diff --git a/include/configs/km8309-common.h b/include/configs/km8309-common.h
deleted file mode 100644
index 3bd334c..0000000
--- a/include/configs/km8309-common.h
+++ /dev/null
@@ -1,174 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2012 Keymile AG
- *                    Gerlando Falauto <gerlando.falauto@keymile.com>
- *
- * Based on km8321-common.h, see respective copyright notice for credits
- */
-
-#ifndef __CONFIG_KM8309_COMMON_H
-#define __CONFIG_KM8309_COMMON_H
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_E300		1	/* E300 family */
-#define CONFIG_QE		1	/* Has QE */
-
-#define CONFIG_KM_DEF_ARCH	"arch=ppc_82xx\0"
-
-/* include common defines/options for all 83xx Keymile boards */
-#include "km83xx-common.h"
-
-/* QE microcode/firmware address */
-#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-/* between the u-boot partition and env */
-#ifndef CONFIG_SYS_QE_FW_ADDR
-#define CONFIG_SYS_QE_FW_ADDR   0xF00C0000
-#endif
-
-/*
- * System IO Config
- */
-/* 0x14000180 SICR_1 */
-#define CONFIG_SYS_SICRL (0			\
-		| SICR_1_UART1_UART1RTS		\
-		| SICR_1_I2C_CKSTOP		\
-		| SICR_1_IRQ_A_IRQ		\
-		| SICR_1_IRQ_B_IRQ		\
-		| SICR_1_GPIO_A_GPIO		\
-		| SICR_1_GPIO_B_GPIO		\
-		| SICR_1_GPIO_C_GPIO		\
-		| SICR_1_GPIO_D_GPIO		\
-		| SICR_1_GPIO_E_GPIO		\
-		| SICR_1_GPIO_F_GPIO		\
-		| SICR_1_USB_A_UART2S		\
-		| SICR_1_USB_B_UART2RTS		\
-		| SICR_1_FEC1_FEC1		\
-		| SICR_1_FEC2_FEC2		\
-		)
-
-/* 0x00080400 SICR_2 */
-#define CONFIG_SYS_SICRH (0			\
-		| SICR_2_FEC3_FEC3		\
-		| SICR_2_HDLC1_A_HDLC1		\
-		| SICR_2_ELBC_A_LA		\
-		| SICR_2_ELBC_B_LCLK		\
-		| SICR_2_HDLC2_A_HDLC2		\
-		| SICR_2_USB_D_GPIO		\
-		| SICR_2_PCI_PCI		\
-		| SICR_2_HDLC1_B_HDLC1		\
-		| SICR_2_HDLC1_C_HDLC1		\
-		| SICR_2_HDLC2_B_GPIO		\
-		| SICR_2_HDLC2_C_HDLC2		\
-		| SICR_2_QUIESCE_B		\
-		)
-
-/* GPR_1 */
-#define CONFIG_SYS_GPR1  0x50008060
-
-#define CONFIG_SYS_GP1DIR 0x00000000
-#define CONFIG_SYS_GP1ODR 0x00000000
-#define CONFIG_SYS_GP2DIR 0xFF000000
-#define CONFIG_SYS_GP2ODR 0x00000000
-
-/*
- * Hardware Reset Configuration Word
- */
-#define CONFIG_SYS_HRCW_LOW (\
-	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 | \
-	HRCWL_DDR_TO_SCB_CLK_2X1 | \
-	HRCWL_CSB_TO_CLKIN_2X1 | \
-	HRCWL_CORE_TO_CSB_2X1 | \
-	HRCWL_CE_PLL_VCO_DIV_2 | \
-	HRCWL_CE_TO_PLL_1X3)
-
-#define CONFIG_SYS_HRCW_HIGH (\
-	HRCWH_PCI_AGENT | \
-	HRCWH_PCI_ARBITER_DISABLE | \
-	HRCWH_CORE_ENABLE | \
-	HRCWH_FROM_0X00000100 | \
-	HRCWH_BOOTSEQ_DISABLE | \
-	HRCWH_SW_WATCHDOG_DISABLE | \
-	HRCWH_ROM_LOC_LOCAL_16BIT | \
-	HRCWH_BIG_ENDIAN | \
-	HRCWH_LALE_NORMAL)
-
-#define CONFIG_SYS_DDRCDR (\
-	DDRCDR_EN | \
-	DDRCDR_PZ_MAXZ | \
-	DDRCDR_NZ_MAXZ | \
-	DDRCDR_M_ODR)
-
-#define CONFIG_SYS_DDR_CS0_BNDS		0x0000007f
-#define CONFIG_SYS_DDR_SDRAM_CFG	(SDRAM_CFG_SDRAM_TYPE_DDR2 | \
-					 SDRAM_CFG_32_BE | \
-					 SDRAM_CFG_SREN | \
-					 SDRAM_CFG_HSE)
-
-#define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000
-#define CONFIG_SYS_DDR_CLK_CNTL		(DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-#define CONFIG_SYS_DDR_INTERVAL	((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
-				 (0x200 << SDRAM_INTERVAL_REFINT_SHIFT))
-
-#define CONFIG_SYS_DDR_CS0_CONFIG	(CSCONFIG_EN | CSCONFIG_AP | \
-					 CSCONFIG_ODT_RD_NEVER | \
-					 CSCONFIG_ODT_WR_ONLY_CURRENT | \
-					 CSCONFIG_ROW_BIT_13 | \
-					 CSCONFIG_COL_BIT_10)
-
-#define CONFIG_SYS_DDR_MODE	0x47860242
-#define CONFIG_SYS_DDR_MODE2	0x8080c000
-
-#define CONFIG_SYS_DDR_TIMING_0	((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
-				 (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
-				 (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
-				 (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
-				 (0 << TIMING_CFG0_WWT_SHIFT) | \
-				 (0 << TIMING_CFG0_RRT_SHIFT) | \
-				 (0 << TIMING_CFG0_WRT_SHIFT) | \
-				 (0 << TIMING_CFG0_RWT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_1	((TIMING_CFG1_CASLAT_40) | \
-				 (2 << TIMING_CFG1_WRTORD_SHIFT) | \
-				 (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
-				 (3 << TIMING_CFG1_WRREC_SHIFT) | \
-				 (7 << TIMING_CFG1_REFREC_SHIFT) | \
-				 (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
-				 (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
-				 (3 << TIMING_CFG1_PRETOACT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_2	((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
-				 (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
-				 (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
-				 (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
-				 (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
-				 (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
-				 (5 << TIMING_CFG2_CPO_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_3	0x00000000
-
-#define CONFIG_SYS_KMBEC_FPGA_BASE	0xE8000000
-#define CONFIG_SYS_KMBEC_FPGA_SIZE	128
-
-/* EEprom support */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
-
-/*
- * Local Bus Configuration & Clock Setup
- */
-#define CONFIG_SYS_LCRR_DBYP	0x80000000
-#define CONFIG_SYS_LCRR_EADC	0x00010000
-#define CONFIG_SYS_LCRR_CLKDIV	0x00000002
-
-#define CONFIG_SYS_LBC_LBCR	0x00000000
-
-/*
- * MMU Setup
- */
-#define CONFIG_SYS_IBAT7L	(0)
-#define CONFIG_SYS_IBAT7U	(0)
-#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
-
-#endif /* __CONFIG_KM8309_COMMON_H */
diff --git a/include/configs/km8321-common.h b/include/configs/km8321-common.h
deleted file mode 100644
index a121a44..0000000
--- a/include/configs/km8321-common.h
+++ /dev/null
@@ -1,139 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2006 Freescale Semiconductor, Inc.
- *                    Dave Liu <daveliu@freescale.com>
- *
- * Copyright (C) 2007 Logic Product Development, Inc.
- *                    Peter Barada <peterb@logicpd.com>
- *
- * Copyright (C) 2007 MontaVista Software, Inc.
- *                    Anton Vorontsov <avorontsov@ru.mvista.com>
- *
- * (C) Copyright 2008
- * Heiko Schocher, DENX Software Engineering, hs@denx.de.
- *
- * (C) Copyright 2010
- * Lukas Roggli, KEYMILE Ltd, lukas.roggli@keymile.com
- *
- * (C) Copyright 2010-2011
- * Thomas Reufer, KEYMILE Ltd, thomas.reufer@keymile.com
- */
-
-#ifndef __CONFIG_KM8321_COMMON_H
-#define __CONFIG_KM8321_COMMON_H
-
-/*
- * High Level Configuration Options
- */
-#define CONFIG_QE	/* Has QE */
-#define CONFIG_KM8321	/* Keymile PBEC8321 board specific */
-
-#define CONFIG_KM_DEF_ARCH	"arch=ppc_8xx\0"
-
-/* include common defines/options for all 83xx Keymile boards */
-#include "km83xx-common.h"
-
-/*
- * System IO Config
- */
-#define CONFIG_SYS_SICRL	SICRL_IRQ_CKS
-
-/*
- * Hardware Reset Configuration Word
- */
-#define CONFIG_SYS_HRCW_LOW (\
-	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 | \
-	HRCWL_DDR_TO_SCB_CLK_2X1 | \
-	HRCWL_CSB_TO_CLKIN_2X1 | \
-	HRCWL_CORE_TO_CSB_2_5X1 | \
-	HRCWL_CE_PLL_VCO_DIV_2 | \
-	HRCWL_CE_TO_PLL_1X3)
-
-#define CONFIG_SYS_HRCW_HIGH (\
-	HRCWH_PCI_AGENT | \
-	HRCWH_PCI_ARBITER_DISABLE | \
-	HRCWH_CORE_ENABLE | \
-	HRCWH_FROM_0X00000100 | \
-	HRCWH_BOOTSEQ_DISABLE | \
-	HRCWH_SW_WATCHDOG_DISABLE | \
-	HRCWH_ROM_LOC_LOCAL_16BIT | \
-	HRCWH_BIG_ENDIAN | \
-	HRCWH_LALE_NORMAL)
-
-#define CONFIG_SYS_DDRCDR (\
-	DDRCDR_EN | \
-	DDRCDR_PZ_MAXZ | \
-	DDRCDR_NZ_MAXZ | \
-	DDRCDR_M_ODR)
-
-#define CONFIG_SYS_DDR_CS0_BNDS		0x0000007f
-#define CONFIG_SYS_DDR_SDRAM_CFG	(SDRAM_CFG_SDRAM_TYPE_DDR2 | \
-					 SDRAM_CFG_32_BE | \
-					 SDRAM_CFG_SREN | \
-					 SDRAM_CFG_HSE)
-
-#define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000
-#define CONFIG_SYS_DDR_CLK_CNTL		(DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
-#define CONFIG_SYS_DDR_INTERVAL	((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
-				 (0x200 << SDRAM_INTERVAL_REFINT_SHIFT))
-
-#define CONFIG_SYS_DDR_CS0_CONFIG	(CSCONFIG_EN | CSCONFIG_AP | \
-					 CSCONFIG_ODT_WR_CFG | \
-					 CSCONFIG_ROW_BIT_13 | \
-					 CSCONFIG_COL_BIT_10)
-
-#define CONFIG_SYS_DDR_MODE	0x47860242
-#define CONFIG_SYS_DDR_MODE2	0x8080c000
-
-#define CONFIG_SYS_DDR_TIMING_0	((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
-				 (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
-				 (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
-				 (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
-				 (0 << TIMING_CFG0_WWT_SHIFT) | \
-				 (0 << TIMING_CFG0_RRT_SHIFT) | \
-				 (0 << TIMING_CFG0_WRT_SHIFT) | \
-				 (0 << TIMING_CFG0_RWT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_1	((TIMING_CFG1_CASLAT_40) | \
-				 (2 << TIMING_CFG1_WRTORD_SHIFT) | \
-				 (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
-				 (3 << TIMING_CFG1_WRREC_SHIFT) | \
-				 (7 << TIMING_CFG1_REFREC_SHIFT) | \
-				 (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
-				 (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
-				 (3 << TIMING_CFG1_PRETOACT_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_2	((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
-				 (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
-				 (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
-				 (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
-				 (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
-				 (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
-				 (5 << TIMING_CFG2_CPO_SHIFT))
-
-#define CONFIG_SYS_DDR_TIMING_3	0x00000000
-
-#define CONFIG_SYS_KMBEC_FPGA_BASE	0xE8000000
-#define CONFIG_SYS_KMBEC_FPGA_SIZE	128
-
-/* EEprom support */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
-
-/*
- * Local Bus Configuration & Clock Setup
- */
-#define CONFIG_SYS_LCRR_DBYP	0x80000000
-#define CONFIG_SYS_LCRR_EADC	0x00010000
-#define CONFIG_SYS_LCRR_CLKDIV	0x00000002
-
-#define CONFIG_SYS_LBC_LBCR	0x00000000
-
-/*
- * MMU Setup
- */
-#define CONFIG_SYS_IBAT7L	(0)
-#define CONFIG_SYS_IBAT7U	(0)
-#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
-#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
-
-#endif /* __CONFIG_KM8321_COMMON_H */
diff --git a/include/configs/kmtegr1.h b/include/configs/kmtegr1.h
index 95a1318..27e3905 100644
--- a/include/configs/kmtegr1.h
+++ b/include/configs/kmtegr1.h
@@ -35,8 +35,168 @@
 #define CONFIG_SYS_MAX_NAND_DEVICE		1
 #define NAND_MAX_CHIPS				1
 
-/* include common defines/options for all 8309 Keymile boards */
-#include "km8309-common.h"
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_E300		1	/* E300 family */
+#define CONFIG_QE		1	/* Has QE */
+
+#define CONFIG_KM_DEF_ARCH	"arch=ppc_82xx\0"
+
+/* include common defines/options for all 83xx Keymile boards */
+#include "km83xx-common.h"
+
+/* QE microcode/firmware address */
+#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
+/* between the u-boot partition and env */
+#ifndef CONFIG_SYS_QE_FW_ADDR
+#define CONFIG_SYS_QE_FW_ADDR   0xF00C0000
+#endif
+
+/*
+ * System IO Config
+ */
+/* 0x14000180 SICR_1 */
+#define CONFIG_SYS_SICRL (0			\
+		| SICR_1_UART1_UART1RTS		\
+		| SICR_1_I2C_CKSTOP		\
+		| SICR_1_IRQ_A_IRQ		\
+		| SICR_1_IRQ_B_IRQ		\
+		| SICR_1_GPIO_A_GPIO		\
+		| SICR_1_GPIO_B_GPIO		\
+		| SICR_1_GPIO_C_GPIO		\
+		| SICR_1_GPIO_D_GPIO		\
+		| SICR_1_GPIO_E_GPIO		\
+		| SICR_1_GPIO_F_GPIO		\
+		| SICR_1_USB_A_UART2S		\
+		| SICR_1_USB_B_UART2RTS		\
+		| SICR_1_FEC1_FEC1		\
+		| SICR_1_FEC2_FEC2		\
+		)
+
+/* 0x00080400 SICR_2 */
+#define CONFIG_SYS_SICRH (0			\
+		| SICR_2_FEC3_FEC3		\
+		| SICR_2_HDLC1_A_HDLC1		\
+		| SICR_2_ELBC_A_LA		\
+		| SICR_2_ELBC_B_LCLK		\
+		| SICR_2_HDLC2_A_HDLC2		\
+		| SICR_2_USB_D_GPIO		\
+		| SICR_2_PCI_PCI		\
+		| SICR_2_HDLC1_B_HDLC1		\
+		| SICR_2_HDLC1_C_HDLC1		\
+		| SICR_2_HDLC2_B_GPIO		\
+		| SICR_2_HDLC2_C_HDLC2		\
+		| SICR_2_QUIESCE_B		\
+		)
+
+/* GPR_1 */
+#define CONFIG_SYS_GPR1  0x50008060
+
+#define CONFIG_SYS_GP1DIR 0x00000000
+#define CONFIG_SYS_GP1ODR 0x00000000
+#define CONFIG_SYS_GP2DIR 0xFF000000
+#define CONFIG_SYS_GP2ODR 0x00000000
+
+/*
+ * Hardware Reset Configuration Word
+ */
+#define CONFIG_SYS_HRCW_LOW (\
+	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 | \
+	HRCWL_DDR_TO_SCB_CLK_2X1 | \
+	HRCWL_CSB_TO_CLKIN_2X1 | \
+	HRCWL_CORE_TO_CSB_2X1 | \
+	HRCWL_CE_PLL_VCO_DIV_2 | \
+	HRCWL_CE_TO_PLL_1X3)
+
+#define CONFIG_SYS_HRCW_HIGH (\
+	HRCWH_PCI_AGENT | \
+	HRCWH_PCI_ARBITER_DISABLE | \
+	HRCWH_CORE_ENABLE | \
+	HRCWH_FROM_0X00000100 | \
+	HRCWH_BOOTSEQ_DISABLE | \
+	HRCWH_SW_WATCHDOG_DISABLE | \
+	HRCWH_ROM_LOC_LOCAL_16BIT | \
+	HRCWH_BIG_ENDIAN | \
+	HRCWH_LALE_NORMAL)
+
+#define CONFIG_SYS_DDRCDR (\
+	DDRCDR_EN | \
+	DDRCDR_PZ_MAXZ | \
+	DDRCDR_NZ_MAXZ | \
+	DDRCDR_M_ODR)
+
+#define CONFIG_SYS_DDR_CS0_BNDS		0x0000007f
+#define CONFIG_SYS_DDR_SDRAM_CFG	(SDRAM_CFG_SDRAM_TYPE_DDR2 | \
+					 SDRAM_CFG_32_BE | \
+					 SDRAM_CFG_SREN | \
+					 SDRAM_CFG_HSE)
+
+#define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000
+#define CONFIG_SYS_DDR_CLK_CNTL		(DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
+#define CONFIG_SYS_DDR_INTERVAL	((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
+				 (0x200 << SDRAM_INTERVAL_REFINT_SHIFT))
+
+#define CONFIG_SYS_DDR_CS0_CONFIG	(CSCONFIG_EN | CSCONFIG_AP | \
+					 CSCONFIG_ODT_RD_NEVER | \
+					 CSCONFIG_ODT_WR_ONLY_CURRENT | \
+					 CSCONFIG_ROW_BIT_13 | \
+					 CSCONFIG_COL_BIT_10)
+
+#define CONFIG_SYS_DDR_MODE	0x47860242
+#define CONFIG_SYS_DDR_MODE2	0x8080c000
+
+#define CONFIG_SYS_DDR_TIMING_0	((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
+				 (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
+				 (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
+				 (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
+				 (0 << TIMING_CFG0_WWT_SHIFT) | \
+				 (0 << TIMING_CFG0_RRT_SHIFT) | \
+				 (0 << TIMING_CFG0_WRT_SHIFT) | \
+				 (0 << TIMING_CFG0_RWT_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_1	((TIMING_CFG1_CASLAT_40) | \
+				 (2 << TIMING_CFG1_WRTORD_SHIFT) | \
+				 (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
+				 (3 << TIMING_CFG1_WRREC_SHIFT) | \
+				 (7 << TIMING_CFG1_REFREC_SHIFT) | \
+				 (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
+				 (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
+				 (3 << TIMING_CFG1_PRETOACT_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_2	((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
+				 (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
+				 (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
+				 (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
+				 (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
+				 (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
+				 (5 << TIMING_CFG2_CPO_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_3	0x00000000
+
+#define CONFIG_SYS_KMBEC_FPGA_BASE	0xE8000000
+#define CONFIG_SYS_KMBEC_FPGA_SIZE	128
+
+/* EEprom support */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
+
+/*
+ * Local Bus Configuration & Clock Setup
+ */
+#define CONFIG_SYS_LCRR_DBYP	0x80000000
+#define CONFIG_SYS_LCRR_EADC	0x00010000
+#define CONFIG_SYS_LCRR_CLKDIV	0x00000002
+
+#define CONFIG_SYS_LBC_LBCR	0x00000000
+
+/*
+ * MMU Setup
+ */
+#define CONFIG_SYS_IBAT7L	(0)
+#define CONFIG_SYS_IBAT7U	(0)
+#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
+#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
+
 /* must be after the include because KMBEC_FPGA is otherwise undefined */
 #define CONFIG_SYS_NAND_BASE CONFIG_SYS_KMBEC_FPGA_BASE /* PRIO_BASE_ADDRESS */
 
diff --git a/include/configs/kmvect1.h b/include/configs/kmvect1.h
index 0bbf541..5a0fbcc 100644
--- a/include/configs/kmvect1.h
+++ b/include/configs/kmvect1.h
@@ -26,8 +26,168 @@
 #define CONFIG_KM_BOARD_NAME   "kmvect1"
 /* at end of uboot partition, before env */
 #define CONFIG_SYS_QE_FW_ADDR   0xF00B0000
-/* include common defines/options for all 8309 Keymile boards */
-#include "km8309-common.h"
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_E300		1	/* E300 family */
+#define CONFIG_QE		1	/* Has QE */
+
+#define CONFIG_KM_DEF_ARCH	"arch=ppc_82xx\0"
+
+/* include common defines/options for all 83xx Keymile boards */
+#include "km83xx-common.h"
+
+/* QE microcode/firmware address */
+#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
+/* between the u-boot partition and env */
+#ifndef CONFIG_SYS_QE_FW_ADDR
+#define CONFIG_SYS_QE_FW_ADDR   0xF00C0000
+#endif
+
+/*
+ * System IO Config
+ */
+/* 0x14000180 SICR_1 */
+#define CONFIG_SYS_SICRL (0			\
+		| SICR_1_UART1_UART1RTS		\
+		| SICR_1_I2C_CKSTOP		\
+		| SICR_1_IRQ_A_IRQ		\
+		| SICR_1_IRQ_B_IRQ		\
+		| SICR_1_GPIO_A_GPIO		\
+		| SICR_1_GPIO_B_GPIO		\
+		| SICR_1_GPIO_C_GPIO		\
+		| SICR_1_GPIO_D_GPIO		\
+		| SICR_1_GPIO_E_GPIO		\
+		| SICR_1_GPIO_F_GPIO		\
+		| SICR_1_USB_A_UART2S		\
+		| SICR_1_USB_B_UART2RTS		\
+		| SICR_1_FEC1_FEC1		\
+		| SICR_1_FEC2_FEC2		\
+		)
+
+/* 0x00080400 SICR_2 */
+#define CONFIG_SYS_SICRH (0			\
+		| SICR_2_FEC3_FEC3		\
+		| SICR_2_HDLC1_A_HDLC1		\
+		| SICR_2_ELBC_A_LA		\
+		| SICR_2_ELBC_B_LCLK		\
+		| SICR_2_HDLC2_A_HDLC2		\
+		| SICR_2_USB_D_GPIO		\
+		| SICR_2_PCI_PCI		\
+		| SICR_2_HDLC1_B_HDLC1		\
+		| SICR_2_HDLC1_C_HDLC1		\
+		| SICR_2_HDLC2_B_GPIO		\
+		| SICR_2_HDLC2_C_HDLC2		\
+		| SICR_2_QUIESCE_B		\
+		)
+
+/* GPR_1 */
+#define CONFIG_SYS_GPR1  0x50008060
+
+#define CONFIG_SYS_GP1DIR 0x00000000
+#define CONFIG_SYS_GP1ODR 0x00000000
+#define CONFIG_SYS_GP2DIR 0xFF000000
+#define CONFIG_SYS_GP2ODR 0x00000000
+
+/*
+ * Hardware Reset Configuration Word
+ */
+#define CONFIG_SYS_HRCW_LOW (\
+	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 | \
+	HRCWL_DDR_TO_SCB_CLK_2X1 | \
+	HRCWL_CSB_TO_CLKIN_2X1 | \
+	HRCWL_CORE_TO_CSB_2X1 | \
+	HRCWL_CE_PLL_VCO_DIV_2 | \
+	HRCWL_CE_TO_PLL_1X3)
+
+#define CONFIG_SYS_HRCW_HIGH (\
+	HRCWH_PCI_AGENT | \
+	HRCWH_PCI_ARBITER_DISABLE | \
+	HRCWH_CORE_ENABLE | \
+	HRCWH_FROM_0X00000100 | \
+	HRCWH_BOOTSEQ_DISABLE | \
+	HRCWH_SW_WATCHDOG_DISABLE | \
+	HRCWH_ROM_LOC_LOCAL_16BIT | \
+	HRCWH_BIG_ENDIAN | \
+	HRCWH_LALE_NORMAL)
+
+#define CONFIG_SYS_DDRCDR (\
+	DDRCDR_EN | \
+	DDRCDR_PZ_MAXZ | \
+	DDRCDR_NZ_MAXZ | \
+	DDRCDR_M_ODR)
+
+#define CONFIG_SYS_DDR_CS0_BNDS		0x0000007f
+#define CONFIG_SYS_DDR_SDRAM_CFG	(SDRAM_CFG_SDRAM_TYPE_DDR2 | \
+					 SDRAM_CFG_32_BE | \
+					 SDRAM_CFG_SREN | \
+					 SDRAM_CFG_HSE)
+
+#define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000
+#define CONFIG_SYS_DDR_CLK_CNTL		(DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
+#define CONFIG_SYS_DDR_INTERVAL	((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
+				 (0x200 << SDRAM_INTERVAL_REFINT_SHIFT))
+
+#define CONFIG_SYS_DDR_CS0_CONFIG	(CSCONFIG_EN | CSCONFIG_AP | \
+					 CSCONFIG_ODT_RD_NEVER | \
+					 CSCONFIG_ODT_WR_ONLY_CURRENT | \
+					 CSCONFIG_ROW_BIT_13 | \
+					 CSCONFIG_COL_BIT_10)
+
+#define CONFIG_SYS_DDR_MODE	0x47860242
+#define CONFIG_SYS_DDR_MODE2	0x8080c000
+
+#define CONFIG_SYS_DDR_TIMING_0	((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
+				 (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
+				 (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
+				 (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
+				 (0 << TIMING_CFG0_WWT_SHIFT) | \
+				 (0 << TIMING_CFG0_RRT_SHIFT) | \
+				 (0 << TIMING_CFG0_WRT_SHIFT) | \
+				 (0 << TIMING_CFG0_RWT_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_1	((TIMING_CFG1_CASLAT_40) | \
+				 (2 << TIMING_CFG1_WRTORD_SHIFT) | \
+				 (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
+				 (3 << TIMING_CFG1_WRREC_SHIFT) | \
+				 (7 << TIMING_CFG1_REFREC_SHIFT) | \
+				 (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
+				 (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
+				 (3 << TIMING_CFG1_PRETOACT_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_2	((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
+				 (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
+				 (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
+				 (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
+				 (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
+				 (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
+				 (5 << TIMING_CFG2_CPO_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_3	0x00000000
+
+#define CONFIG_SYS_KMBEC_FPGA_BASE	0xE8000000
+#define CONFIG_SYS_KMBEC_FPGA_SIZE	128
+
+/* EEprom support */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
+
+/*
+ * Local Bus Configuration & Clock Setup
+ */
+#define CONFIG_SYS_LCRR_DBYP	0x80000000
+#define CONFIG_SYS_LCRR_EADC	0x00010000
+#define CONFIG_SYS_LCRR_CLKDIV	0x00000002
+
+#define CONFIG_SYS_LBC_LBCR	0x00000000
+
+/*
+ * MMU Setup
+ */
+#define CONFIG_SYS_IBAT7L	(0)
+#define CONFIG_SYS_IBAT7U	(0)
+#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
+#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
 
 #define CONFIG_SYS_APP1_BASE		0xA0000000
 #define CONFIG_SYS_APP1_SIZE		256 /* Megabytes */
diff --git a/include/configs/suvd3.h b/include/configs/suvd3.h
index 9813739..5fe5f3c 100644
--- a/include/configs/suvd3.h
+++ b/include/configs/suvd3.h
@@ -24,8 +24,120 @@
 
 #define CONFIG_HOSTNAME		"suvd3"
 #define CONFIG_KM_BOARD_NAME   "suvd3"
-/* include common defines/options for all 8321 Keymile boards */
-#include "km8321-common.h"
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_QE	/* Has QE */
+#define CONFIG_KM8321	/* Keymile PBEC8321 board specific */
+
+#define CONFIG_KM_DEF_ARCH	"arch=ppc_8xx\0"
+
+/* include common defines/options for all 83xx Keymile boards */
+#include "km83xx-common.h"
+
+/*
+ * System IO Config
+ */
+#define CONFIG_SYS_SICRL	SICRL_IRQ_CKS
+
+/*
+ * Hardware Reset Configuration Word
+ */
+#define CONFIG_SYS_HRCW_LOW (\
+	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 | \
+	HRCWL_DDR_TO_SCB_CLK_2X1 | \
+	HRCWL_CSB_TO_CLKIN_2X1 | \
+	HRCWL_CORE_TO_CSB_2_5X1 | \
+	HRCWL_CE_PLL_VCO_DIV_2 | \
+	HRCWL_CE_TO_PLL_1X3)
+
+#define CONFIG_SYS_HRCW_HIGH (\
+	HRCWH_PCI_AGENT | \
+	HRCWH_PCI_ARBITER_DISABLE | \
+	HRCWH_CORE_ENABLE | \
+	HRCWH_FROM_0X00000100 | \
+	HRCWH_BOOTSEQ_DISABLE | \
+	HRCWH_SW_WATCHDOG_DISABLE | \
+	HRCWH_ROM_LOC_LOCAL_16BIT | \
+	HRCWH_BIG_ENDIAN | \
+	HRCWH_LALE_NORMAL)
+
+#define CONFIG_SYS_DDRCDR (\
+	DDRCDR_EN | \
+	DDRCDR_PZ_MAXZ | \
+	DDRCDR_NZ_MAXZ | \
+	DDRCDR_M_ODR)
+
+#define CONFIG_SYS_DDR_CS0_BNDS		0x0000007f
+#define CONFIG_SYS_DDR_SDRAM_CFG	(SDRAM_CFG_SDRAM_TYPE_DDR2 | \
+					 SDRAM_CFG_32_BE | \
+					 SDRAM_CFG_SREN | \
+					 SDRAM_CFG_HSE)
+
+#define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000
+#define CONFIG_SYS_DDR_CLK_CNTL		(DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
+#define CONFIG_SYS_DDR_INTERVAL	((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
+				 (0x200 << SDRAM_INTERVAL_REFINT_SHIFT))
+
+#define CONFIG_SYS_DDR_CS0_CONFIG	(CSCONFIG_EN | CSCONFIG_AP | \
+					 CSCONFIG_ODT_WR_CFG | \
+					 CSCONFIG_ROW_BIT_13 | \
+					 CSCONFIG_COL_BIT_10)
+
+#define CONFIG_SYS_DDR_MODE	0x47860242
+#define CONFIG_SYS_DDR_MODE2	0x8080c000
+
+#define CONFIG_SYS_DDR_TIMING_0	((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
+				 (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
+				 (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
+				 (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
+				 (0 << TIMING_CFG0_WWT_SHIFT) | \
+				 (0 << TIMING_CFG0_RRT_SHIFT) | \
+				 (0 << TIMING_CFG0_WRT_SHIFT) | \
+				 (0 << TIMING_CFG0_RWT_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_1	((TIMING_CFG1_CASLAT_40) | \
+				 (2 << TIMING_CFG1_WRTORD_SHIFT) | \
+				 (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
+				 (3 << TIMING_CFG1_WRREC_SHIFT) | \
+				 (7 << TIMING_CFG1_REFREC_SHIFT) | \
+				 (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
+				 (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
+				 (3 << TIMING_CFG1_PRETOACT_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_2	((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
+				 (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
+				 (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
+				 (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
+				 (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
+				 (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
+				 (5 << TIMING_CFG2_CPO_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_3	0x00000000
+
+#define CONFIG_SYS_KMBEC_FPGA_BASE	0xE8000000
+#define CONFIG_SYS_KMBEC_FPGA_SIZE	128
+
+/* EEprom support */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
+
+/*
+ * Local Bus Configuration & Clock Setup
+ */
+#define CONFIG_SYS_LCRR_DBYP	0x80000000
+#define CONFIG_SYS_LCRR_EADC	0x00010000
+#define CONFIG_SYS_LCRR_CLKDIV	0x00000002
+
+#define CONFIG_SYS_LBC_LBCR	0x00000000
+
+/*
+ * MMU Setup
+ */
+#define CONFIG_SYS_IBAT7L	(0)
+#define CONFIG_SYS_IBAT7U	(0)
+#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
+#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
 
 #define CONFIG_SYS_APP1_BASE		0xA0000000
 #define CONFIG_SYS_APP1_SIZE		256 /* Megabytes */
diff --git a/include/configs/tuxx1.h b/include/configs/tuxx1.h
index 0b17084..c031661 100644
--- a/include/configs/tuxx1.h
+++ b/include/configs/tuxx1.h
@@ -42,8 +42,119 @@
 #error ("Board not supported")
 #endif
 
-/* include common defines/options for all 8321 Keymile boards */
-#include "km8321-common.h"
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_QE	/* Has QE */
+#define CONFIG_KM8321	/* Keymile PBEC8321 board specific */
+
+#define CONFIG_KM_DEF_ARCH	"arch=ppc_8xx\0"
+
+/* include common defines/options for all 83xx Keymile boards */
+#include "km83xx-common.h"
+
+/*
+ * System IO Config
+ */
+#define CONFIG_SYS_SICRL	SICRL_IRQ_CKS
+
+/*
+ * Hardware Reset Configuration Word
+ */
+#define CONFIG_SYS_HRCW_LOW (\
+	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 | \
+	HRCWL_DDR_TO_SCB_CLK_2X1 | \
+	HRCWL_CSB_TO_CLKIN_2X1 | \
+	HRCWL_CORE_TO_CSB_2_5X1 | \
+	HRCWL_CE_PLL_VCO_DIV_2 | \
+	HRCWL_CE_TO_PLL_1X3)
+
+#define CONFIG_SYS_HRCW_HIGH (\
+	HRCWH_PCI_AGENT | \
+	HRCWH_PCI_ARBITER_DISABLE | \
+	HRCWH_CORE_ENABLE | \
+	HRCWH_FROM_0X00000100 | \
+	HRCWH_BOOTSEQ_DISABLE | \
+	HRCWH_SW_WATCHDOG_DISABLE | \
+	HRCWH_ROM_LOC_LOCAL_16BIT | \
+	HRCWH_BIG_ENDIAN | \
+	HRCWH_LALE_NORMAL)
+
+#define CONFIG_SYS_DDRCDR (\
+	DDRCDR_EN | \
+	DDRCDR_PZ_MAXZ | \
+	DDRCDR_NZ_MAXZ | \
+	DDRCDR_M_ODR)
+
+#define CONFIG_SYS_DDR_CS0_BNDS		0x0000007f
+#define CONFIG_SYS_DDR_SDRAM_CFG	(SDRAM_CFG_SDRAM_TYPE_DDR2 | \
+					 SDRAM_CFG_32_BE | \
+					 SDRAM_CFG_SREN | \
+					 SDRAM_CFG_HSE)
+
+#define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000
+#define CONFIG_SYS_DDR_CLK_CNTL		(DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
+#define CONFIG_SYS_DDR_INTERVAL	((0x064 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
+				 (0x200 << SDRAM_INTERVAL_REFINT_SHIFT))
+
+#define CONFIG_SYS_DDR_CS0_CONFIG	(CSCONFIG_EN | CSCONFIG_AP | \
+					 CSCONFIG_ODT_WR_CFG | \
+					 CSCONFIG_ROW_BIT_13 | \
+					 CSCONFIG_COL_BIT_10)
+
+#define CONFIG_SYS_DDR_MODE	0x47860242
+#define CONFIG_SYS_DDR_MODE2	0x8080c000
+
+#define CONFIG_SYS_DDR_TIMING_0	((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
+				 (8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
+				 (2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
+				 (2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
+				 (0 << TIMING_CFG0_WWT_SHIFT) | \
+				 (0 << TIMING_CFG0_RRT_SHIFT) | \
+				 (0 << TIMING_CFG0_WRT_SHIFT) | \
+				 (0 << TIMING_CFG0_RWT_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_1	((TIMING_CFG1_CASLAT_40) | \
+				 (2 << TIMING_CFG1_WRTORD_SHIFT) | \
+				 (2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
+				 (3 << TIMING_CFG1_WRREC_SHIFT) | \
+				 (7 << TIMING_CFG1_REFREC_SHIFT) | \
+				 (3 << TIMING_CFG1_ACTTORW_SHIFT) | \
+				 (7 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
+				 (3 << TIMING_CFG1_PRETOACT_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_2	((8 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
+				 (3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
+				 (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
+				 (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
+				 (3 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
+				 (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
+				 (5 << TIMING_CFG2_CPO_SHIFT))
+
+#define CONFIG_SYS_DDR_TIMING_3	0x00000000
+
+#define CONFIG_SYS_KMBEC_FPGA_BASE	0xE8000000
+#define CONFIG_SYS_KMBEC_FPGA_SIZE	128
+
+/* EEprom support */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
+
+/*
+ * Local Bus Configuration & Clock Setup
+ */
+#define CONFIG_SYS_LCRR_DBYP	0x80000000
+#define CONFIG_SYS_LCRR_EADC	0x00010000
+#define CONFIG_SYS_LCRR_CLKDIV	0x00000002
+
+#define CONFIG_SYS_LBC_LBCR	0x00000000
+
+/*
+ * MMU Setup
+ */
+#define CONFIG_SYS_IBAT7L	(0)
+#define CONFIG_SYS_IBAT7U	(0)
+#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
+#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
 
 #define CONFIG_SYS_APP1_BASE	0xA0000000    /* PAXG */
 #define	CONFIG_SYS_APP1_SIZE	256 /* Megabytes */