update/fix AcTux4 board
Signed-off-by: Michael Schwingen <michael@schwingen.org>
diff --git a/include/configs/actux4.h b/include/configs/actux4.h
index 6718921..190de5a 100644
--- a/include/configs/actux4.h
+++ b/include/configs/actux4.h
@@ -37,12 +37,11 @@
#define CONFIG_BAUDRATE 115200
#define CONFIG_BOOTDELAY 3
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
+#define CONFIG_BOARD_EARLY_INIT_F 1
/***************************************************************
* U-boot generic defines start here.
***************************************************************/
-#undef CONFIG_USE_IRQ
-
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024)
@@ -54,6 +53,15 @@
#define CONFIG_CMD_ELF
+#define CONFIG_PCI
+#ifdef CONFIG_PCI
+#define CONFIG_CMD_PCI
+#define CONFIG_PCI_PNP
+#define CONFIG_IXP_PCI
+#define CONFIG_PCI_SCAN_SHOW
+#define CONFIG_CMD_PCI_ENUM
+#endif
+
#define CONFIG_BOOTCOMMAND "run boot_flash"
/* enable passing of ATAGs */
#define CONFIG_CMDLINE_TAG 1
@@ -81,8 +89,9 @@
#define CONFIG_SYS_MEMTEST_START 0x00400000
#define CONFIG_SYS_MEMTEST_END 0x00800000
-/* spec says 66.666 MHz, but it appears to be 33 */
-#define CONFIG_SYS_HZ 3333333
+/* timer clock - 2* OSC_IN system clock */
+#define CONFIG_IXP425_TIMER_CLK 66000000
+#define CONFIG_SYS_HZ 1000
/* default load address */
#define CONFIG_SYS_LOAD_ADDR 0x00010000
@@ -97,10 +106,6 @@
* The stack sizes are set up in start.S using the settings below
*/
#define CONFIG_STACKSIZE (128*1024) /* regular stack */
-#ifdef CONFIG_USE_IRQ
-# define CONFIG_STACKSIZE_IRQ (4*1024) /* IRQ stack */
-# define CONFIG_STACKSIZE_FIQ (4*1024) /* FIQ stack */
-#endif
/* Expansion bus settings */
#define CONFIG_SYS_EXP_CS0 0xbd113003
@@ -108,7 +113,7 @@
/* SDRAM settings */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM_1 0x00000000
-#define CONFIG_SYS_DRAM_BASE 0x00000000
+#define CONFIG_SYS_SDRAM_BASE 0x00000000
/* 32MB SDRAM */
#define CONFIG_SYS_SDR_CONFIG 0x18
@@ -118,6 +123,7 @@
#define CONFIG_SYS_DRAM_SIZE 0x02000000
/* FLASH organization */
+#define CONFIG_SYS_TEXT_BASE 0x50000000
#define CONFIG_SYS_MAX_FLASH_BANKS 2
/* max # of sectors per chip */
#define CONFIG_SYS_MAX_FLASH_SECT 70
@@ -128,6 +134,7 @@
#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
#define CONFIG_SYS_MONITOR_BASE PHYS_FLASH_1
#define CONFIG_SYS_MONITOR_LEN (252 << 10)
+#define CONFIG_BOARD_SIZE_LIMIT 258048
/* Use common CFI driver */
#define CONFIG_SYS_FLASH_CFI
@@ -152,6 +159,7 @@
#define CONFIG_PHY_ADDR 0x1C
/* MII PHY management */
#define CONFIG_MII 1
+
/* Number of ethernet rx buffers & descriptors */
#define CONFIG_SYS_RX_ETH_BUFFER 16
@@ -180,19 +188,22 @@
"mtd=IXP4XX-Flash.0:252k(uboot),4k(uboot_env);" \
"IXP4XX-Flash.1:128k(ucode),1280k(linux),-(root)\0" \
"kerneladdr=51020000\0" \
+ "kernelfile=actux4/uImage\0" \
+ "rootfile=actux4/rootfs\0" \
"rootaddr=51160000\0" \
"loadaddr=10000\0" \
"updateboot_ser=mw.b 10000 ff 40000;" \
" loady ${loadaddr};" \
" run eraseboot writeboot\0" \
"updateboot_net=mw.b 10000 ff 40000;" \
- " tftp ${loadaddr} u-boot.bin;" \
+ " tftp ${loadaddr} actux4/u-boot.bin;" \
" run eraseboot writeboot\0" \
"eraseboot=protect off 50000000 5003efff;" \
" erase 50000000 +${filesize}\0" \
"writeboot=cp.b 10000 50000000 ${filesize}\0" \
- "eraseenv=protect off 5003f000 5003ffff;" \
- " erase 5003f000 5003ffff\0" \
+ "updateucode=loady;" \
+ " era ${npe_ucode} +${filesize};" \
+ " cp.b ${loadaddr} ${npe_ucode} ${filesize}\0" \
"updateroot=tftp ${loadaddr} ${rootfile};" \
" era ${rootaddr} +${filesize};" \
" cp.b ${loadaddr} ${rootaddr} ${filesize}\0" \
@@ -211,4 +222,8 @@
" tftpboot ${loadaddr} ${kernelfile};" \
" bootm\0"
+/* additions for new relocation code, must be added to all boards */
+#define CONFIG_SYS_INIT_SP_ADDR \
+ (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
+
#endif /* __CONFIG_H */