1, #1\n"
"bne 1b":"=r" (loops):"0" (loops));
}
@@ -63,7 +63,7 @@
/* Toggle backup LED indication */
void toggle_backup_led(void)
{
- static int backupLEDState = 0; /* Init variable so that the LED will be ON the first time */
+ static int backupLEDState = 0; /* Init variable so that the LED will be ON the first time */
volatile unsigned int *IOConfReg;
@@ -145,18 +145,18 @@
******************************/
void flash__init (void)
{
- unsigned int regval;
+ unsigned int regval;
- regval = *((volatile unsigned int *) EMIFS_CONFIG);
- /* Turn off write protection for flash devices. */
- regval = regval | 0x0001;
- *((volatile unsigned int *) EMIFS_CONFIG) = regval;
+ regval = *((volatile unsigned int *) EMIFS_CONFIG);
+ /* Turn off write protection for flash devices. */
+ regval = regval | 0x0001;
+ *((volatile unsigned int *) EMIFS_CONFIG) = regval;
}
/*************************************************************
Routine:ether__init
Description: take the Ethernet controller out of reset and wait
- for the EEPROM load to complete.
+ for the EEPROM load to complete.
*************************************************************/
void ether__init (void)
{
@@ -196,7 +196,7 @@
/******************************************************
Routine: set_muxconf_regs
Description: Setting up the configuration Mux registers
- specific to the hardware
+ specific to the hardware
*******************************************************/
void set_muxconf_regs (void)
{
@@ -209,12 +209,12 @@
/* Configure MUXed pin. Mode 6: GPIO_140 */
MuxConfReg = (volatile unsigned int *) (PERSEUS2_IO_CONF10);
- *MuxConfReg &= (0xFFFFFF1F); /* Clear D_MPU_LPG1 */
- *MuxConfReg |= 0x000000C0; /* Set D_MPU_LPG1 to 0x6 */
+ *MuxConfReg &= (0xFFFFFF1F); /* Clear D_MPU_LPG1 */
+ *MuxConfReg |= 0x000000C0; /* Set D_MPU_LPG1 to 0x6 */
/* Configure GPIO_140 as output */
MuxConfReg = (volatile unsigned int *) ((unsigned int) OMAP730_GPIO_BASE_5 + GPIO_DIRECTION_CONTROL);
- *MuxConfReg &= (0xFFFFEFFF); /* Clear direction (output) for GPIO 140 */
+ *MuxConfReg &= (0xFFFFEFFF); /* Clear direction (output) for GPIO 140 */
/*
* Configure GPIOs for battery charge & feedback
@@ -222,24 +222,24 @@
/* Configure MUXed pin. Mode 6: GPIO_35 */
MuxConfReg = (volatile unsigned int *) (PERSEUS2_IO_CONF3);
- *MuxConfReg &= 0xFFFFFFF1; /* Clear M_CLK_OUT */
- *MuxConfReg |= 0x0000000C; /* Set M_CLK_OUT = 0x6 (GPIOs) */
+ *MuxConfReg &= 0xFFFFFFF1; /* Clear M_CLK_OUT */
+ *MuxConfReg |= 0x0000000C; /* Set M_CLK_OUT = 0x6 (GPIOs) */
/* Configure MUXed pin. Mode 6: GPIO_72,73,74 */
MuxConfReg = (volatile unsigned int *) (PERSEUS2_IO_CONF5);
- *MuxConfReg &= 0xFFFF1FFF; /* Clear D_DDR */
- *MuxConfReg |= 0x0000C000; /* Set D_DDR = 0x6 (GPIOs) */
+ *MuxConfReg &= 0xFFFF1FFF; /* Clear D_DDR */
+ *MuxConfReg |= 0x0000C000; /* Set D_DDR = 0x6 (GPIOs) */
MuxConfReg = (volatile unsigned int *) ((unsigned int) OMAP730_GPIO_BASE_3 + GPIO_DIRECTION_CONTROL);
- *MuxConfReg |= 0x00000100; /* Configure GPIO_72 as input */
- *MuxConfReg &= 0xFFFFFDFF; /* Configure GPIO_73 as output */
+ *MuxConfReg |= 0x00000100; /* Configure GPIO_72 as input */
+ *MuxConfReg &= 0xFFFFFDFF; /* Configure GPIO_73 as output */
/*
* Allow battery charge
*/
MuxConfReg = (volatile unsigned int *) ((unsigned int) OMAP730_GPIO_BASE_3 + GPIO_DATA_OUTPUT);
- *MuxConfReg &= (0xFFFFFDFF); /* Clear GPIO_73 pin */
+ *MuxConfReg &= (0xFFFFFDFF); /* Clear GPIO_73 pin */
/*
* Configure MPU_EXT_NIRQ IO in IO_CONF9 register,