Revert "powerpc: ppc4xx: remove lwmon5 support"
This reverts commit 8fe11b8901a31d11990488c82bc23612589d57be.
I'll add support to lwmon5 in the next patch and will remove
support for the broken lcd4_lwmon5 as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
diff --git a/board/lwmon5/init.S b/board/lwmon5/init.S
new file mode 100644
index 0000000..e5207c2
--- /dev/null
+++ b/board/lwmon5/init.S
@@ -0,0 +1,75 @@
+/*
+ * (C) Copyright 2007
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * Copyright (C) 2002 Scott McNutt <smcnutt@artesyncp.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <asm-offsets.h>
+#include <ppc_asm.tmpl>
+#include <config.h>
+#include <asm/mmu.h>
+
+/**************************************************************************
+ * TLB TABLE
+ *
+ * This table is used by the cpu boot code to setup the initial tlb
+ * entries. Rather than make broad assumptions in the cpu source tree,
+ * this table lets each board set things up however they like.
+ *
+ * Pointer to the table is returned in r1
+ *
+ *************************************************************************/
+ .section .bootpg,"ax"
+ .globl tlbtab
+
+tlbtab:
+ tlbtab_start
+
+ /*
+ * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the
+ * speed up boot process. It is patched after relocation to enable SA_I
+ */
+ tlbentry(CONFIG_SYS_BOOT_BASE_ADDR, SZ_256M, CONFIG_SYS_BOOT_BASE_ADDR, 1, AC_RWX | SA_G)
+
+ /*
+ * TLB entries for SDRAM are not needed on this platform.
+ * They are dynamically generated in the SPD DDR(2) detection
+ * routine.
+ */
+
+#ifdef CONFIG_SYS_INIT_RAM_DCACHE
+ /* TLB-entry for init-ram in dcache (SA_I must be turned off!) */
+ tlbentry(CONFIG_SYS_INIT_RAM_ADDR, SZ_4K, CONFIG_SYS_INIT_RAM_ADDR, 0, AC_RWX | SA_G)
+#endif
+
+ /* TLB-entry for PCI Memory */
+ tlbentry(CONFIG_SYS_PCI_MEMBASE, SZ_256M, CONFIG_SYS_PCI_MEMBASE, 1, AC_RW | SA_IG)
+ tlbentry(CONFIG_SYS_PCI_MEMBASE1, SZ_256M, CONFIG_SYS_PCI_MEMBASE1, 1, AC_RW | SA_IG)
+ tlbentry(CONFIG_SYS_PCI_MEMBASE2, SZ_256M, CONFIG_SYS_PCI_MEMBASE2, 1, AC_RW | SA_IG)
+ tlbentry(CONFIG_SYS_PCI_MEMBASE3, SZ_256M, CONFIG_SYS_PCI_MEMBASE3, 1, AC_RW | SA_IG)
+
+ /* TLB-entry for the FPGA Chip select 2 */
+ tlbentry(CONFIG_SYS_FPGA_BASE_0, SZ_1M, CONFIG_SYS_FPGA_BASE_0, 1, AC_RWX | SA_I|SA_G)
+
+ /* TLB-entry for the FPGA Chip select 3 */
+ tlbentry(CONFIG_SYS_FPGA_BASE_1, SZ_1M, CONFIG_SYS_FPGA_BASE_1, 1,AC_RWX | SA_I|SA_G)
+
+ /* TLB-entry for the LIME Controller */
+ tlbentry(CONFIG_SYS_LIME_BASE_0, SZ_16M, CONFIG_SYS_LIME_BASE_0, 1, AC_RWX | SA_I|SA_G)
+ tlbentry(CONFIG_SYS_LIME_BASE_1, SZ_16M, CONFIG_SYS_LIME_BASE_1, 1, AC_RWX | SA_I|SA_G)
+ tlbentry(CONFIG_SYS_LIME_BASE_2, SZ_16M, CONFIG_SYS_LIME_BASE_2, 1, AC_RWX | SA_I|SA_G)
+ tlbentry(CONFIG_SYS_LIME_BASE_3, SZ_16M, CONFIG_SYS_LIME_BASE_3, 1, AC_RWX | SA_I|SA_G)
+
+ /* TLB-entry for Internal Registers & OCM */
+ tlbentry(0xe0000000, SZ_16M, 0xe0000000, 0, AC_RWX | SA_I)
+
+ /*TLB-entry PCI registers*/
+ tlbentry(0xEEC00000, SZ_1K, 0xEEC00000, 1, AC_RWX | SA_IG)
+
+ /* TLB-entry for peripherals */
+ tlbentry(0xEF000000, SZ_16M, 0xEF000000, 1, AC_RWX | SA_IG)
+
+ tlbtab_end