/* SPDX-License-Identifier: GPL-2.0+ */
/*
 * Copyright 2003-2004 Red Hat, Inc.  All rights reserved.
 * Copyright 2003-2004 Jeff Garzik
 * Copyright (C) 2008 Freescale Semiconductor, Inc.
 *		Dave Liu <daveliu@freescale.com>
 *		port from libata of linux kernel
 */

#ifndef __LIBATA_H__
#define __LIBATA_H__

#include <linux/types.h>

enum {
	/* various global constants */
	ATA_MAX_DEVICES		= 2,	/* per bus/port */
	ATA_MAX_PRD		= 256,	/* we could make these 256/256 */
	ATA_SECT_SIZE		= 512,
	ATA_MAX_SECTORS_128	= 128,
	ATA_MAX_SECTORS		= 256,
	ATA_MAX_SECTORS_LBA48	= 65535,
	ATA_MAX_SECTORS_TAPE	= 65535,

	ATA_ID_WORDS		= 256,
	ATA_ID_SERNO		= 10,
	ATA_ID_FW_REV		= 23,
	ATA_ID_PROD		= 27,
	ATA_ID_OLD_PIO_MODES	= 51,
	ATA_ID_FIELD_VALID	= 53,
	ATA_ID_LBA_SECTORS	= 60,
	ATA_ID_MWDMA_MODES	= 63,
	ATA_ID_PIO_MODES	= 64,
	ATA_ID_EIDE_DMA_MIN	= 65,
	ATA_ID_EIDE_PIO		= 67,
	ATA_ID_EIDE_PIO_IORDY	= 68,
	ATA_ID_PIO4		= (1 << 1),
	ATA_ID_QUEUE_DEPTH	= 75,
	ATA_ID_SATA_CAP		= 76,
	ATA_ID_SATA_FEATURES	= 78,
	ATA_ID_SATA_FEATURES_EN	= 79,
	ATA_ID_MAJOR_VER	= 80,
	ATA_ID_MINOR_VER	= 81,
	ATA_ID_UDMA_MODES	= 88,
	ATA_ID_LBA48_SECTORS	= 100,

	ATA_ID_SERNO_LEN	= 20,
	ATA_ID_FW_REV_LEN	= 8,
	ATA_ID_PROD_LEN		= 40,

	ATA_PCI_CTL_OFS		= 2,

	ATA_PIO0		= (1 << 0),
	ATA_PIO1		= ATA_PIO0 | (1 << 1),
	ATA_PIO2		= ATA_PIO1 | (1 << 2),
	ATA_PIO3		= ATA_PIO2 | (1 << 3),
	ATA_PIO4		= ATA_PIO3 | (1 << 4),
	ATA_PIO5		= ATA_PIO4 | (1 << 5),
	ATA_PIO6		= ATA_PIO5 | (1 << 6),

	ATA_SWDMA0		= (1 << 0),
	ATA_SWDMA1		= ATA_SWDMA0 | (1 << 1),
	ATA_SWDMA2		= ATA_SWDMA1 | (1 << 2),

	ATA_SWDMA2_ONLY		= (1 << 2),

	ATA_MWDMA0		= (1 << 0),
	ATA_MWDMA1		= ATA_MWDMA0 | (1 << 1),
	ATA_MWDMA2		= ATA_MWDMA1 | (1 << 2),

	ATA_MWDMA12_ONLY	= (1 << 1) | (1 << 2),
	ATA_MWDMA2_ONLY		= (1 << 2),

	ATA_UDMA0		= (1 << 0),
	ATA_UDMA1		= ATA_UDMA0 | (1 << 1),
	ATA_UDMA2		= ATA_UDMA1 | (1 << 2),
	ATA_UDMA3		= ATA_UDMA2 | (1 << 3),
	ATA_UDMA4		= ATA_UDMA3 | (1 << 4),
	ATA_UDMA5		= ATA_UDMA4 | (1 << 5),
	ATA_UDMA6		= ATA_UDMA5 | (1 << 6),
	ATA_UDMA7		= ATA_UDMA6 | (1 << 7),
	/* ATA_UDMA7 is just for completeness... doesn't exist (yet?).  */

	ATA_UDMA_MASK_40C	= ATA_UDMA2,	/* udma0-2 */

	/* DMA-related */
	ATA_PRD_SZ		= 8,
	ATA_PRD_TBL_SZ		= (ATA_MAX_PRD * ATA_PRD_SZ),
	ATA_PRD_EOT		= (1 << 31),	/* end-of-table flag */

	ATA_DMA_TABLE_OFS	= 4,
	ATA_DMA_STATUS		= 2,
	ATA_DMA_CMD		= 0,
	ATA_DMA_WR		= (1 << 3),
	ATA_DMA_START		= (1 << 0),
	ATA_DMA_INTR		= (1 << 2),
	ATA_DMA_ERR		= (1 << 1),
	ATA_DMA_ACTIVE		= (1 << 0),

	/* bits in ATA command block registers */
	ATA_HOB			= (1 << 7),	/* LBA48 selector */
	ATA_NIEN		= (1 << 1),	/* disable-irq flag */
	ATA_LBA			= (1 << 6),	/* LBA28 selector */
	ATA_DEV1		= (1 << 4),	/* Select Device 1 (slave) */
	ATA_DEVICE_OBS		= (1 << 7) | (1 << 5), /* obs bits in dev reg */
	ATA_DEVCTL_OBS		= (1 << 3),	/* obsolete bit in devctl reg */
	ATA_BUSY		= (1 << 7),	/* BSY status bit */
	ATA_DRDY		= (1 << 6),	/* device ready */
	ATA_DF			= (1 << 5),	/* device fault */
	ATA_DRQ			= (1 << 3),	/* data request i/o */
	ATA_ERR			= (1 << 0),	/* have an error */
	ATA_SRST		= (1 << 2),	/* software reset */
	ATA_ICRC		= (1 << 7),	/* interface CRC error */
	ATA_UNC			= (1 << 6),	/* uncorrectable media error */
	ATA_IDNF		= (1 << 4),	/* ID not found */
	ATA_ABORTED		= (1 << 2),	/* command aborted */

	/* ATA command block registers */
	ATA_REG_DATA		= 0x00,
	ATA_REG_ERR		= 0x01,
	ATA_REG_NSECT		= 0x02,
	ATA_REG_LBAL		= 0x03,
	ATA_REG_LBAM		= 0x04,
	ATA_REG_LBAH		= 0x05,
	ATA_REG_DEVICE		= 0x06,
	ATA_REG_STATUS		= 0x07,

	ATA_REG_FEATURE		= ATA_REG_ERR, /* and their aliases */
	ATA_REG_CMD		= ATA_REG_STATUS,
	ATA_REG_BYTEL		= ATA_REG_LBAM,
	ATA_REG_BYTEH		= ATA_REG_LBAH,
	ATA_REG_DEVSEL		= ATA_REG_DEVICE,
	ATA_REG_IRQ		= ATA_REG_NSECT,

	/* ATA device commands */
	ATA_CMD_DEV_RESET	    = 0x08, /* ATAPI device reset */
	ATA_CMD_PIO_READ	    = 0x20, /* Read sectors with retry */
	ATA_CMD_PIO_READ_EXT	    = 0x24,
	ATA_CMD_READ_EXT	    = 0x25,
	ATA_CMD_READ_NATIVE_MAX_EXT = 0x27,
	ATA_CMD_READ_MULTI_EXT	    = 0x29,
	ATA_CMD_READ_LOG_EXT	    = 0x2f,
	ATA_CMD_PIO_WRITE	    = 0x30, /* write sectors with retry */
	ATA_CMD_PIO_WRITE_EXT	    = 0x34,
	ATA_CMD_WRITE_EXT	    = 0x35,
	ATA_CMD_SET_MAX_EXT	    = 0x37,
	ATA_CMD_WRITE_MULTI_EXT	    = 0x39,
	ATA_CMD_WRITE_FUA_EXT	    = 0x3D,
	ATA_CMD_VERIFY		    = 0x40, /* read verify sectors with retry */
	ATA_CMD_VERIFY_EXT	    = 0x42,
	ATA_CMD_FPDMA_READ	    = 0x60,
	ATA_CMD_FPDMA_WRITE	    = 0x61,
	ATA_CMD_EDD		    = 0x90, /* execute device diagnostic */
	ATA_CMD_INIT_DEV_PARAMS	    = 0x91, /* initialize device parameters */
	ATA_CMD_PACKET		    = 0xA0, /* ATAPI packet */
	ATA_CMD_ID_ATAPI	    = 0xA1, /* ATAPI identify device */
	ATA_CMD_CONF_OVERLAY	    = 0xB1,
	ATA_CMD_READ_MULTI	    = 0xC4, /* read multiple */
	ATA_CMD_WRITE_MULTI	    = 0xC5, /* write multiple */
	ATA_CMD_SET_MULTI	    = 0xC6, /* set multiple mode */
	ATA_CMD_READ		    = 0xC8, /* read DMA with retry */
	ATA_CMD_WRITE		    = 0xCA, /* write DMA with retry */
	ATA_CMD_WRITE_MULTI_FUA_EXT = 0xCE,
	ATA_CMD_STANDBYNOW1	    = 0xE0, /* standby immediate */
	ATA_CMD_IDLEIMMEDIATE	    = 0xE1, /* idle immediate */
	ATA_CMD_STANDBY		    = 0xE2, /* place in standby power mode */
	ATA_CMD_IDLE		    = 0xE3, /* place in idle power mode */
	ATA_CMD_PMP_READ	    = 0xE4, /* read buffer */
	ATA_CMD_CHK_POWER	    = 0xE5, /* check power mode */
	ATA_CMD_SLEEP		    = 0xE6, /* sleep */
	ATA_CMD_FLUSH		    = 0xE7,
	ATA_CMD_PMP_WRITE	    = 0xE8, /* write buffer */
	ATA_CMD_FLUSH_EXT	    = 0xEA,
	ATA_CMD_ID_ATA		    = 0xEC, /* identify device */
	ATA_CMD_SET_FEATURES	    = 0xEF, /* set features */
	ATA_CMD_SEC_FREEZE_LOCK	    = 0xF5, /* security freeze */
	ATA_CMD_READ_NATIVE_MAX	    = 0xF8,
	ATA_CMD_SET_MAX		    = 0xF9,

	/* READ_LOG_EXT pages */
	ATA_LOG_SATA_NCQ	= 0x10,

	/* READ/WRITE LONG (obsolete) */
	ATA_CMD_READ_LONG	= 0x22,
	ATA_CMD_READ_LONG_ONCE	= 0x23,
	ATA_CMD_WRITE_LONG	= 0x32,
	ATA_CMD_WRITE_LONG_ONCE	= 0x33,

	/* SETFEATURES stuff */
	SETFEATURES_XFER	= 0x03,
	XFER_UDMA_7		= 0x47,
	XFER_UDMA_6		= 0x46,
	XFER_UDMA_5		= 0x45,
	XFER_UDMA_4		= 0x44,
	XFER_UDMA_3		= 0x43,
	XFER_UDMA_2		= 0x42,
	XFER_UDMA_1		= 0x41,
	XFER_UDMA_0		= 0x40,
	XFER_MW_DMA_4		= 0x24,	/* CFA only */
	XFER_MW_DMA_3		= 0x23,	/* CFA only */
	XFER_MW_DMA_2		= 0x22,
	XFER_MW_DMA_1		= 0x21,
	XFER_MW_DMA_0		= 0x20,
	XFER_SW_DMA_2		= 0x12,
	XFER_SW_DMA_1		= 0x11,
	XFER_SW_DMA_0		= 0x10,
	XFER_PIO_6		= 0x0E,	/* CFA only */
	XFER_PIO_5		= 0x0D,	/* CFA only */
	XFER_PIO_4		= 0x0C,
	XFER_PIO_3		= 0x0B,
	XFER_PIO_2		= 0x0A,
	XFER_PIO_1		= 0x09,
	XFER_PIO_0		= 0x08,
	XFER_PIO_SLOW		= 0x00,

	SETFEATURES_WC_ON	= 0x02, /* Enable write cache */
	SETFEATURES_WC_OFF	= 0x82, /* Disable write cache */

	SETFEATURES_SPINUP	= 0x07, /* Spin-up drive */

	SETFEATURES_SATA_ENABLE = 0x10, /* Enable use of SATA feature */
	SETFEATURES_SATA_DISABLE = 0x90, /* Disable use of SATA feature */

	/* SETFEATURE Sector counts for SATA features */
	SATA_AN			= 0x05,  /* Asynchronous Notification */
	SATA_DIPM		= 0x03,  /* Device Initiated Power Management */

	/* feature values for SET_MAX */
	ATA_SET_MAX_ADDR	= 0x00,
	ATA_SET_MAX_PASSWD	= 0x01,
	ATA_SET_MAX_LOCK	= 0x02,
	ATA_SET_MAX_UNLOCK	= 0x03,
	ATA_SET_MAX_FREEZE_LOCK	= 0x04,

	/* feature values for DEVICE CONFIGURATION OVERLAY */
	ATA_DCO_RESTORE		= 0xC0,
	ATA_DCO_FREEZE_LOCK	= 0xC1,
	ATA_DCO_IDENTIFY	= 0xC2,
	ATA_DCO_SET		= 0xC3,

	/* ATAPI stuff */
	ATAPI_PKT_DMA		= (1 << 0),
	ATAPI_DMADIR		= (1 << 2),	/* ATAPI data dir:
						   0=to device, 1=to host */
	ATAPI_CDB_LEN		= 16,

	/* PMP stuff */
	SATA_PMP_MAX_PORTS	= 15,
	SATA_PMP_CTRL_PORT	= 15,

	SATA_PMP_GSCR_DWORDS	= 128,
	SATA_PMP_GSCR_PROD_ID	= 0,
	SATA_PMP_GSCR_REV	= 1,
	SATA_PMP_GSCR_PORT_INFO	= 2,
	SATA_PMP_GSCR_ERROR	= 32,
	SATA_PMP_GSCR_ERROR_EN	= 33,
	SATA_PMP_GSCR_FEAT	= 64,
	SATA_PMP_GSCR_FEAT_EN	= 96,

	SATA_PMP_PSCR_STATUS	= 0,
	SATA_PMP_PSCR_ERROR	= 1,
	SATA_PMP_PSCR_CONTROL	= 2,

	SATA_PMP_FEAT_BIST	= (1 << 0),
	SATA_PMP_FEAT_PMREQ	= (1 << 1),
	SATA_PMP_FEAT_DYNSSC	= (1 << 2),
	SATA_PMP_FEAT_NOTIFY	= (1 << 3),

	/* cable types */
	ATA_CBL_NONE		= 0,
	ATA_CBL_PATA40		= 1,
	ATA_CBL_PATA80		= 2,
	ATA_CBL_PATA40_SHORT	= 3,	/* 40 wire cable to high UDMA spec */
	ATA_CBL_PATA_UNK	= 4,	/* don't know, maybe 80c? */
	ATA_CBL_PATA_IGN	= 5,	/* don't know, ignore cable handling */
	ATA_CBL_SATA		= 6,

	/* SATA Status and Control Registers */
	SCR_STATUS		= 0,
	SCR_ERROR		= 1,
	SCR_CONTROL		= 2,
	SCR_ACTIVE		= 3,
	SCR_NOTIFICATION	= 4,

	/* SError bits */
	SERR_DATA_RECOVERED	= (1 << 0), /* recovered data error */
	SERR_COMM_RECOVERED	= (1 << 1), /* recovered comm failure */
	SERR_DATA		= (1 << 8), /* unrecovered data error */
	SERR_PERSISTENT		= (1 << 9), /* persistent data/comm error */
	SERR_PROTOCOL		= (1 << 10), /* protocol violation */
	SERR_INTERNAL		= (1 << 11), /* host internal error */
	SERR_PHYRDY_CHG		= (1 << 16), /* PHY RDY changed */
	SERR_PHY_INT_ERR	= (1 << 17), /* PHY internal error */
	SERR_COMM_WAKE		= (1 << 18), /* Comm wake */
	SERR_10B_8B_ERR		= (1 << 19), /* 10b to 8b decode error */
	SERR_DISPARITY		= (1 << 20), /* Disparity */
	SERR_CRC		= (1 << 21), /* CRC error */
	SERR_HANDSHAKE		= (1 << 22), /* Handshake error */
	SERR_LINK_SEQ_ERR	= (1 << 23), /* Link sequence error */
	SERR_TRANS_ST_ERROR	= (1 << 24), /* Transport state trans. error */
	SERR_UNRECOG_FIS	= (1 << 25), /* Unrecognized FIS */
	SERR_DEV_XCHG		= (1 << 26), /* device exchanged */

	/* struct ata_taskfile flags */
	ATA_TFLAG_LBA48		= (1 << 0), /* enable 48-bit LBA and "HOB" */
	ATA_TFLAG_ISADDR	= (1 << 1), /* enable r/w to nsect/lba regs */
	ATA_TFLAG_DEVICE	= (1 << 2), /* enable r/w to device reg */
	ATA_TFLAG_WRITE		= (1 << 3), /* data dir: host->dev==1 (write) */
	ATA_TFLAG_LBA		= (1 << 4), /* enable LBA */
	ATA_TFLAG_FUA		= (1 << 5), /* enable FUA */
	ATA_TFLAG_POLLING	= (1 << 6), /* set nIEN to 1 and use polling */

	/* protocol flags */
	ATA_PROT_FLAG_PIO	= (1 << 0), /* is PIO */
	ATA_PROT_FLAG_DMA	= (1 << 1), /* is DMA */
	ATA_PROT_FLAG_DATA	= ATA_PROT_FLAG_PIO | ATA_PROT_FLAG_DMA,
	ATA_PROT_FLAG_NCQ	= (1 << 2), /* is NCQ */
	ATA_PROT_FLAG_ATAPI	= (1 << 3), /* is ATAPI */
};

enum ata_tf_protocols {
	/* ATA taskfile protocols */
	ATA_PROT_UNKNOWN,	/* unknown/invalid */
	ATA_PROT_NODATA,	/* no data */
	ATA_PROT_PIO,		/* PIO data xfer */
	ATA_PROT_DMA,		/* DMA */
	ATA_PROT_NCQ,		/* NCQ */
	ATAPI_PROT_NODATA,	/* packet command, no data */
	ATAPI_PROT_PIO,		/* packet command, PIO data xfer*/
	ATAPI_PROT_DMA,		/* packet command with special DMA sauce */
};

enum ata_ioctls {
	ATA_IOC_GET_IO32	= 0x309,
	ATA_IOC_SET_IO32	= 0x324,
};

enum ata_dev_typed {
	ATA_DEV_ATA,		/* ATA device */
	ATA_DEV_ATAPI,		/* ATAPI device */
	ATA_DEV_PMP,		/* Port Multiplier Port */
	ATA_DEV_UNKNOWN,	/* unknown */
};

struct ata_taskfile {
	unsigned long		flags;		/* ATA_TFLAG_xxx */
	u8			protocol;	/* ATA_PROT_xxx */

	u8			ctl;		/* control reg */

	u8			hob_feature;	/* additional data */
	u8			hob_nsect;	/* to support LBA48 */
	u8			hob_lbal;
	u8			hob_lbam;
	u8			hob_lbah;

	u8			feature;
	u8			nsect;
	u8			lbal;
	u8			lbam;
	u8			lbah;

	u8			device;

	u8			command;	/* IO operation */
};

/*
 * protocol tests
 */
static inline unsigned int ata_prot_flags(u8 prot)
{
	switch (prot) {
	case ATA_PROT_NODATA:
		return 0;
	case ATA_PROT_PIO:
		return ATA_PROT_FLAG_PIO;
	case ATA_PROT_DMA:
		return ATA_PROT_FLAG_DMA;
	case ATA_PROT_NCQ:
		return ATA_PROT_FLAG_DMA | ATA_PROT_FLAG_NCQ;
	case ATAPI_PROT_NODATA:
		return ATA_PROT_FLAG_ATAPI;
	case ATAPI_PROT_PIO:
		return ATA_PROT_FLAG_ATAPI | ATA_PROT_FLAG_PIO;
	case ATAPI_PROT_DMA:
		return ATA_PROT_FLAG_ATAPI | ATA_PROT_FLAG_DMA;
	}
	return 0;
}

static inline int ata_is_atapi(u8 prot)
{
	return ata_prot_flags(prot) & ATA_PROT_FLAG_ATAPI;
}

static inline int ata_is_nodata(u8 prot)
{
	return !(ata_prot_flags(prot) & ATA_PROT_FLAG_DATA);
}

static inline int ata_is_pio(u8 prot)
{
	return ata_prot_flags(prot) & ATA_PROT_FLAG_PIO;
}

static inline int ata_is_dma(u8 prot)
{
	return ata_prot_flags(prot) & ATA_PROT_FLAG_DMA;
}

static inline int ata_is_ncq(u8 prot)
{
	return ata_prot_flags(prot) & ATA_PROT_FLAG_NCQ;
}

static inline int ata_is_data(u8 prot)
{
	return ata_prot_flags(prot) & ATA_PROT_FLAG_DATA;
}

/*
 * id tests
 */
#define ata_id_is_ata(id)		(((id)[0] & (1 << 15)) == 0)
#define ata_id_has_lba(id)		((id)[49] & (1 << 9))
#define ata_id_has_dma(id)		((id)[49] & (1 << 8))
#define ata_id_has_ncq(id)		((id)[76] & (1 << 8))
#define ata_id_queue_depth(id)		(((id)[75] & 0x1f) + 1)
#define ata_id_removeable(id)		((id)[0] & (1 << 7))
#define ata_id_iordy_disable(id)	((id)[49] & (1 << 10))
#define ata_id_has_iordy(id)		((id)[49] & (1 << 11))

#define ata_id_u32(id,n)	\
	(((u32) (id)[(n) + 1] << 16) | ((u32) (id)[(n)]))
#define ata_id_u64(id,n)	\
	( ((u64) (id)[(n) + 3] << 48) | \
	  ((u64) (id)[(n) + 2] << 32) | \
	  ((u64) (id)[(n) + 1] << 16) | \
	  ((u64) (id)[(n) + 0]) )

#define ata_id_cdb_intr(id)		(((id)[0] & 0x60) == 0x20)

static inline int ata_id_has_fua(const u16 *id)
{
	if ((id[84] & 0xC000) != 0x4000)
		return 0;
	return id[84] & (1 << 6);
}

static inline int ata_id_has_flush(const u16 *id)
{
	if ((id[83] & 0xC000) != 0x4000)
		return 0;
	return id[83] & (1 << 12);
}

static inline int ata_id_has_flush_ext(const u16 *id)
{
	if ((id[83] & 0xC000) != 0x4000)
		return 0;
	return id[83] & (1 << 13);
}

static inline int ata_id_has_lba48(const u16 *id)
{
	if ((id[83] & 0xC000) != 0x4000)
		return 0;
	if (!ata_id_u64(id, 100))
		return 0;
	return id[83] & (1 << 10);
}

static inline int ata_id_hpa_enabled(const u16 *id)
{
	/* Yes children, word 83 valid bits cover word 82 data */
	if ((id[83] & 0xC000) != 0x4000)
		return 0;
	/* And 87 covers 85-87 */
	if ((id[87] & 0xC000) != 0x4000)
		return 0;
	/* Check command sets enabled as well as supported */
	if ((id[85] & ( 1 << 10)) == 0)
		return 0;
	return id[82] & (1 << 10);
}

static inline int ata_id_has_wcache(const u16 *id)
{
	/* Yes children, word 83 valid bits cover word 82 data */
	if ((id[83] & 0xC000) != 0x4000)
		return 0;
	return id[82] & (1 << 5);
}

static inline int ata_id_has_pm(const u16 *id)
{
	if ((id[83] & 0xC000) != 0x4000)
		return 0;
	return id[82] & (1 << 3);
}

static inline int ata_id_rahead_enabled(const u16 *id)
{
	if ((id[87] & 0xC000) != 0x4000)
		return 0;
	return id[85] & (1 << 6);
}

static inline int ata_id_wcache_enabled(const u16 *id)
{
	if ((id[87] & 0xC000) != 0x4000)
		return 0;
	return id[85] & (1 << 5);
}

static inline unsigned int ata_id_major_version(const u16 *id)
{
	unsigned int mver;

	if (id[ATA_ID_MAJOR_VER] == 0xFFFF)
		return 0;

	for (mver = 14; mver >= 1; mver--)
		if (id[ATA_ID_MAJOR_VER] & (1 << mver))
			break;
	return mver;
}

static inline int ata_id_is_sata(const u16 *id)
{
	return ata_id_major_version(id) >= 5 && id[93] == 0;
}

static inline int ata_id_has_tpm(const u16 *id)
{
	/* The TPM bits are only valid on ATA8 */
	if (ata_id_major_version(id) < 8)
		return 0;
	if ((id[48] & 0xC000) != 0x4000)
		return 0;
	return id[48] & (1 << 0);
}

static inline int ata_id_has_dword_io(const u16 *id)
{
	/* ATA 8 reuses this flag for "trusted" computing */
	if (ata_id_major_version(id) > 7)
		return 0;
	if (id[48] & (1 << 0))
		return 1;
	return 0;
}

static inline int ata_id_current_chs_valid(const u16 *id)
{
	/* For ATA-1 devices, if the INITIALIZE DEVICE PARAMETERS command
	   has not been issued to the device then the values of
	   id[54] to id[56] are vendor specific. */
	return (id[53] & 0x01) && /* Current translation valid */
		id[54] &&  /* cylinders in current translation */
		id[55] &&  /* heads in current translation */
		id[55] <= 16 &&
		id[56];    /* sectors in current translation */
}

static inline int ata_id_is_cfa(const u16 *id)
{
	u16 v = id[0];
	if (v == 0x848A)	/* Standard CF */
		return 1;
	/* Could be CF hiding as standard ATA */
	if (ata_id_major_version(id) >= 3 &&  id[82] != 0xFFFF &&
			(id[82] & ( 1 << 2)))
		return 1;
	return 0;
}

static inline int ata_drive_40wire(const u16 *dev_id)
{
	if (ata_id_is_sata(dev_id))
		return 0;	/* SATA */
	if ((dev_id[93] & 0xE000) == 0x6000)
		return 0;	/* 80 wire */
	return 1;
}

static inline int ata_drive_40wire_relaxed(const u16 *dev_id)
{
	if ((dev_id[93] & 0x2000) == 0x2000)
		return 0;	/* 80 wire */
	return 1;
}

static inline int atapi_cdb_len(const u16 *dev_id)
{
	u16 tmp = dev_id[0] & 0x3;
	switch (tmp) {
	case 0:		return 12;
	case 1:		return 16;
	default:	return -1;
	}
}

static inline int atapi_command_packet_set(const u16 *dev_id)
{
	return (dev_id[0] >> 8) & 0x1f;
}

static inline int atapi_id_dmadir(const u16 *dev_id)
{
	return ata_id_major_version(dev_id) >= 7 && (dev_id[62] & 0x8000);
}

static inline int is_multi_taskfile(struct ata_taskfile *tf)
{
	return (tf->command == ATA_CMD_READ_MULTI) ||
	       (tf->command == ATA_CMD_WRITE_MULTI) ||
	       (tf->command == ATA_CMD_READ_MULTI_EXT) ||
	       (tf->command == ATA_CMD_WRITE_MULTI_EXT) ||
	       (tf->command == ATA_CMD_WRITE_MULTI_FUA_EXT);
}

static inline int ata_ok(u8 status)
{
	return ((status & (ATA_BUSY | ATA_DRDY | ATA_DF | ATA_DRQ | ATA_ERR))
			== ATA_DRDY);
}

static inline int lba_28_ok(u64 block, u32 n_block)
{
	/* check the ending block number */
	return ((block + n_block - 1) < ((u64)1 << 28)) && (n_block <= 256);
}

static inline int lba_48_ok(u64 block, u32 n_block)
{
	/* check the ending block number */
	return ((block + n_block - 1) < ((u64)1 << 48)) && (n_block <= 65536);
}

#define sata_pmp_gscr_vendor(gscr)	((gscr)[SATA_PMP_GSCR_PROD_ID] & 0xffff)
#define sata_pmp_gscr_devid(gscr)	((gscr)[SATA_PMP_GSCR_PROD_ID] >> 16)
#define sata_pmp_gscr_rev(gscr)		(((gscr)[SATA_PMP_GSCR_REV] >> 8) & 0xff)
#define sata_pmp_gscr_ports(gscr)	((gscr)[SATA_PMP_GSCR_PORT_INFO] & 0xf)

u64 ata_id_n_sectors(u16 *id);
u32 ata_dev_classify(u32 sig);
void ata_id_c_string(const u16 *id, unsigned char *s,
			 unsigned int ofs, unsigned int len);
void ata_dump_id(u16 *id);
void ata_swap_buf_le16(u16 *buf, unsigned int buf_words);

#endif /* __LIBATA_H__ */