ARM: dts: add support for Odroid-N2

Import HardKernel Odroid-N2 DT from Linux 5.3-rc1, commit 5f9e832c1370
("Linus 5.3-rc1") based on an Amlogic G12B S922X SoC.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index b437f75..70a9bc2 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -135,7 +135,8 @@
 	meson-gxl-s905x-khadas-vim.dtb \
 	meson-gxm-khadas-vim2.dtb \
 	meson-axg-s400.dtb \
-	meson-g12a-u200.dtb
+	meson-g12a-u200.dtb \
+	meson-g12b-odroid-n2.dtb
 dtb-$(CONFIG_TEGRA) += tegra20-harmony.dtb \
 	tegra20-medcom-wide.dtb \
 	tegra20-paz00.dtb \
diff --git a/arch/arm/dts/meson-g12b-odroid-n2.dts b/arch/arm/dts/meson-g12b-odroid-n2.dts
new file mode 100644
index 0000000..81780ff
--- /dev/null
+++ b/arch/arm/dts/meson-g12b-odroid-n2.dts
@@ -0,0 +1,386 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+/dts-v1/;
+
+#include "meson-g12b.dtsi"
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/meson-g12a-gpio.h>
+#include <dt-bindings/sound/meson-g12a-tohdmitx.h>
+
+/ {
+	compatible = "hardkernel,odroid-n2", "amlogic,g12b";
+	model = "Hardkernel ODROID-N2";
+
+	aliases {
+		serial0 = &uart_AO;
+		ethernet0 = &ethmac;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x40000000>;
+	};
+
+	emmc_pwrseq: emmc-pwrseq {
+		compatible = "mmc-pwrseq-emmc";
+		reset-gpios = <&gpio BOOT_12 GPIO_ACTIVE_LOW>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		blue {
+			label = "n2:blue";
+			gpios = <&gpio_ao GPIOAO_11 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	tflash_vdd: regulator-tflash_vdd {
+		compatible = "regulator-fixed";
+
+		regulator-name = "TFLASH_VDD";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&gpio_ao GPIOAO_8 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	tf_io: gpio-regulator-tf_io {
+		compatible = "regulator-gpio";
+
+		regulator-name = "TF_IO";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&gpio_ao GPIOAO_9 GPIO_ACTIVE_HIGH>;
+		gpios-states = <0>;
+
+		states = <3300000 0
+			  1800000 1>;
+	};
+
+	flash_1v8: regulator-flash_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "FLASH_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_3v3>;
+		regulator-always-on;
+	};
+
+	main_12v: regulator-main_12v {
+		compatible = "regulator-fixed";
+		regulator-name = "12V";
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+		regulator-always-on;
+	};
+
+	vcc_5v: regulator-vcc_5v {
+		compatible = "regulator-fixed";
+		regulator-name = "5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		vin-supply = <&main_12v>;
+	};
+
+	vcc_1v8: regulator-vcc_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_3v3>;
+		regulator-always-on;
+	};
+
+	vcc_3v3: regulator-vcc_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+		/* FIXME: actually controlled by VDDCPU_B_EN */
+	};
+
+	hub_5v: regulator-hub_5v {
+		compatible = "regulator-fixed";
+		regulator-name = "HUB_5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc_5v>;
+
+		/* Connected to the Hub CHIPENABLE, LOW sets low power state */
+		gpio = <&gpio GPIOH_5 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	usb_pwr_en: regulator-usb_pwr_en {
+		compatible = "regulator-fixed";
+		regulator-name = "USB_PWR_EN";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc_5v>;
+
+		/* Connected to the microUSB port power enable */
+		gpio = <&gpio GPIOH_6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	vddao_1v8: regulator-vddao_1v8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vddao_3v3>;
+		regulator-always-on;
+	};
+
+	vddao_3v3: regulator-vddao_3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDDAO_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&main_12v>;
+		regulator-always-on;
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_connector_in: endpoint {
+				remote-endpoint = <&hdmi_tx_tmds_out>;
+			};
+		};
+	};
+
+	sound {
+		compatible = "amlogic,axg-sound-card";
+		model = "G12A-ODROIDN2";
+		audio-aux-devs = <&tdmout_b>;
+		audio-routing = "TDMOUT_B IN 0", "FRDDR_A OUT 1",
+				"TDMOUT_B IN 1", "FRDDR_B OUT 1",
+				"TDMOUT_B IN 2", "FRDDR_C OUT 1",
+				"TDM_B Playback", "TDMOUT_B OUT";
+
+		assigned-clocks = <&clkc CLKID_MPLL2>,
+				  <&clkc CLKID_MPLL0>,
+				  <&clkc CLKID_MPLL1>;
+		assigned-clock-parents = <0>, <0>, <0>;
+		assigned-clock-rates = <294912000>,
+				       <270950400>,
+				       <393216000>;
+		status = "okay";
+
+		dai-link-0 {
+			sound-dai = <&frddr_a>;
+		};
+
+		dai-link-1 {
+			sound-dai = <&frddr_b>;
+		};
+
+		dai-link-2 {
+			sound-dai = <&frddr_c>;
+		};
+
+		/* 8ch hdmi interface */
+		dai-link-3 {
+			sound-dai = <&tdmif_b>;
+			dai-format = "i2s";
+			dai-tdm-slot-tx-mask-0 = <1 1>;
+			dai-tdm-slot-tx-mask-1 = <1 1>;
+			dai-tdm-slot-tx-mask-2 = <1 1>;
+			dai-tdm-slot-tx-mask-3 = <1 1>;
+			mclk-fs = <256>;
+
+			codec {
+				sound-dai = <&tohdmitx TOHDMITX_I2S_IN_B>;
+			};
+		};
+
+		/* hdmi glue */
+		dai-link-4 {
+			sound-dai = <&tohdmitx TOHDMITX_I2S_OUT>;
+
+			codec {
+				sound-dai = <&hdmi_tx>;
+			};
+		};
+	};
+};
+
+&arb {
+	status = "okay";
+};
+
+&cec_AO {
+	pinctrl-0 = <&cec_ao_a_h_pins>;
+	pinctrl-names = "default";
+	status = "disabled";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&cecb_AO {
+	pinctrl-0 = <&cec_ao_b_h_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	hdmi-phandle = <&hdmi_tx>;
+};
+
+&clkc_audio {
+	status = "okay";
+};
+
+&ext_mdio {
+	external_phy: ethernet-phy@0 {
+		/* Realtek RTL8211F (0x001cc916) */	
+		reg = <0>;
+		max-speed = <1000>;
+
+		reset-assert-us = <10000>;
+		reset-deassert-us = <30000>;
+		reset-gpios = <&gpio GPIOZ_15 (GPIO_ACTIVE_LOW | GPIO_OPEN_DRAIN)>;
+
+		interrupt-parent = <&gpio_intc>;
+		/* MAC_INTR on GPIOZ_14 */
+		interrupts = <26 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&ethmac {
+	pinctrl-0 = <&eth_pins>, <&eth_rgmii_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+	phy-mode = "rgmii";
+	phy-handle = <&external_phy>;
+	amlogic,tx-delay-ns = <2>;
+};
+
+&frddr_a {
+	status = "okay";
+};
+
+&frddr_b {
+	status = "okay";
+};
+
+&frddr_c {
+	status = "okay";
+};
+
+&gpio {
+	/*
+	 * WARNING: The USB Hub on the Odroid-N2 needs a reset signal
+	 * to be turned high in order to be detected by the USB Controller
+	 * This signal should be handled by a USB specific power sequence
+	 * in order to reset the Hub when USB bus is powered down.
+	 */
+	usb-hub {
+		gpio-hog;
+		gpios = <GPIOH_4 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "usb-hub-reset";
+	};
+};
+
+&hdmi_tx {
+	status = "okay";
+	pinctrl-0 = <&hdmitx_hpd_pins>, <&hdmitx_ddc_pins>;
+	pinctrl-names = "default";
+	hdmi-supply = <&vcc_5v>;
+};
+
+&hdmi_tx_tmds_port {
+	hdmi_tx_tmds_out: endpoint {
+		remote-endpoint = <&hdmi_connector_in>;
+	};
+};
+
+&ir {
+	status = "okay";
+	pinctrl-0 = <&remote_input_ao_pins>;
+	pinctrl-names = "default";
+};
+
+/* SD card */
+&sd_emmc_b {
+	status = "okay";
+	pinctrl-0 = <&sdcard_c_pins>;
+	pinctrl-1 = <&sdcard_clk_gate_c_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <4>;
+	cap-sd-highspeed;
+	max-frequency = <50000000>;
+	disable-wp;
+
+	cd-gpios = <&gpio GPIOC_6 GPIO_ACTIVE_LOW>;
+	vmmc-supply = <&tflash_vdd>;
+	vqmmc-supply = <&tf_io>;
+
+};
+
+/* eMMC */
+&sd_emmc_c {
+	status = "okay";
+	pinctrl-0 = <&emmc_pins>, <&emmc_ds_pins>;
+	pinctrl-1 = <&emmc_clk_gate_pins>;
+	pinctrl-names = "default", "clk-gate";
+
+	bus-width = <8>;
+	cap-mmc-highspeed;
+	mmc-ddr-1_8v;
+	mmc-hs200-1_8v;
+	max-frequency = <200000000>;
+	disable-wp;
+
+	mmc-pwrseq = <&emmc_pwrseq>;
+	vmmc-supply = <&vcc_3v3>;
+	vqmmc-supply = <&flash_1v8>;
+};
+
+&tdmif_b {
+	status = "okay";
+};
+
+&tdmout_b {
+	status = "okay";
+};
+
+&tohdmitx {
+	status = "okay";
+};
+
+&uart_AO {
+	status = "okay";
+	pinctrl-0 = <&uart_ao_a_pins>;
+	pinctrl-names = "default";
+};
+
+&usb {
+	status = "okay";
+	vbus-supply = <&usb_pwr_en>;
+};
+
+&usb2_phy0 {
+	phy-supply = <&vcc_5v>;
+};
+
+&usb2_phy1 {
+	/* Enable the hub which is connected to this port */
+	phy-supply = <&hub_5v>;
+};
diff --git a/arch/arm/dts/meson-g12b.dtsi b/arch/arm/dts/meson-g12b.dtsi
new file mode 100644
index 0000000..9e88e51
--- /dev/null
+++ b/arch/arm/dts/meson-g12b.dtsi
@@ -0,0 +1,82 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2019 BayLibre, SAS
+ * Author: Neil Armstrong <narmstrong@baylibre.com>
+ */
+
+#include "meson-g12a.dtsi"
+
+/ {
+	compatible = "amlogic,g12b";
+
+	cpus {
+		cpu-map {
+			cluster0 {
+				core0 {
+					cpu = <&cpu0>;
+				};
+
+				core1 {
+					cpu = <&cpu1>;
+				};
+			};
+
+			cluster1 {
+				core0 {
+					cpu = <&cpu100>;
+				};
+
+				core1 {
+					cpu = <&cpu101>;
+				};
+
+				core2 {
+					cpu = <&cpu102>;
+				};
+
+				core3 {
+					cpu = <&cpu103>;
+				};
+			};
+		};
+
+		/delete-node/ cpu@2;
+		/delete-node/ cpu@3;
+
+		cpu100: cpu@100 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a73";
+			reg = <0x0 0x100>;
+			enable-method = "psci";
+			next-level-cache = <&l2>;
+		};
+
+		cpu101: cpu@101 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a73";
+			reg = <0x0 0x101>;
+			enable-method = "psci";
+			next-level-cache = <&l2>;
+		};
+
+		cpu102: cpu@102 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a73";
+			reg = <0x0 0x102>;
+			enable-method = "psci";
+			next-level-cache = <&l2>;
+		};
+
+		cpu103: cpu@103 {
+			device_type = "cpu";
+			compatible = "arm,cortex-a73";
+			reg = <0x0 0x103>;
+			enable-method = "psci";
+			next-level-cache = <&l2>;
+		};
+	};
+};
+
+&clkc {
+	compatible = "amlogic,g12b-clkc";
+};
diff --git a/include/dt-bindings/sound/meson-g12a-tohdmitx.h b/include/dt-bindings/sound/meson-g12a-tohdmitx.h
new file mode 100644
index 0000000..c5e1f48
--- /dev/null
+++ b/include/dt-bindings/sound/meson-g12a-tohdmitx.h
@@ -0,0 +1,13 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __DT_MESON_G12A_TOHDMITX_H
+#define __DT_MESON_G12A_TOHDMITX_H
+
+#define TOHDMITX_I2S_IN_A	0
+#define TOHDMITX_I2S_IN_B	1
+#define TOHDMITX_I2S_IN_C	2
+#define TOHDMITX_I2S_OUT	3
+#define TOHDMITX_SPDIF_IN_A	4
+#define TOHDMITX_SPDIF_IN_B	5
+#define TOHDMITX_SPDIF_OUT	6
+
+#endif /* __DT_MESON_G12A_TOHDMITX_H */