fdt: update bcm283x device tree sources to Linux 5.1-rc6 state
Updating the bcm283x device tree sources adds the device trees for
- Raspberry Pi 3 Model A+
- Raspberry Pi 3 Model B+
- Raspberry Pi Compute Module IO board rev1
- Raspberry Pi Compute Module 3 IO board V3.0
- Raspberry Pi Zero
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
diff --git a/arch/arm/dts/bcm2835-rpi-zero.dts b/arch/arm/dts/bcm2835-rpi-zero.dts
new file mode 100644
index 0000000..3b35a8a
--- /dev/null
+++ b/arch/arm/dts/bcm2835-rpi-zero.dts
@@ -0,0 +1,105 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2016 Stefan Wahren <stefan.wahren@i2se.com>
+ */
+
+/dts-v1/;
+#include "bcm2835.dtsi"
+#include "bcm2835-rpi.dtsi"
+#include "bcm283x-rpi-usb-otg.dtsi"
+
+/ {
+ compatible = "raspberrypi,model-zero", "brcm,bcm2835";
+ model = "Raspberry Pi Zero";
+
+ leds {
+ act {
+ gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
+ };
+ };
+};
+
+&gpio {
+ /*
+ * This is based on the official GPU firmware DT blob.
+ *
+ * Legend:
+ * "NC" = not connected (no rail from the SoC)
+ * "FOO" = GPIO line named "FOO" on the schematic
+ * "FOO_N" = GPIO line named "FOO" on schematic, active low
+ */
+ gpio-line-names = "ID_SDA",
+ "ID_SCL",
+ "SDA1",
+ "SCL1",
+ "GPIO_GCLK",
+ "GPIO5",
+ "GPIO6",
+ "SPI_CE1_N",
+ "SPI_CE0_N",
+ "SPI_MISO",
+ "SPI_MOSI",
+ "SPI_SCLK",
+ "GPIO12",
+ "GPIO13",
+ /* Serial port */
+ "TXD0",
+ "RXD0",
+ "GPIO16",
+ "GPIO17",
+ "GPIO18",
+ "GPIO19",
+ "GPIO20",
+ "GPIO21",
+ "GPIO22",
+ "GPIO23",
+ "GPIO24",
+ "GPIO25",
+ "GPIO26",
+ "GPIO27",
+ "SDA0",
+ "SCL0",
+ "NC", /* GPIO30 */
+ "NC", /* GPIO31 */
+ "CAM_GPIO1", /* GPIO32 */
+ "NC", /* GPIO33 */
+ "NC", /* GPIO34 */
+ "NC", /* GPIO35 */
+ "NC", /* GPIO36 */
+ "NC", /* GPIO37 */
+ "NC", /* GPIO38 */
+ "NC", /* GPIO39 */
+ "NC", /* GPIO40 */
+ "CAM_GPIO0", /* GPIO41 */
+ "NC", /* GPIO42 */
+ "NC", /* GPIO43 */
+ "NC", /* GPIO44 */
+ "NC", /* GPIO45 */
+ "HDMI_HPD_N",
+ "STATUS_LED_N",
+ /* Used by SD Card */
+ "SD_CLK_R",
+ "SD_CMD_R",
+ "SD_DATA0_R",
+ "SD_DATA1_R",
+ "SD_DATA2_R",
+ "SD_DATA3_R";
+
+ pinctrl-0 = <&gpioout &alt0 &i2s_alt0>;
+
+ /* I2S interface */
+ i2s_alt0: i2s_alt0 {
+ brcm,pins = <18 19 20 21>;
+ brcm,function = <BCM2835_FSEL_ALT0>;
+ };
+};
+
+&hdmi {
+ hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_gpio14>;
+ status = "okay";
+};