vexpress64: Refactor header file to make it easier to add new FVPs
Rename from vexpress_aemv8a.h -> vepxress_aemv8.h as new FVPs may not be
v8-A. No change in behavior.
This is towards future work to enable support for the FVP_BaseR.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
diff --git a/board/armltd/vexpress64/Kconfig b/board/armltd/vexpress64/Kconfig
index 1d13f54..4aab3f0 100644
--- a/board/armltd/vexpress64/Kconfig
+++ b/board/armltd/vexpress64/Kconfig
@@ -7,7 +7,7 @@
default "armltd"
config SYS_CONFIG_NAME
- default "vexpress_aemv8a"
+ default "vexpress_aemv8"
config JUNO_DTB_PART
string "NOR flash partition holding DTB"
diff --git a/doc/README.semihosting b/doc/README.semihosting
index c019999..f382d01 100644
--- a/doc/README.semihosting
+++ b/doc/README.semihosting
@@ -25,7 +25,7 @@
Rather than create a new armv8 board similar to armltd/vexpress64, add
semihosting calls to the existing one, enabled with CONFIG_SEMIHOSTING
and CONFIG_BASE_FVP both set. Also reuse the existing board config file
-vexpress_aemv8a.h but differentiate the two models by the presence or
+vexpress_aemv8.h but differentiate the two models by the presence or
absence of CONFIG_BASE_FVP. This change is tested and works on both the
Foundation and Base fastmodel simulators.
diff --git a/include/configs/vexpress_aemv8a.h b/include/configs/vexpress_aemv8.h
similarity index 87%
rename from include/configs/vexpress_aemv8a.h
rename to include/configs/vexpress_aemv8.h
index 44c746f..52fc15d 100644
--- a/include/configs/vexpress_aemv8a.h
+++ b/include/configs/vexpress_aemv8.h
@@ -4,36 +4,37 @@
* configurations.
*/
-#ifndef __VEXPRESS_AEMV8A_H
-#define __VEXPRESS_AEMV8A_H
+#ifndef __VEXPRESS_AEMV8_H
+#define __VEXPRESS_AEMV8_H
#define CONFIG_REMAKE_ELF
/* Link Definitions */
-#ifdef CONFIG_TARGET_VEXPRESS64_BASE_FVP
+#ifdef CONFIG_TARGET_VEXPRESS64_JUNO
+#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x7fff0)
+#else
/* ATF loads u-boot here for BASE_FVP model */
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x03f00000)
-#elif CONFIG_TARGET_VEXPRESS64_JUNO
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x7fff0)
#endif
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
/* CS register bases for the original memory map. */
-#define V2M_PA_CS0 0x00000000
-#define V2M_PA_CS1 0x14000000
-#define V2M_PA_CS2 0x18000000
-#define V2M_PA_CS3 0x1c000000
-#define V2M_PA_CS4 0x0c000000
-#define V2M_PA_CS5 0x10000000
+#define V2M_BASE 0x80000000
+#define V2M_PA_BASE 0x00000000
+
+#define V2M_PA_CS0 (V2M_PA_BASE + 0x00000000)
+#define V2M_PA_CS1 (V2M_PA_BASE + 0x14000000)
+#define V2M_PA_CS2 (V2M_PA_BASE + 0x18000000)
+#define V2M_PA_CS3 (V2M_PA_BASE + 0x1c000000)
+#define V2M_PA_CS4 (V2M_PA_BASE + 0x0c000000)
+#define V2M_PA_CS5 (V2M_PA_BASE + 0x10000000)
#define V2M_PERIPH_OFFSET(x) (x << 16)
#define V2M_SYSREGS (V2M_PA_CS3 + V2M_PERIPH_OFFSET(1))
#define V2M_SYSCTL (V2M_PA_CS3 + V2M_PERIPH_OFFSET(2))
#define V2M_SERIAL_BUS_PCI (V2M_PA_CS3 + V2M_PERIPH_OFFSET(3))
-#define V2M_BASE 0x80000000
-
/* Common peripherals relative to CS7. */
#define V2M_AACI (V2M_PA_CS3 + V2M_PERIPH_OFFSET(4))
#define V2M_MMCI (V2M_PA_CS3 + V2M_PERIPH_OFFSET(5))
@@ -72,23 +73,23 @@
/* Generic Interrupt Controller Definitions */
#ifdef CONFIG_GICV3
-#define GICD_BASE (0x2f000000)
-#define GICR_BASE (0x2f100000)
+#define GICD_BASE (V2M_PA_BASE + 0x2f000000)
+#define GICR_BASE (V2M_PA_BASE + 0x2f100000)
#else
-#ifdef CONFIG_TARGET_VEXPRESS64_BASE_FVP
-#define GICD_BASE (0x2f000000)
-#define GICC_BASE (0x2c000000)
-#elif CONFIG_TARGET_VEXPRESS64_JUNO
+#ifdef CONFIG_TARGET_VEXPRESS64_JUNO
#define GICD_BASE (0x2C010000)
#define GICC_BASE (0x2C02f000)
+#else
+#define GICD_BASE (V2M_PA_BASE + 0x2f000000)
+#define GICC_BASE (V2M_PA_BASE + 0x2c000000)
#endif
#endif /* !CONFIG_GICV3 */
#ifndef CONFIG_TARGET_VEXPRESS64_JUNO
/* The Vexpress64 simulators use SMSC91C111 */
#define CONFIG_SMC91111 1
-#define CONFIG_SMC91111_BASE (0x01A000000)
+#define CONFIG_SMC91111_BASE (V2M_PA_BASE + 0x01A000000)
#endif
/* PL011 Serial Configuration */
@@ -113,7 +114,7 @@
#ifdef CONFIG_TARGET_VEXPRESS64_JUNO
#define PHYS_SDRAM_2 (0x880000000)
#define PHYS_SDRAM_2_SIZE 0x180000000
-#elif CONFIG_TARGET_VEXPRESS64_BASE_FVP && CONFIG_NR_DRAM_BANKS == 2
+#elif CONFIG_NR_DRAM_BANKS == 2
#define PHYS_SDRAM_2 (0x880000000)
#define PHYS_SDRAM_2_SIZE 0x80000000
#endif
@@ -193,7 +194,7 @@
/* Store environment at top of flash in the same location as blank.img */
/* in the Juno firmware. */
#else
-#define CONFIG_SYS_FLASH_BASE 0x0C000000
+#define CONFIG_SYS_FLASH_BASE (V2M_PA_BASE + 0x0C000000)
/* 256 x 256KiB sectors */
#define CONFIG_SYS_MAX_FLASH_SECT 256
/* Store environment at top of flash */
@@ -210,4 +211,4 @@
#define CONFIG_SYS_FLASH_EMPTY_INFO /* flinfo indicates empty blocks */
#define FLASH_MAX_SECTOR_SIZE 0x00040000
-#endif /* __VEXPRESS_AEMV8A_H */
+#endif /* __VEXPRESS_AEMV8_H */