i.MX6: board: Add BTicino i.MX6DL Mamoj initial support

Add initial support for i.MX6DL BTicino Mamoj board.

Mamoh board added:
- SPL
- SPL_DM
- SPL_OF_CONTROL
- DM for U-Boot proper
- OF_CONTROL for U-Boot proper
- eMMC
- FEC
- Boot from eMMC
- Boot from USB SDP

Signed-off-by: Simone CIANNI <simone.cianni@bticino.it>
Signed-off-by: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 5300c27..b3a2405 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -404,6 +404,7 @@
 	imx6dl-icore.dtb \
 	imx6dl-icore-mipi.dtb \
 	imx6dl-icore-rqs.dtb \
+	imx6dl-mamoj.dtb \
 	imx6q-cm-fx6.dtb \
 	imx6q-icore.dtb \
 	imx6q-icore-mipi.dtb \
diff --git a/arch/arm/dts/imx6dl-mamoj-u-boot.dtsi b/arch/arm/dts/imx6dl-mamoj-u-boot.dtsi
new file mode 100644
index 0000000..d4c3c0b
--- /dev/null
+++ b/arch/arm/dts/imx6dl-mamoj-u-boot.dtsi
@@ -0,0 +1,15 @@
+/*
+ * Copyright (C) 2018 Jagan Teki <jagan@amarulasolutions.com>
+ *
+ * SPDX-License-Identifier:     GPL-2.0+
+ */
+
+#include "imx6qdl-u-boot.dtsi"
+
+&usdhc3 {
+	u-boot,dm-spl;
+};
+
+&pinctrl_usdhc3 {
+	u-boot,dm-spl;
+};
diff --git a/arch/arm/dts/imx6dl-mamoj.dts b/arch/arm/dts/imx6dl-mamoj.dts
new file mode 100644
index 0000000..068d518
--- /dev/null
+++ b/arch/arm/dts/imx6dl-mamoj.dts
@@ -0,0 +1,84 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (C) 2018 BTicino
+ * Copyright (C) 2018 Amarula Solutions B.V.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include "imx6dl.dtsi"
+
+/ {
+	model = "BTicino i.MX6DL Mamoj board";
+	compatible = "bticino,imx6dl-mamoj", "fsl,imx6dl";
+};
+
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet>;
+	phy-mode = "mii";
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	status = "okay";
+};
+
+&usdhc3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	bus-width = <8>;
+	non-removable;
+	keep-power-in-suspend;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_enet: enetgrp {
+		fsl,pins = <
+			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
+			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b1
+			MX6QDL_PAD_ENET_TXD0__ENET_TX_DATA0	0x1b0b0
+			MX6QDL_PAD_ENET_TXD1__ENET_TX_DATA1	0x1b0b0
+			MX6QDL_PAD_KEY_ROW2__ENET_TX_DATA2	0x1b0b0
+			MX6QDL_PAD_KEY_ROW0__ENET_TX_DATA3	0x1b0b0
+			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN	0x1b0b0
+			MX6QDL_PAD_GPIO_19__ENET_TX_ER		0x1b0b0
+			MX6QDL_PAD_GPIO_18__ENET_RX_CLK		0x1b0b1
+			MX6QDL_PAD_ENET_RXD0__ENET_RX_DATA0	0x1b0b0
+			MX6QDL_PAD_ENET_RXD1__ENET_RX_DATA1	0x1b0b0
+			MX6QDL_PAD_KEY_COL2__ENET_RX_DATA2	0x1b0b0
+			MX6QDL_PAD_KEY_COL0__ENET_RX_DATA3      0x1b0b0
+			MX6QDL_PAD_ENET_CRS_DV__ENET_RX_EN	0x1b0b0
+			MX6QDL_PAD_ENET_RX_ER__ENET_RX_ER	0x1b0b0
+			MX6QDL_PAD_KEY_COL3__ENET_CRS		0x1b0b0
+			MX6QDL_PAD_KEY_ROW1__ENET_COL		0x1b0b0
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1
+			MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b1
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6QDL_PAD_SD3_CMD__SD3_CMD	0x17059
+			MX6QDL_PAD_SD3_CLK__SD3_CLK	0x10059
+			MX6QDL_PAD_SD3_DAT0__SD3_DATA0	0x17059
+			MX6QDL_PAD_SD3_DAT1__SD3_DATA1	0x17059
+			MX6QDL_PAD_SD3_DAT2__SD3_DATA2	0x17059
+			MX6QDL_PAD_SD3_DAT3__SD3_DATA3	0x17059
+			MX6QDL_PAD_SD3_DAT4__SD3_DATA4	0x17059
+			MX6QDL_PAD_SD3_DAT5__SD3_DATA5	0x17059
+			MX6QDL_PAD_SD3_DAT6__SD3_DATA6	0x17059
+			MX6QDL_PAD_SD3_DAT7__SD3_DATA7	0x17059
+		>;
+	};
+};
diff --git a/arch/arm/mach-imx/mx6/Kconfig b/arch/arm/mach-imx/mx6/Kconfig
index f7157ab..8f469c4 100644
--- a/arch/arm/mach-imx/mx6/Kconfig
+++ b/arch/arm/mach-imx/mx6/Kconfig
@@ -220,6 +220,34 @@
 config TARGET_MX6QARM2
 	bool "mx6qarm2"
 
+config TARGET_MX6DL_MAMOJ
+	bool "Support BTicino Mamoj"
+	select MX6QDL
+	select OF_CONTROL
+	select PINCTRL
+	select DM
+	select DM_ETH
+	select DM_GPIO
+	select DM_MMC
+	select DM_THERMAL
+	select SPL
+	select SUPPORT_SPL
+	select SPL_DM if SPL
+	select SPL_OF_LIBFDT if SPL
+	select SPL_OF_CONTROL if SPL
+	select SPL_PINCTRL if SPL
+	select SPL_SEPARATE_BSS if SPL
+	select SPL_GPIO_SUPPORT if SPL
+	select SPL_LIBCOMMON_SUPPORT if SPL
+	select SPL_LIBDISK_SUPPORT if SPL
+	select SPL_LIBGENERIC_SUPPORT if SPL
+	select SPL_MMC_SUPPORT if SPL
+	select SPL_SERIAL_SUPPORT if SPL
+	select SPL_USB_HOST_SUPPORT if SPL
+	select SPL_USB_GADGET_SUPPORT if SPL
+	select SPL_USB_SDP_SUPPORT if SPL
+	select SPL_WATCHDOG_SUPPORT if SPL
+
 config TARGET_MX6Q_ENGICAM
 	bool "Support Engicam i.Core(RQS)"
 	select BOARD_LATE_INIT
@@ -463,6 +491,7 @@
 source "board/barco/platinum/Kconfig"
 source "board/barco/titanium/Kconfig"
 source "board/boundary/nitrogen6x/Kconfig"
+source "board/bticino/mamoj/Kconfig"
 source "board/ccv/xpress/Kconfig"
 source "board/compulab/cm_fx6/Kconfig"
 source "board/congatec/cgtqmx6eval/Kconfig"
diff --git a/board/bticino/mamoj/Kconfig b/board/bticino/mamoj/Kconfig
new file mode 100644
index 0000000..e5aec58
--- /dev/null
+++ b/board/bticino/mamoj/Kconfig
@@ -0,0 +1,12 @@
+if TARGET_MX6DL_MAMOJ
+
+config SYS_BOARD
+	default "mamoj"
+
+config SYS_VENDOR
+	default "bticino"
+
+config SYS_CONFIG_NAME
+	default "imx6dl-mamoj"
+
+endif
diff --git a/board/bticino/mamoj/MAINTAINERS b/board/bticino/mamoj/MAINTAINERS
new file mode 100644
index 0000000..c35b387
--- /dev/null
+++ b/board/bticino/mamoj/MAINTAINERS
@@ -0,0 +1,10 @@
+MX6DL_MAMOJ BOARD
+M:	Jagan Teki <jagan@amarulasolutions.com>
+M:	Raffaele RECALCATI <raffaele.recalcati@bticino.it>
+M:	Simone CIANNI <simone.cianni@bticino.it>
+S:	Maintained
+F:	board/bticino/mamoj
+F:	include/configs/imx6dl-mamoj.h
+F:	configs/imx6dl_mamoj_defconfig
+F:	arch/arm/dts/imx6dl-mamoj.dts
+F:	arch/arm/dts/imx6dl-mamoj-u-boot.dtsi
diff --git a/board/bticino/mamoj/Makefile b/board/bticino/mamoj/Makefile
new file mode 100644
index 0000000..f1ddda4
--- /dev/null
+++ b/board/bticino/mamoj/Makefile
@@ -0,0 +1,8 @@
+# Copyright (C) 2018 BTicino
+# Copyright (C) 2017 Amarula Solutions B.V.
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y := mamoj.o
+obj-$(CONFIG_SPL_BUILD) += spl.o
diff --git a/board/bticino/mamoj/README b/board/bticino/mamoj/README
new file mode 100644
index 0000000..eda9e45
--- /dev/null
+++ b/board/bticino/mamoj/README
@@ -0,0 +1,60 @@
+BTicino Mamoj board:
+===================
+
+Build:
+
+ $ make mrproper
+ $ make imx6dl_mamoj_defconfig
+ $ make
+
+   This will generate the SPL image called SPL and the u-boot-dtb.img.
+
+The following methods can be used for booting Mamoj boards:
+
+1. USB SDP boot
+
+1. USB SDP boot:
+---------------
+
+ - Build imx_usb_loader
+
+    $ git clone git://github.com/boundarydevices/imx_usb_loader.git
+    $ cd imx_usb_loader
+    $ make
+
+ - Build the BSP and copy SPL, u-boot-dtb.img in imx_usb_loader directory
+
+ - Put the board in "Serial Download Mode"
+
+ - Plug-in USB-to-Serial, Open minicom 1152008N1 and USB OTG cables to Host
+
+ - Turn-on board
+
+ - Identify VID/PID using lsusb
+
+    Bus 001 Device 010: ID 15a2:0061 Freescale Semiconductor, Inc. i.MX 6Solo/6DualLite SystemOnChip in RecoveryMode
+
+ - Update the conf files
+
+    imx_usb.conf
+      0x15a2:0x0061, mx6_usb_rom.conf, 0x0525:0xb4a4, mx6_usb_sdp_spl.conf
+
+    mx6_usb_rom.conf
+      mx6_usb
+      hid,1024,0x910000,0x10000000,512M,0x00900000,0x40000
+      SPL:jump header2
+
+    mx6_usb_sdp_spl.conf
+      mx6_spl_sdp
+      hid,uboot_header,1024,0x910000,0x10000000,512M,0x00900000,0x40000
+      u-boot-dtb.img:jump header2
+
+  - Launch the loader
+
+     $ ./imx_usb
+
+  We can see U-Boot boot from USB SDP on minicom
+
+--
+Jagan Teki <jagan@amarulasolutions.com>
+03/12/18
diff --git a/board/bticino/mamoj/mamoj.c b/board/bticino/mamoj/mamoj.c
new file mode 100644
index 0000000..478f673
--- /dev/null
+++ b/board/bticino/mamoj/mamoj.c
@@ -0,0 +1,27 @@
+/*
+ * Copyright (C) 2018 Simone CIANNI <simone.cianni@bticino.it>
+ * Copyright (C) 2018 Raffaele RECALCATI <raffaele.recalcati@bticino.it>
+ * Copyright (C) 2018 Jagan Teki <jagan@amarulasolutions.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/sys_proto.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_init(void)
+{
+	/* Address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+	return 0;
+}
+
+int dram_init(void)
+{
+	gd->ram_size = imx_ddr_size();
+
+	return 0;
+}
diff --git a/board/bticino/mamoj/spl.c b/board/bticino/mamoj/spl.c
new file mode 100644
index 0000000..4274cc8
--- /dev/null
+++ b/board/bticino/mamoj/spl.c
@@ -0,0 +1,161 @@
+/*
+ * Copyright (C) 2018 Simone CIANNI <simone.cianni@bticino.it>
+ * Copyright (C) 2018 Raffaele RECALCATI <raffaele.recalcati@bticino.it>
+ * Copyright (C) 2018 Jagan Teki <jagan@amarulasolutions.com>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <common.h>
+#include <spl.h>
+
+#include <asm/io.h>
+#include <linux/sizes.h>
+
+#include <asm/arch/clock.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-ddr.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/arch/sys_proto.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#define IMX6SDL_DRIVE_STRENGTH		0x28
+#define UART_PAD_CTRL	(PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
+			PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+static iomux_v3_cfg_t const uart3_pads[] = {
+	IOMUX_PADS(PAD_EIM_D24__UART3_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
+	IOMUX_PADS(PAD_EIM_D25__UART3_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL)),
+};
+
+struct mx6sdl_iomux_ddr_regs mx6sdl_ddr_ioregs = {
+	.dram_sdclk_0 = IMX6SDL_DRIVE_STRENGTH,
+	.dram_sdclk_1 = IMX6SDL_DRIVE_STRENGTH,
+	.dram_cas = IMX6SDL_DRIVE_STRENGTH,
+	.dram_ras = IMX6SDL_DRIVE_STRENGTH,
+	.dram_reset = IMX6SDL_DRIVE_STRENGTH,
+	.dram_sdcke0 = IMX6SDL_DRIVE_STRENGTH,
+	.dram_sdcke1 = IMX6SDL_DRIVE_STRENGTH,
+	.dram_sdba2 = 0x00000000,
+	.dram_sdodt0 = IMX6SDL_DRIVE_STRENGTH,
+	.dram_sdodt1 = IMX6SDL_DRIVE_STRENGTH,
+	.dram_sdqs0 = IMX6SDL_DRIVE_STRENGTH,
+	.dram_sdqs1 = IMX6SDL_DRIVE_STRENGTH,
+	.dram_sdqs2 = IMX6SDL_DRIVE_STRENGTH,
+	.dram_sdqs3 = IMX6SDL_DRIVE_STRENGTH,
+	.dram_sdqs4 = IMX6SDL_DRIVE_STRENGTH,
+	.dram_sdqs5 = IMX6SDL_DRIVE_STRENGTH,
+	.dram_sdqs6 = IMX6SDL_DRIVE_STRENGTH,
+	.dram_sdqs7 = IMX6SDL_DRIVE_STRENGTH,
+	.dram_dqm0 = IMX6SDL_DRIVE_STRENGTH,
+	.dram_dqm1 = IMX6SDL_DRIVE_STRENGTH,
+	.dram_dqm2 = IMX6SDL_DRIVE_STRENGTH,
+	.dram_dqm3 = IMX6SDL_DRIVE_STRENGTH,
+	.dram_dqm4 = IMX6SDL_DRIVE_STRENGTH,
+	.dram_dqm5 = IMX6SDL_DRIVE_STRENGTH,
+	.dram_dqm6 = IMX6SDL_DRIVE_STRENGTH,
+	.dram_dqm7 = IMX6SDL_DRIVE_STRENGTH,
+};
+
+struct mx6sdl_iomux_grp_regs mx6sdl_grp_ioregs = {
+	.grp_ddr_type = 0x000c0000,
+	.grp_ddrmode_ctl = 0x00020000,
+	.grp_ddrpke = 0x00000000,
+	.grp_addds = IMX6SDL_DRIVE_STRENGTH,
+	.grp_ctlds = IMX6SDL_DRIVE_STRENGTH,
+	.grp_ddrmode = 0x00020000,
+	.grp_b0ds = IMX6SDL_DRIVE_STRENGTH,
+	.grp_b1ds = IMX6SDL_DRIVE_STRENGTH,
+	.grp_b2ds = IMX6SDL_DRIVE_STRENGTH,
+	.grp_b3ds = IMX6SDL_DRIVE_STRENGTH,
+	.grp_b4ds = IMX6SDL_DRIVE_STRENGTH,
+	.grp_b5ds = IMX6SDL_DRIVE_STRENGTH,
+	.grp_b6ds = IMX6SDL_DRIVE_STRENGTH,
+	.grp_b7ds = IMX6SDL_DRIVE_STRENGTH,
+};
+
+static struct mx6_ddr3_cfg mt41k128m16jt_125 = {
+	.mem_speed = 1600,
+	.density = 4,
+	.width = 32,
+	.banks = 8,
+	.rowaddr = 14,
+	.coladdr = 10,
+	.pagesz = 2,
+	.trcd = 1375,
+	.trcmin = 4875,
+	.trasmin = 3500,
+	.SRT = 0,
+};
+
+static struct mx6_mmdc_calibration mx6dl_mmdc_calib = {
+	.p0_mpwldectrl0 = 0x0042004b,
+	.p0_mpwldectrl1 = 0x0038003c,
+	.p0_mpdgctrl0 = 0x42340230,
+	.p0_mpdgctrl1 = 0x0228022c,
+	.p0_mprddlctl = 0x42444646,
+	.p0_mpwrdlctl = 0x38382e2e,
+};
+
+static struct mx6_ddr_sysinfo mem_dl = {
+	.dsize		= 1,
+	.cs1_mirror	= 0,
+	/* config for full 4GB range so that get_mem_size() works */
+	.cs_density	= 32,
+	.ncs		= 1,
+	.bi_on		= 1,
+	.rtt_nom	= 1,
+	.rtt_wr		= 1,
+	.ralat		= 5,
+	.walat		= 0,
+	.mif3_mode	= 3,
+	.rst_to_cke	= 0x23,
+	.sde_to_rst	= 0x10,
+	.refsel		= 1,
+	.refr		= 7,
+};
+
+static void spl_dram_init(void)
+{
+	mx6sdl_dram_iocfg(64, &mx6sdl_ddr_ioregs, &mx6sdl_grp_ioregs);
+	mx6_dram_cfg(&mem_dl, &mx6dl_mmdc_calib, &mt41k128m16jt_125);
+
+	udelay(100);
+}
+
+static void ccgr_init(void)
+{
+	struct mxc_ccm_reg *ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+	writel(0x00003f3f, &ccm->CCGR0);
+	writel(0x0030fc00, &ccm->CCGR1);
+	writel(0x000fc000, &ccm->CCGR2);
+	writel(0x3f300000, &ccm->CCGR3);
+	writel(0xff00f300, &ccm->CCGR4);
+	writel(0x0f0000c3, &ccm->CCGR5);
+	writel(0x000003cc, &ccm->CCGR6);
+}
+
+void board_init_f(ulong dummy)
+{
+	ccgr_init();
+
+	/* setup AIPS and disable watchdog */
+	arch_cpu_init();
+
+	gpr_init();
+
+	/* iomux */
+	SETUP_IOMUX_PADS(uart3_pads);
+
+	/* setup GP timer */
+	timer_init();
+
+	/* UART clocks enabled and gd valid - init serial console */
+	preloader_console_init();
+
+	/* DDR initialization */
+	spl_dram_init();
+}
diff --git a/configs/imx6dl_mamoj_defconfig b/configs/imx6dl_mamoj_defconfig
new file mode 100644
index 0000000..e45ca9a
--- /dev/null
+++ b/configs/imx6dl_mamoj_defconfig
@@ -0,0 +1,39 @@
+CONFIG_ARM=y
+CONFIG_ARCH_MX6=y
+CONFIG_SYS_TEXT_BASE=0x17800000
+CONFIG_SYS_MALLOC_F_LEN=0x2000
+CONFIG_TARGET_MX6DL_MAMOJ=y
+# CONFIG_CMD_BMODE is not set
+CONFIG_DEFAULT_DEVICE_TREE="imx6dl-mamoj"
+CONFIG_SYS_EXTRA_OPTIONS="IMX_CONFIG=arch/arm/mach-imx/spl_sd.cfg"
+CONFIG_BOOTDELAY=3
+CONFIG_HUSH_PARSER=y
+CONFIG_SYS_PROMPT="=> "
+CONFIG_CRC32_VERIFY=y
+CONFIG_CMD_MEMTEST=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_MII=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_EXT4_WRITE=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_FS_GENERIC=y
+CONFIG_CMD_USB=y
+CONFIG_DISTRO_DEFAULTS=y
+CONFIG_ENV_IS_IN_MMC=y
+CONFIG_PHYLIB=y
+CONFIG_PHY_MICREL=y
+CONFIG_FEC_MXC=y
+CONFIG_FSL_ESDHC=y
+CONFIG_PINCTRL_IMX6=y
+CONFIG_MXC_UART=y
+CONFIG_USB=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_MANUFACTURER="FSL"
+CONFIG_USB_GADGET_VENDOR_NUM=0x0525
+CONFIG_USB_GADGET_PRODUCT_NUM=0xa4a5
+CONFIG_CI_UDC=y
+CONFIG_IMX_THERMAL=y
diff --git a/include/configs/imx6dl-mamoj.h b/include/configs/imx6dl-mamoj.h
new file mode 100644
index 0000000..929365a
--- /dev/null
+++ b/include/configs/imx6dl-mamoj.h
@@ -0,0 +1,88 @@
+/*
+ * Copyright (C) 2018 Simone CIANNI <simone.cianni@bticino.it>
+ * Copyright (C) 2018 Raffaele RECALCATI <raffaele.recalcati@bticino.it>
+ * Copyright (C) 2018 Jagan Teki <jagan@amarulasolutions.com>
+ *
+ * Configuration settings for the BTicion i.MX6DL Mamoj board.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __IMX6DL_MAMOJ_CONFIG_H
+#define __IMX6DL_MAMOJ_CONFIG_H
+
+#include <linux/sizes.h>
+#include "mx6_common.h"
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN		(16 * SZ_1M)
+
+/* Total Size of Environment Sector */
+#define CONFIG_ENV_SIZE			SZ_128K
+
+/* Allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+
+/* Environment */
+#ifndef CONFIG_ENV_IS_NOWHERE
+/* Environment in MMC */
+# if defined(CONFIG_ENV_IS_IN_MMC)
+#  define CONFIG_ENV_OFFSET		0x100000
+# endif
+#endif
+
+#ifndef CONFIG_SPL_BUILD
+#define CONFIG_EXTRA_ENV_SETTINGS	\
+	"scriptaddr=0x14000000\0"	\
+	"fdt_addr_r=0x13000000\0"	\
+	"kernel_addr_r=0x10008000\0"	\
+	"fdt_high=0xffffffff\0"		\
+	BOOTENV
+
+#define BOOT_TARGET_DEVICES(func) \
+	func(MMC, mmc, 2)
+
+#include <config_distro_bootcmd.h>
+#endif
+
+/* UART */
+#define CONFIG_MXC_UART_BASE		UART3_BASE
+
+/* MMC */
+#define CONFIG_SYS_MMC_ENV_DEV		2
+#define CONFIG_SUPPORT_EMMC_BOOT
+
+/* Ethernet */
+#define CONFIG_FEC_MXC_PHYADDR		1
+#define CONFIG_MII
+
+/* USB */
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_MXC_USB_PORTSC			(PORT_PTS_UTMI | PORT_PTS_PTW)
+#define CONFIG_MXC_USB_FLAGS			0
+#define CONFIG_USB_MAX_CONTROLLER_COUNT		2
+
+/* Miscellaneous configurable options */
+#define CONFIG_SYS_MEMTEST_START	0x80000000
+#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 0x8000000)
+
+#define CONFIG_SYS_LOAD_ADDR		CONFIG_LOADADDR
+#define CONFIG_SYS_HZ			1000
+
+/* Physical Memory Map */
+#define CONFIG_NR_DRAM_BANKS		1
+#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR
+
+#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
+#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
+#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE
+
+#define CONFIG_SYS_INIT_SP_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
+					GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_INIT_RAM_ADDR + \
+					CONFIG_SYS_INIT_SP_OFFSET)
+
+/* SPL */
+#include "imx6_spl.h"
+
+#endif /* __IMX6DL_MAMOJ_CONFIG_H */