mtd: vf610_nfc: add 32-error correction option for HW ECC
Add option to choose between current 24-error correction and 32-error
correction through Kconfig. 32-error correction allow to use NAND
chips which require up to 8-bit error correction per 512 byte (when
using 2K pages).
Signed-off-by: Stefan Agner <stefan@agner.ch>
diff --git a/drivers/mtd/nand/vf610_nfc.c b/drivers/mtd/nand/vf610_nfc.c
index 05cbdf3..2c02ff5 100644
--- a/drivers/mtd/nand/vf610_nfc.c
+++ b/drivers/mtd/nand/vf610_nfc.c
@@ -71,6 +71,7 @@
/* NFC ECC mode define */
#define ECC_BYPASS 0
#define ECC_45_BYTE 6
+#define ECC_60_BYTE 7
/*** Register Mask and bit definitions */
@@ -155,7 +156,10 @@
#define mtd_to_nfc(_mtd) \
(struct vf610_nfc *)((struct nand_chip *)_mtd->priv)->priv
-static struct nand_ecclayout vf610_nfc_ecc45 = {
+#if defined(CONFIG_SYS_NAND_VF610_NFC_45_ECC_BYTES)
+#define ECC_HW_MODE ECC_45_BYTE
+
+static struct nand_ecclayout vf610_nfc_ecc = {
.eccbytes = 45,
.eccpos = {19, 20, 21, 22, 23,
24, 25, 26, 27, 28, 29, 30, 31,
@@ -167,6 +171,24 @@
{.offset = 8,
.length = 11} }
};
+#elif defined(CONFIG_SYS_NAND_VF610_NFC_60_ECC_BYTES)
+#define ECC_HW_MODE ECC_60_BYTE
+
+static struct nand_ecclayout vf610_nfc_ecc = {
+ .eccbytes = 60,
+ .eccpos = { 4, 5, 6, 7, 8, 9, 10, 11,
+ 12, 13, 14, 15, 16, 17, 18, 19,
+ 20, 21, 22, 23, 24, 25, 26, 27,
+ 28, 29, 30, 31, 32, 33, 34, 35,
+ 36, 37, 38, 39, 40, 41, 42, 43,
+ 44, 45, 46, 47, 48, 49, 50, 51,
+ 52, 53, 54, 55, 56, 57, 58, 59,
+ 60, 61, 62, 63 },
+ .oobfree = {
+ {.offset = 2,
+ .length = 2} }
+};
+#endif
static inline u32 vf610_nfc_read(struct mtd_info *mtd, uint reg)
{
@@ -340,7 +362,7 @@
vf610_nfc_transfer_size(nfc->regs, page_sz);
vf610_nfc_send_commands(nfc->regs, NAND_CMD_SEQIN,
command, PROGRAM_PAGE_CMD_CODE);
- vf610_nfc_ecc_mode(mtd, ECC_45_BYTE);
+ vf610_nfc_ecc_mode(mtd, ECC_HW_MODE);
break;
case NAND_CMD_RESET:
@@ -365,7 +387,7 @@
vf610_nfc_send_commands(nfc->regs, NAND_CMD_READ0,
NAND_CMD_READSTART, READ_PAGE_CMD_CODE);
vf610_nfc_addr_cycle(mtd, column, page);
- vf610_nfc_ecc_mode(mtd, ECC_45_BYTE);
+ vf610_nfc_ecc_mode(mtd, ECC_HW_MODE);
break;
case NAND_CMD_ERASE1:
@@ -645,7 +667,9 @@
goto error;
}
- chip->ecc.layout = &vf610_nfc_ecc45;
+ /* Current HW ECC layouts only use 64 bytes of OOB */
+ if (mtd->oobsize > 64)
+ mtd->oobsize = 64;
/* propagate ecc.layout to mtd_info */
mtd->ecclayout = chip->ecc.layout;
@@ -653,9 +677,15 @@
chip->ecc.write_page = vf610_nfc_write_page;
chip->ecc.mode = NAND_ECC_HW;
- chip->ecc.bytes = 45;
chip->ecc.size = PAGE_2K;
+ chip->ecc.layout = &vf610_nfc_ecc;
+#if defined(CONFIG_SYS_NAND_VF610_NFC_45_ECC_BYTES)
chip->ecc.strength = 24;
+ chip->ecc.bytes = 45;
+#elif defined(CONFIG_SYS_NAND_VF610_NFC_60_ECC_BYTES)
+ chip->ecc.strength = 32;
+ chip->ecc.bytes = 60;
+#endif
/* Enable ECC_STATUS */
vf610_nfc_set(mtd, NFC_FLASH_CONFIG, CONFIG_ECC_SRAM_REQ_BIT);